BMW Engine Parts for BMW 3 Series E46 (1999-2005)

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On older BMWs, the engine ground strap is a thin, non-insulated cable that spans from the engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for E30 (318i/is), E36, E39, E46, and others Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12421737755 and 12421714262.

Elevate your custom installation with the ECS -10AN O-Ring Boss fitting, a crucial component that connects your ECS Tuning Catch Can to a 3/4" ID hose. This fitting simplifies your plumbing setup, ensuring a seamless solution.

Featuring a pre-installed Viton O-ring, this fitting is engineered for excellence, providing a leak-proof seal that resists the effects of oil and fuel exposure, guaranteeing long-term durability.

The 3/4" nipple is thoughtfully designed with barbs to secure hose position effectively, minimizing the risk of hose disconnection. Keep in mind that clamps and hoses are available for separate purchase. These fittings are sold individually, with most installations requiring a pair of them.

A beautiful addition and durable upgrade for your engine

Tired of staring at that bright red plastic oil dipstick? Waiting for a way to add a nice touch to your engine bay without going over the top? ECS Tuning is proud to announce our billet aluminum oil dipstick! Designed to OE specifications with an easy-to-read fill line, we offer three different finishes. Available in black, polished, or clear anodized, we have an offering for every type of enthusiast. Not only does it look better, but also performs better. Because of the durability, it is easier to insert than the factory ribbon dipstick. So, no more fighting with your dipstick to re-install it.

Ensure optimal fuel delivery for your BMW's engine with the Turner Motorsport Fuel Filter for E46 M3 & Z3 S54 3.2L Engine. Over time, fuel filters can become clogged, hindering the engine's ability to receive sufficient fuel. This can lead to various fuel-related issues such as surging, stalling, cold start problems, and decreased performance. Replacing the fuel filter with a fresh one helps address these issues and ensures smooth engine operation under various conditions.

Benefits:

• Improves fuel delivery to the engine
• Addresses fuel-related problems such as surging and stalling
• Enhances cold start performance
• Maintains engine performance under various driving conditions
• Recommended replacement every 60,000 miles, or more frequently in regions with poor fuel quality

This is an OEM MAHLE fuel filter that removes dirt and other particle contaminants from your fuel.

A clogged fuel filter makes it difficult for your engine to get all the fueling it needs. Filters commonly clog from a deteriorating gas tank, bad fuel, or other debris in the fuel system. A fresh fuel filter addresses many fuel related problems including surging, stalling, cold start issues, and poor performance under a variety of conditions.

The main reason all of the VANOS units will eventually fail is because the material used for the sealing rings from the factory is not designed for that type of environment. When this happens the only option that BMW leaves you with is buying a new and expensive VANOS unit with the same sealing rings that failed in your original unit.

The VANOS system found in BMW engines is a great feature (when it’s working properly), keeping your power curve smooth and responsive especially in lower to mid RPM range. What usually goes unnoticed is the gradual loss of power within this range as the vehicle's age due to slowly failing seals within the VANOS unit. The way the VANOS system works is based off of oil pressure triggered by a solenoid that allows for a small range of timing degree adjustment, this is where the power curve is affected. When the seals begin to fail (all of them do) there is less pressure to advance the timing reducing the power in that low to mid range. Because this happens slowly it's very hard to notice a difference until you refresh your VANOS unit, then you easily realize the response you've been missing.

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you're replacing the seals in your VANOS unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy VANOS clatter.

Seals & O-rings:

The seals  were the main focus of this project since the OE units are built with Buna-N rubber o-rings instead of the ECS supplied Viton rubber o-rings. The Buna-N material quickly hardens from the heat and chemical exposure within the engine, where the Viton is significantly more resistant to these chemicals. This knowledge was also used when it came to the commonly failed o-rings found on the VANOS seal plate, replaced at the solenoid.

Rattle Repair:

When it comes to the VANOS rattle this is commonly described as "marbles in a can", and can be heard throughout the different RPM ranges depending on the engine. These upgraded rings and washers are precision ground from hardened steel to resist wear and deformation keeping your VANOS rattle free. The rattle repair tools are designed specifically for this VANOS anti-rattle repair, design from hardened steel to stand up to the job. Designed to perfectly follow the splines of the shaft for a tight grip when applying the necessary torque to disassemble & reassemble the VANOS transfer gear. The keyed socket was designed with the intent to use a "common" wrench so this can be completed at home in your garage.    

When Servicing your VANOS unit we recommend getting everything you need to replace on the way to service which includes an oil change and valve cover gasket set. Fresh oil and gaskets is the best way to start off a fresh rebuild of any kind giving you the maximum performance of your freshly serviced components.

Don't forget to check out our rebuild PDF to make sure you have everything to get the job done and eliminate the rebuild guess work.

This item fits the following BMWs: 
2000-2001 E46 3 Series M3 M3 Convertible 2000-2006 
2001-2002 Z3 Roadster / Coupe Z3 M Roadster Z3 M Coupe w S54 Engine 
2006-2008 E86 E86 Z4 Z4 M Roadster Z4 M Coupe

Long lasting alternative for sealing plate 11367831906. This sealing flange is located between the VAN0S adjusting unit and the VAN0S solenoid on the S54 engine. It can be the source of oil leaks and should be replaced when the the VAN0S solenoid is.

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe (S54)
2006-2008 E85 BMW Z4 M Roadster M Coupe

Meet modern emission regulations while preserving engine performance with the ECS Baffled Oil Catch Can. Designed for BMW and MINI vehicles, this system efficiently captures blow-by gases, preventing excessive oil vapor ingestion into the intake tract. The innovative 4-chamber baffle system maximizes oil/air separation, reducing carbon build-up and pollutants. Featuring a 1/4" drain fitting for easy maintenance, this catch can minimizes oil deposits, ensuring cleaner emissions and enhanced engine performance.

Key Benefits:

• Efficient 4-chamber baffle system for maximum oil/air separation
• Recirculated design reduces oil ingestion, promoting cleaner emissions
• Durable 6061-T6 billet machined body with anodized black finish for longevity
• Integrated dipstick and sealed reservoir for easy oil inspection and maintenance
• Serviceable design with removable baffle plates for cleaning
• Easy installation with customizable mounting options and leak-free fittings
• Engineered and manufactured in the USA for superior performance and durability

Note: Not for sale or use in the state of California on any pollution-controlled vehicle as per the California Air Resources Board.

This is the BMW crankcase return line that goes from the intake manifold to the top CCV connecting hose. We also offer a complete CCV repair kit
Since the late 1800’s Febi has been fabricating replacement metal parts. This history is self evident in the quality and vast amount of applications they service. With more than 34,000 repair solutions for cars and commercial vehicles you can be sure Febi has you covered.

This item fits the following BMWs:
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1997-2003 E39 BMW 525i 528i 530i
2004-2010 E60 BMW 525i 530i
2004-2005 E83 BMW X3 2.5i X3 3.0i X3 3.0si
2000-2006 E53 BMW X5 3.0i
1/2000-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
2003-2005 E85 BMW Z4 2.5i Z4 3.0i