BMW Engine Parts for BMW 3 Series E46 (1999-2005)

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On older BMWs, the engine ground strap is a thin, non-insulated cable that spans from the engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for E30 (318i/is), E36, E39, E46, and others Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12421737755 and 12421714262.

Elevate your custom installation with the ECS -10AN O-Ring Boss fitting, a crucial component that connects your ECS Tuning Catch Can to a 3/4" ID hose. This fitting simplifies your plumbing setup, ensuring a seamless solution.

Featuring a pre-installed Viton O-ring, this fitting is engineered for excellence, providing a leak-proof seal that resists the effects of oil and fuel exposure, guaranteeing long-term durability.

The 3/4" nipple is thoughtfully designed with barbs to secure hose position effectively, minimizing the risk of hose disconnection. Keep in mind that clamps and hoses are available for separate purchase. These fittings are sold individually, with most installations requiring a pair of them.

Spark Plug Gapper Tool BMS Billet is essential for accurately adjusting the gap of spark plugs. This precision tool ensures that each plug is set to the exact specifications required for optimal engine performance. Made in the USA, it features a 12mm plug thread size, making it suitable for a wide range of applications.

• Precision Adjustment: Allows for accurate gap adjustments to ensure optimal spark performance and engine efficiency.
• Speed and Efficiency: Streamlines the process of gapping plugs while maintaining high precision, saving time and effort.
• High-Quality Construction: Crafted from billet materials for durability and reliability, ensuring long-term use.
• Lifetime Replacement Program: Comes with a lifetime replacement guarantee, reflecting confidence in the tool's quality and performance.

Upgrade your spark plug maintenance with the Spark Plug Gapper Tool BMS Billet for a reliable and precise solution.

After the introduction of the M52TU/M54 engines, BMW observed an uptick in CCV-related issues, especially in cold regions. Vehicles operating in extremely low temperatures often encountered a blockage in the CCV dipstick hose, leading to elevated crankcase pressure and visible blue smoke from the exhaust. To address this issue, BMW introduced cold climate-specific hoses with foam insulation, preventing condensation and facilitating quicker oil warm-up. This kit incorporates top-notch reproduction cold climate hoses to ensure optimal CCV performance across all weather conditions.

The crankcase ventilation valve, known as the oil separator, PCV, CCV, or crankcase pressure regulator valve, plays a vital role in redirecting oil from your vehicle's intake system back into the engine oil pan. This system comprises numerous plastic and rubber hoses, prone to damage due to prolonged exposure to chemicals and heat.

Designed to tackle or prevent impending CCV system failures, this kit includes four foam-insulated hoses made from durable plastic capable of withstanding heat fluctuations and chemical exposure. Additionally, a new ventilation valve is included for a comprehensive and long-lasting repair solution.

Signs indicating the need for crankcase ventilation system replacement include:

Whistling sounds from the intake manifold, caused by crankcase pressure venting through holes in the CCV hoses. Blue smoke emitting from the tailpipe, indicating oil consumption. Excessive oil usage. Milky or yellowish buildup under the oil cap, suggesting condensation due to ventilation valve malfunction. If you're experiencing misfires, lean fuel codes, decreased fuel efficiency, or noticeable oil consumption, it's advisable to overhaul your crankcase ventilation system. Opt for this reliable system from Febi-Bilstein for a repair that meets factory standards and ensures consistent performance.

The temperature sensor is mounted in either the intake manifold or the intake air box assembly depending on the model of car. This OEM Hella replacement will insure proper readings and fuel/air mixtures for the given temperature.

Hella is a premium manufacturer that supplies automotive parts to numerous car brands across the world. Everything from electrical to mechanical genuine parts have been made and supplied directly to BMW before the vehicles ever leave the production floor. Their high quality, long lasting parts have made them a trusted brand chosen to help keep your BMW on the road for many years to come.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1996-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 328i 328is 328ic M3
1999-2000 E46 BMW 323i 323ci 328i 328ci
2001-2005 E46 BMW 325i 325ci 325xi 330i 330ci 330xi - M54 engine only
1997-2003 E39 BMW 525i 528i 530i 540i
1997-2001 E38 BMW 740i 740il 750il
2004-2006 E83 BMW X3 2.5i X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
1998-2000 Z3 BMW M Roadster M Coupe

These WPC-treated bearings are the best we have seen! WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are original equipment KS bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

This item fits the following BMWs: 
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix 
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1982-1988 E28 BMW 528e
1989-1995 E34 BMW 525i
1997-2003 E39 BMW 525i 528i 530i
2004-2005 E60 BMW 525i 530i 
2004-2006 E83 BMW X3 2.5i X3 3.0i 
2000-2006 E53 BMW X5 3.0i 
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i 

The main reason all of the VANOS units will eventually fail is because the material used for the sealing rings from the factory is not designed for that type of environment. When this happens the only option that BMW leaves you with is buying a new and expensive VANOS unit with the same sealing rings that failed in your original unit.

The VANOS system found in BMW engines is a great feature (when it’s working properly), keeping your power curve smooth and responsive especially in lower to mid RPM range. What usually goes unnoticed is the gradual loss of power within this range as the vehicle's age due to slowly failing seals within the VANOS unit. The way the VANOS system works is based off of oil pressure triggered by a solenoid that allows for a small range of timing degree adjustment, this is where the power curve is affected. When the seals begin to fail (all of them do) there is less pressure to advance the timing reducing the power in that low to mid range. Because this happens slowly it's very hard to notice a difference until you refresh your VANOS unit, then you easily realize the response you've been missing.

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you're replacing the seals in your VANOS unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy VANOS clatter.

Seals & O-rings:

The seals  were the main focus of this project since the OE units are built with Buna-N rubber o-rings instead of the ECS supplied Viton rubber o-rings. The Buna-N material quickly hardens from the heat and chemical exposure within the engine, where the Viton is significantly more resistant to these chemicals. This knowledge was also used when it came to the commonly failed o-rings found on the VANOS seal plate, replaced at the solenoid.

Rattle Repair:

When it comes to the VANOS rattle this is commonly described as "marbles in a can", and can be heard throughout the different RPM ranges depending on the engine. These upgraded rings and washers are precision ground from hardened steel to resist wear and deformation keeping your VANOS rattle free. The rattle repair tools are designed specifically for this VANOS anti-rattle repair, design from hardened steel to stand up to the job. Designed to perfectly follow the splines of the shaft for a tight grip when applying the necessary torque to disassemble & reassemble the VANOS transfer gear. The keyed socket was designed with the intent to use a "common" wrench so this can be completed at home in your garage.    

When Servicing your VANOS unit we recommend getting everything you need to replace on the way to service which includes an oil change and valve cover gasket set. Fresh oil and gaskets is the best way to start off a fresh rebuild of any kind giving you the maximum performance of your freshly serviced components.

Don't forget to check out our rebuild PDF to make sure you have everything to get the job done and eliminate the rebuild guess work.

This item fits the following BMWs: 
2000-2001 E46 3 Series M3 M3 Convertible 2000-2006 
2001-2002 Z3 Roadster / Coupe Z3 M Roadster Z3 M Coupe w S54 Engine 
2006-2008 E86 E86 Z4 Z4 M Roadster Z4 M Coupe

Modern emission regulations require a closed PCV/Breather system for cleaner operation. However, inefficient oil particle capture can lead to excessive oil vapor ingestion, causing carbon buildup, reduced performance, and fuel economy. ECS Tuning's updated ECS Baffled Oil Catch Can, now with an easy-to-empty 1/4" drain fitting, is engineered to collect toxic blow-by gases, minimize carbon deposits, and reduce oil contamination within engine oil. Recirculating oil vapor ensures emissions compliance without venting to the atmosphere.

• Key Features:
• Highly Efficient Oil Separator: Strategically positioned 4 chamber baffle system maximizes oil/air separation and minimizes oil droplets in the intake tract.
• Integrated Dipstick: Knurled and black anodized oil dipstick simplifies oil volume inspection.
• Reservoir: Available in 6oz or 8oz capacity with a 1/4" NPT drain plug fitting.
• Serviceable: Easily removable baffle plates and drain plug for cleaning.
• Easy/Customizable Installation: Combine with the ECS Universal Bracket Kit for simplified installation and adjustable mounting locations.
• Leak-Free Fittings: Machined -10AN ORB (O-Ring Boss) fittings available for secure connections (fittings sold separately).

Used to detect the position of the camshaft, this sensor allows the computer to adjust the ignition timing for optimal performanceand to prevent damage from early or late detonation. Hella replacement sensors will ensure long lasting reliability and will keep your engine running like new.

Hella is a premium manufacturer that supplies automotive parts to numerous car brands across the world. Everything from electrical to mechanical genuine parts have been made and supplied directly to BMW before the vehicles ever leave the production floor. Their high quality, long lasting parts have made them a trusted brand chosen to help keep your BMW on the road for many years to come.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Modern day emissions regulations require the use of a closed crankcase ventilation (PCV) system to recirculate combustion blow-by gases from the crankcase back in to the intake to be burned.  Unfortunately, these blow by gases contain water vapor (which is a byproduct of combustion) and pick up oil mist from and the windage cloud and cam lubrication system as they travel through the crank case.  Due to less than 100% effective air/oil separation in the stock PCV system, some oil mist and water vapor gets carried back to the intake tract and over time cause oil deposits in the intake manifold, intake ports, and on the back of intake valves.  All will eventually lead to poor performance and reduced fuel economy, and the presence of this oil mist in the intake charge may even increase the risk of engine-damaging detonation. 

With forced induction, track use, and/or extended high RPM usage, these symptoms increase as the factory PCV system is overwhelmed, and a catch can becomes a must for your E46 M3. This kit is a direct fit making this an easy reversal if desired as well as maintaining a clean appearance by utilizing the open "smuggler's compartment" on the passenger side of the engine bay.

ECS engineers developed a catch can that utilizes a strategically designed 4 chamber baffle plate system engineered to create multiple changes in the direction of airflow to cause oil droplets to fall out of suspension, maximizing the efficiency of the PCV air/oil separation.  A dipstick is integrated into the cap so you can monitor the oil level, and the can is easily serviced.  At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil.  The ECS Oil Catch Can is CNC machined from billet 6061-T6 aluminum and with a stealthy black anodized finish for lasting durability and appearance, and includes everything needed for an OEM-like fully reversible installation.  

The ECS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The ECS OCC also has a factory-like appearance. Having a kit designed specifically for your E46 M3 makes for a clean looking setup that any skill level mechanic can install. 

Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles.

*Click here for installation instructions*

ECS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ 4 chamber design promotes excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Anodized black lightweight aluminum
+ Made in USA

This item fits the following BMWs
E46 M3 2001-2006