The main reason all of the VANOS units will eventually fail is because the material used for the sealing rings from the factory is not designed for that type of environment. When this happens the only option that BMW leaves you with is buying a new and expensive VANOS unit with the same sealing rings that failed in your original unit.

The VANOS system found in BMW engines is a great feature (when it’s working properly), keeping your power curve smooth and responsive especially in lower to mid RPM range. What usually goes unnoticed is the gradual loss of power within this range as the vehicle's age due to slowly failing seals within the VANOS unit. The way the VANOS system works is based off of oil pressure triggered by a solenoid that allows for a small range of timing degree adjustment, this is where the power curve is affected. When the seals begin to fail (all of them do) there is less pressure to advance the timing reducing the power in that low to mid range. Because this happens slowly it's very hard to notice a difference until you refresh your VANOS unit, then you easily realize the response you've been missing.

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you're replacing the seals in your VANOS unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy VANOS clatter.

Seals & O-rings:

The seals  were the main focus of this project since the OE units are built with Buna-N rubber o-rings instead of the ECS supplied Viton rubber o-rings. The Buna-N material quickly hardens from the heat and chemical exposure within the engine, where the Viton is significantly more resistant to these chemicals. This knowledge was also used when it came to the commonly failed o-rings found on the VANOS seal plate, replaced at the solenoid.

Rattle Repair:

When it comes to the VANOS rattle this is commonly described as "marbles in a can", and can be heard throughout the different RPM ranges depending on the engine. These upgraded rings and washers are precision ground from hardened steel to resist wear and deformation keeping your VANOS rattle free. The rattle repair tools are designed specifically for this VANOS anti-rattle repair, design from hardened steel to stand up to the job. Designed to perfectly follow the splines of the shaft for a tight grip when applying the necessary torque to disassemble & reassemble the VANOS transfer gear. The keyed socket was designed with the intent to use a "common" wrench so this can be completed at home in your garage.    

When Servicing your VANOS unit we recommend getting everything you need to replace on the way to service which includes an oil change and valve cover gasket set. Fresh oil and gaskets is the best way to start off a fresh rebuild of any kind giving you the maximum performance of your freshly serviced components.

Don't forget to check out our rebuild PDF to make sure you have everything to get the job done and eliminate the rebuild guess work.

This item fits the following BMWs: 
2000-2001 E46 3 Series M3 M3 Convertible 2000-2006 
2001-2002 Z3 Roadster / Coupe Z3 M Roadster Z3 M Coupe w S54 Engine 
2006-2008 E86 E86 Z4 Z4 M Roadster Z4 M Coupe

Drastically improve the looks of your vehicle while improving your vehicle's handling characteristics and/or easily adjust your wheel fitment to allow for the proper clearance when installing parts such as new wheels, big brake kits, or lowering suspension components.Interference from components such as shocks, springs, or control arms are a common issue when installing wheel that are not a direct OE size replacement. By moving your wheels a few millimeters each, you can give yourself enough clearance for proper wheel fitment and give your car a wider stance in the process.

ECS Tuning wheel spacers are constructed of high quality 6061-T6 aircraft grade aluminum and are specifically designed by in-house engineers and cnc machined to exact standards, ensuring the best fitment possible. By carefully measuring the OEM wheel hubs and bore dimensions, these spacers mount with minimal clearance to prevent any vibration, retaining the stock-like vibration free operation. 

This kit includes wheel bolts that are lab tested to meet or exceed ISO 898 class 10.9 mechanical and physical properties to ensure perfect fastening of the wheel to the hub with no issues or potential to snap under aggressive driving conditions.

ECS Tuning is a performance and genuine parts provider that designs their ECS Tuning branded aftermarket automotive parts in-house to ensure the highest quality and affordability possible. Every part's design is subjected to a rigorous test fit and stress test period to guarantee proper fitment and continued reliability for years to come.

This item fits the following BMWs:

2008-2012 E82 BMW 128i 135 1M
​1988-1991 E30 BMW M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2012 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2012 E93 BMW 328i 335i M3 - Convertible
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 530i 535i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5
1982-1989 E24 BMW 633csi 635csi M6
2004-2010 E63 BMW 645ci 650i M6
1981-1987 E23 BMW 733i 735i
1988-1994 E32 BMW 735i 735il 740i 740il 750il
1995-2001 E38 BMW 740i 740il 750il
1990-1999 E31 BMW 840i 840ci 850i 850ci 850csi
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
2009-2016 Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

From years of European automotive experience, the enthusiasts at ECS Tuning have developed a strong understanding of what it takes to produce a quality high-performance brake pad. After thousands of miles and many different pad compounds, they've landed on the ideal blend for the new EP24 "Enthusiast Performance" brake pad! If you're looking for a streetable, track-capable, performance brake pad, look no further than the ECS EP24!

Features & Benefits:

Strong stopping power - Increased coefficient of friction offers satisfying stopping power when cold (a necessity for a street pad!) and even more G-force-inducing power when they warm up. With cold and warm friction comparable to Hawk HPS (and higher than many other street pads) the stopping experience with the EP24 pad is impressive for street-driven vehicles on streetable tires. Positive initial bite - Race pads have the reputation of acting like an on/off switch, which is a no-go for a pad for a street application. The EP24 offers OE-level initial bite for low-stress braking in stop-and-go situations. Reasonable dust - Race pads utilize a high metallic composition. Pads that use high amounts of metal not only dust terribly, but also will bake onto wheels with high temperatures and are a bear to clean. This is not the case with these performance street pads. Now using these pads on most of our shop cars, we’ve found over time that dust is comparable to factory pads in most applications (with greatly improved braking performance). Quiet braking - It’s not a race pad, so it shouldn’t squeal like one. While not as quiet as our ceramic DD23 pad, you’ll still be able to drive your spouse to dinner. Long life - This should be an obvious one. Even in a performance pad, your daily driver pads should last and last, so that was key in selecting our ideal compound. This compound wears slower and is kinder to rotors than two of the top competitors.

EP24 "Enthusiast Performance" brake pads are included in our Lifetime Replacement Program for worry-free motoring.

ECS Tuning Wheel Lock Sets for BMW

Protect your BMW's wheels from theft with ECS Tuning Wheel Lock Sets. These locks offer added security and peace of mind, preventing unauthorized removal of your valuable wheels. With easy installation and a special socket tool included, you can safeguard your investment without costly alterations.

Benefits:

• Enhanced security for your expensive wheels
• Easy installation without the need for costly alterations
• Special socket tool included for convenient removal
• Designed to work with most aftermarket wheels

Revamp your BMW's exhaust aesthetics with the ECS Tuning "Ti.22" Titanium Exhaust Tips, known for their remarkable attractiveness in the market. These exhaust tips showcase a stunning matte titanium finish and a slant-cut, single-wall outlet design, elevating your vehicle's appearance. Engineered for durability, they feature chrome-plated nuts, a 304SS cap screw, and clamp.

Key Benefits:

• Eye-catching matte titanium finish for enhanced aesthetics
• Slant-cut, single-wall outlet for a stylish look
• Durable construction with chrome-plated nuts and 304SS cap screw
• Universal fitment for various vehicles but may require modification for proper installation

Note: Modification might be necessary for proper fitment. This part offers UNIVERSAL fitment and may not directly fit your vehicle. Measuring before ordering is necessary.

From the factory, the E46 M3 featured a dual-mass flywheel and self-adjusting clutch kit. While this provided an easy, comfortable driving experience, it lacks the durability and performance features of an upgraded clutch and flywheel kit. ECS Tuning's all-new S54 performance clutch kit is designed to address these issues. Featuring a full-face clutch disc and heavy-duty pressure plate, this kit offers increased power-holding capability, exceptional pedal feel, and superior durability.

The factory dual-mass flywheel weighs 24.2 lbs. This heavyweight component favors dampened vibrations and smooth gear changes—not performance. The 16.5 lb. E34 M5 flywheel designed by ECS omits the bulky dual-mass design for a single-mass, chromoly steel flywheel. For the performance-minded enthusiast, this translates to quicker RPM changes, easier "heel-toe" downshifts, and improved acceleration.

Engineered in-house with the enthusiast in mind, this is the perfect option for those wanting a lightweight flywheel and performance clutch, without the heavy pedal feel commonly associated with aggressive clutch kits. The ECS S54 performance clutch and lightweight flywheel are designed to accommodate all conditions: from Sunday drives through the country to the abuse of the track. No matter your driving style or ability, this is the flywheel and clutch kit for you.

PART DESIGN

ECS S54 Performance Clutch Kit:

Compatible with any performance flywheel that is designed to accept an E34 M5 architecture clutch Sprung-hub clutch disc Includes ECS performance pressure plate, performance clutch disc, throwout bearing, pilot bearing, alignment tool, and all flywheel and pressure plate hardware ECS Single-Mass Lightweight Flywheel:

Eliminates the factory dual-mass flywheel for: Improved throttle response Improved acceleration Lower replacement cost Hardened 4140 Chromoly Steel for excellent engagement feel and wear resistance Zinc-plated for added corrosion resistance Weighs in at just 16.5 lbs! SFI tested and certified to ensure safe operation under all conditions Why is SFI testing and certification important?

The SFI Foundation, Inc. (SFI) is a non-profit organization established to issue and administer standards for the quality assurance of specialty performance and racing equipment. SFI certification indicates a flywheel has been certified using industry-standard SFI Spec 1.1 standards by an independent testing body to ensure the quality of both design and materials for flywheels utilized in competitive motorsports.

Having successfully passed SFI certification, this flywheel has an individual SFI serial number found in a laser etching, and on an affixed sticker. This certification means the ECS-engineered flywheel is safe and reliable during the rigors of competitive racing; it's also safe and reliable for years and years of street use.

PRODUCT DEVELOPMENT

This Performance Clutch Kit & Lightweight Flywheel was designed, engineered, tested, and quality inspected by the ECS Research and Development team. ECS Tuning strives for the highest level of precision and quality through leading-edge product development technology, including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing an in-house 3D printer, and rigorous long-term product testing.

Turner Motorsport offers an affordable solution to achieve the coveted M3 aesthetic with their M3 replica front bumper. Crafted to genuine specifications, this bumper replicates the M3's look while being made from durable and flexible ABS plastic, ensuring a factory-like fit and finish for your vehicle.

This comprehensive kit includes all necessary components for a complete installation, eliminating the hassle of sourcing individual parts.

Manufactured to high standards by Turner Motorsport, a prominent name in the aftermarket automotive industry, this product undergoes extensive research and testing to guarantee seamless compatibility with your vehicle. Experience the M3 appearance without breaking the bank, as this bumper has been designed to deliver top-notch quality at an affordable price.

Included Components:

• M3 Bumper Cover
• Lower Grille
• Fog Lights and Trim

Note: Fog lights necessitate sourcing and splicing in of 9006 connectors

From years of European automotive experience, the enthusiasts at ECS Tuning have developed a strong understanding of what it takes to produce a quality high-performance brake pad. After thousands of miles and many different pad compounds, they've landed on the ideal blend for the new EP24 "Enthusiast Performance" brake pad! If you're looking for a streetable, track-capable, performance brake pad, look no further than the ECS EP24!

Features & Benefits:

Strong stopping power - Increased coefficient of friction offers satisfying stopping power when cold (a necessity for a street pad!) and even more G-force-inducing power when they warm up. With cold and warm friction comparable to Hawk HPS (and higher than many other street pads) the stopping experience with the EP24 pad is impressive for street-driven vehicles on streetable tires. Positive initial bite - Race pads have the reputation of acting like an on/off switch, which is a no-go for a pad for a street application. The EP24 offers OE-level initial bite for low-stress braking in stop-and-go situations. Reasonable dust - Race pads utilize a high metallic composition. Pads that use high amounts of metal not only dust terribly, but also will bake onto wheels with high temperatures and are a bear to clean. This is not the case with these performance street pads. Now using these pads on most of our shop cars, we’ve found over time that dust is comparable to factory pads in most applications (with greatly improved braking performance). Quiet braking - It’s not a race pad, so it shouldn’t squeal like one. While not as quiet as our ceramic DD23 pad, you’ll still be able to drive your spouse to dinner. Long life - This should be an obvious one. Even in a performance pad, your daily driver pads should last and last, so that was key in selecting our ideal compound. This compound wears slower and is kinder to rotors than two of the top competitors.

EP24 "Enthusiast Performance" brake pads are included in our Lifetime Replacement Program for worry-free motoring.

From years of European automotive experience, the enthusiasts at ECS Tuning have developed a strong understanding of what it takes to produce a high-quality brake pad. After thousands of miles and many different pad compounds, they've landed on the ideal blend for the new DD23 "Daily Driver" brake pad! This enthusiast-developed pad offers confident stopping power, very low dust, quiet braking, and a positive initial bite. The perfect choice for your daily-driven Euro!

If you find yourself “pumping the brakes” over the brake pad selection process for your daily driver, your answer is this DD23 pad. This is the one!

As a team of enthusiasts who own all types of European cars, we have the advantage of the exposure that comes with the enthusiast lifestyle - and have a strong understanding of what makes a great brake pad. In the pursuit of a really great brake pad for daily driving, we’ve tested a wide range of brake pads. After thousands of test miles, iterating through a variety of pad compounds, we’ve landed on the ideal blend for our DD23 Daily Driver ceramic pad.

Features:

Good stopping power - Brake pads need to stop your car, period, so this is key. We focused on selecting a compound that offers a healthy level of friction (both when hot and when cold) for safe, positive stopping power.

Positive initial bite - You should feel your brakes engage as you press the pedal, but it should not feel like an on/off switch! Advanced ceramic composition means you’ll enjoy a smooth transition on and off of the brake pedal, meaning your passengers will have a comfortable ride in stop-and-go traffic. We’ve hit a good balance here.

Very low-dust - Some factory-installed pads are eye-poppingly dusty, which is a no-go for us. Thanks to the composition of this ceramic pad, which is copper-free and contains a negligible amount of other metals, dust is both lighter in color and very limited in amount. We’ve improved on the “dust factor” without sacrificing on bite and stopping power as a good compromise, which will be a win for anyone who doesn’t detail daily (or anyone who does, too!)

Quiet braking - It’s not a race pad, so it shouldn’t squeal like one. Extremely low metallic composition means they will not squeal. DD23 is comfortable and quiet - both on the ears and in lack of vibration transmitted through the cabin.

Long life - This should be an obvious one. Your daily driver pads should last and last, so that was key in selecting our ideal compound. This is another benefit to having ceramic material composition versus a softer organic pad (which have higher metallic and various organic elements) and wear much faster. Ours are kind to rotors, too (no accelerated wear characteristics) for many miles of motoring.

Drastically improve the looks of your vehicle while improving your vehicle's handling characteristics and/or easily adjust your wheel fitment to allow for the proper clearance when installing parts such as new wheels, big brake kits, or lowering suspension components.Interference from components such as shocks, springs, or control arms are a common issue when installing wheel that are not a direct OE size replacement. By moving your wheels a few millimeters each, you can give yourself enough clearance for proper wheel fitment and give your car a wider stance in the process.

ECS Tuning wheel spacers are constructed of high quality 6061-T6 aircraft grade aluminum and are specifically designed by in-house engineers and cnc machined to exact standards, ensuring the best fitment possible. By carefully measuring the OEM wheel hubs and bore dimensions, these spacers mount with minimal clearance to prevent any vibration, retaining the stock-like vibration free operation. 

ECS Tuning is a performance and genuine parts provider that designs their ECS Tuning branded aftermarket automotive parts in-house to ensure the highest quality and affordability possible. Every part's design is subjected to a rigorous test fit and stress test period to guarantee proper fitment and continued reliability for years to come.

This item fits the following BMWs:

2008-2012 E82 BMW 128i 135 1M
1988-1991 E30 BMW M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2012 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2012 E93 BMW 328i 335i M3 - Convertible
1976-1981 E12 BMW 528i 530i
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 530i 535i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5
1982-1989 E24 BMW 633csi 635csi M6
2004-2010 E63 BMW 645ci 650i M6
1981-1987 E23 BMW 733i 735i
1988-1994 E32 BMW 735i 735il 740i 740il 750il
1995-2001 E38 BMW 740i 740il 750il
1990-1999 E31 BMW 840i 840ci 850i 850ci 850csi
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
2009-2016 Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

Rear Only
2007-2013 E70 BMW X5M
2007-2014 E71 BMW X6 xDrive35i X6 xDrive50i X6M

Enhance your BMW's handling prowess with ECS Tuning's Carbon Fiber Strut Tower Bar. This lightweight and incredibly rigid strut bar kit braces the shock towers together, preventing flex and alignment changes during aggressive driving. Crafted from carbon fiber, it not only offers a lightweight solution but also adds an attractive touch to your engine bay.

• Prevents strut tower flex and alignment changes during aggressive driving
• Lightweight and rigid carbon fiber construction
• Adds a unique and stylish look to your engine bay
• High gloss carbon fiber bar with silver CNC machined tower plates and stainless steel hardware
• Not compatible with SULEV M56 engine models

For optimal performance, consider the 46.5mm To 61.0mm Silicone Coupler.

Engineered with durability and functionality in mind, this silicone coupler provides a reliable connection for various components in your vehicle's intake or cooling system. Its smooth interior surface promotes efficient airflow, while its flexible and reinforced construction ensures a secure fit and prevents leaks. Enjoy hassle-free installation and enhanced performance with this premium silicone coupler.

• Durable silicone construction
• Smooth interior surface for efficient airflow
• Flexible and reinforced design prevents leaks
• Secure fit for reliable performance
• Hassle-free installation

Looking for the most attractive and adjustable tip on the market? Look no further than our ECS Swivel Exhaust Tips!

Featuring a unique swivel collar design that allows the tip to be adjusted in any direction to achieve that perfect fitment. Simply adjust the tip to your desired position and tighten the hex bolt to 14 ft-lbs (19 Nm) and the tip will stay where positioned.

Every ECS Exhaust Tip comes with a precision laser etched ECS Tuning logo and features a slant cut, double wall, rolled edge for a stunning appearance! These are engineered to last, featuring chrome plated nuts, 304SS cap screw, clamp, insert ring and exhaust tip.

Available in 3.5" or 4.0" outlet and chrome or black chrome finish.

Dimensions:

Inlet Size: 2.50"
Overall Length: 7.0"
Outlet Size: 3.50"
Outlet Style: Double Wall, Rolled Edge, Slant Cut
**Modification may be required for proper fitment.**