BMW Suspension Parts for BMW 1 Series E82 (2008-2013)

The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

This coilover kit fits the following BMWs:
2008+ E82 BMW 128i 135i
2006+ E90 BMW 325i 328i 330i 335d 335i
2007+ E92 BMW 328i 335i 335is
2007+ E93 BMW 328i 335i

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

Our E90 E92 E93 fixed camber plates are designed from the knowledge we gained from our highly successful racing campaigns with the E46 in the Speed World Challenge series. Our camber plates are offset for the best camber and caster combination for racing purposes when using the stock-diameter sized springs. Camber increases to -2.5° depending on your individual suspension setup, while only increasing ride height by 6mm. The rate of camber change is virtually unaffected throughout the range of suspension travel, reducing the need for other geometry correction. Fixed mount camber plates are legal in many racing and autocross classes - these are the perfect camber solution when adjustable plates are not allowed in your class.

These are very simple to install, requiring only pressing out locator dowels and studs in your factory strut mounts. See below for detailed instructions.

A BMWs sub-frame is the heart of the suspension - as the subframe twists and shifts under load all of the suspension mounting points also move. The rear suspension feels loose and lacks precision. As rubber or hydroelastic bushings wear the bushing deflection gets worse. If you have a highly tuned 335i/xi you're putting even more strain on weak bushings. The solution is a stiffer and more durable material. Even BMW has moved to solid mounts on the F10 M5 and F8X M3/M4. These fully solid E82/E90/E92 aluminum mounts have zero deflection - the subframe does not move at all. The rest of the suspension can work as designed and maintain the proper alignment and motion ratios. The driver will notice the difference as the car is more stable and the handling is more precise.

Although we designed these for use in our racecars, they can work on the street so long as the driver can tolerate some additional noise, vibration, and harshness. These mounts are CNC machined in the USA and made with high-grade aluminum. The set is for all four subframe mounts.

These solid rear sub frame mounts fit: 
2008-2012 E82 BMW 128i 135i 
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan 
2006-2011 E91 BMW 325i 328i - Wagon 
2007-2012 E92 BMW 328i 335i 335is - Coupe 
2007-2012 E93 BMW 328i 335i - Convertible 

Rubber mounts in any position of a vehicle are usually designed with comfort and longevity in mind leaving performance as a sacrifice. This kind of sacrifice here at Turner just won't do, so we did what we do best and designed a solid monoball mount.

Our engineering team first wanted to tackle the issue with wear found on rubber mounts. Due to their combination of steel, rubber, and low mounting location, these mounts are a direct target for deterioration and failure. As they are positioned out in the open and exposed to the elements, bonded steel and rubber components inevitably hold moisture, separating as the steel bearing begins to rust. Our solution was to offer a rebuildable mount with a Teflon lined bearing for increased durability, combined with a blue anodized body and melonite coated bushing sleeves for corrosion resistance.

The performance side of these mounts is primarily found in the articulation allowed by the bearing. Rubber mounts do not allow for proper free damper movement, hindering shock performance. By eliminating the deflection found in factory rubber mounts and allowing full shock articulation, this solid monoball design eliminates slop and maximizes shock efficiency and performance, allowing for more predictable handling on the street or the track - with almost zero added noise, vibration, and harshness.

Replaces OE part #: 33526768544

Key Benefits:

• Monoball rear lower shock mount eliminates unwanted deflection, maximizing shock efficiency and performance.
• Allows full shock body articulation for low friction movement and reduced side loading and improved shock wear.
• Designed to work with stock non-M taper seat stud style shocks (not M eyelet mount type).
• Maintains OE shock position

Design features:

• Rebuildable using off the shelf bearings - these are the last rear shock mounts you’ll need to buy
• Includes new hardware
• Made in USA

Housing:

• Billet CNC 6061-T6 aluminum housing, type II anodized for exceptional durability and corrosion resistance

Bearing:

• FK WSSX14T teflon lined spherical bearing
• 440C heat-treated stainless steel ball, 1 ⅜” ball dia.
• 17-4 PH heat-treated stainless steel race
• Self-lubricating PTFE liners are chemically bonded to the inner diameter of the race to offer a very high load-carrying capacity with greatly increased dynamic wear characteristics.
• Static Axial Load Rating: 10,800 lbs.
• Rod End Misalign Angle: 6 degrees

Bearing inserts:

• CNC machined 1144 steel, heat treated and melonite coated designed to maximize ball articulation while offering exceptional durability and corrosion resistance.

This item fits the following BMWs: 
2008-2013 E82 BMW 128i 135i 135is Coupe 
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan 
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon 
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe 
2007-2013 E93 BMW 328i 335i 335is - Convertible 

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. Genuine BMW bushings are the perfect option to restore suspension back to day 1 quality.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Genuine BMW Rubber Mounting Front -
This item fits the following BMW Chassis:
E82,E90,E92,E93

If you are looking to upgrade your front sway bar, this M Sport sway bar is a great option! The increased diameter and stiffness will add a significant handling boost to your vehicle without affecting reliability.

Genuine BMW Stabilizer Front With Rubber Mounting -
This item fits the following BMW Chassis:
E82,E90,E92,E93