Showing 1113 results for ""

Worn rubber differential mounts will lead to the differential twisting and shifting around in the rear subframe. Not only will this be noisy but it's bad for driver confidence and bad for the chassis as well. Even on fresh rubber bushings the differential has deflection and twist, especially if the car has been modified for more torque. Since the differential is centrally mounted in the rear subframe, with all suspension mounts interconnected, a differential with too much deflection will affect handling and could even damage the rear subframe.

These 88A urethane E46 M3 diff mounts are much stiffer than stock but still not as solid as our Turner aluminum/Delrin bushings. This set will resist twisting much better than the stock rubber mounts. Included is the front diff mount and two rear mounts in the cover.

A common source of leaks, the selector shaft seal should be replaced whenever the shifter assembly is serviced to prevent fluid loss.

Fits the following BMW chassis:
E36, E39, E46, E36/7 Z3

Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.

By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components. 

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Stock mounts are made from soft rubber and are sometimes filled with fluid to give a car the most comfortable ride possible. The soft rubber and fluid helps to reduce the total amount of vibration, noise, and harshness (NVH) that is transferred into the cabin. The problem with this is driveline slop. The stock mounts allow a lot of excess movement and increases the amount of time it takes to transfer power to the wheels.

In order to address this issue, performance mounts can be substituted to reduce the amount of slop and transfer power to the wheel quicker. Two options for this are polyurethane mounts and solid mounts.

Solid mounts are great for an immediate transfer of power but allow for a ton of noise and vibration to be felt and heard in the cabin of the vehicle. This is great for the track where there aren't any issues with excess harshness, but as a daily driver, this can become an annoying pain in the neck.

The best middle ground is Polyurethane. Polyurethane is much stiffer than rubber and gives you the much stiffer feel you may be looking for. This allows for the increase in responsiveness, but isn't so extreme that it transfers all of the sound and vibrations into the cabin. This makes it much more comfortable for daily use while still reinforcing your driveline.

Features:

• Aluminum and Polyurethane Construction
• 80A Durometer Rating
• New Hardware

Replace this tube whenever the bearing or clutch kit is replaced.

Genuine BMW Guide Tube
This item fits the following BMW Chassis:
E36 M3,E34,E36,E39,E46,E53 X5
 

URO Front Inner Left/Right BMW Wheel Hub Dust Cap

The URO Front Inner Left/Right BMW Wheel Hub Dust Cap is a high-quality replacement designed to protect your BMW’s wheel bearings from dirt, moisture, and debris. This direct-fit OE replacement ensures a secure and proper seal, preventing premature wear and extending the lifespan of the wheel hub assembly. Manufactured from durable, heat-resistant materials, this dust cap withstands high temperatures and road vibrations for long-term reliability. Designed for easy installation, it restores proper bearing protection and helps maintain optimal wheel performance.

Key Benefits:

• Direct-fit OE replacement for seamless installation and a perfect seal
• Protects wheel bearings from dirt, moisture, and debris to prevent premature wear
• Durable construction resists heat and road vibrations for long-lasting performance
• Restores proper bearing protection for improved reliability and efficiency
• Precision-engineered to meet BMW specifications for an exact fit

Ensure your BMW’s wheel bearings stay properly protected with the URO Front Inner Left/Right BMW Wheel Hub Dust Cap for enhanced performance and longevity.