BMW Internal Engine Parts for BMW 3 Series E92 (2007-2013)

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

E9x M3 BE Bearings Performance Rod Bearing Replacement Kit

T#:5403237

Part#: 11247838088TMSKT

In Stock

$ 1,106.99

This product was last offered at the strikethrough price on
07-20-2026

$ 1,105.99 USD

Add to Wish List

Qty

$ 1,105.99 USD

Add to Wish List

Includes everything needed for a rod bearing service, featuring BE Bearings upgraded rod bearings. The S65 engine has a known history of rod bearing failure, and if your engine is higher mileage, don't let this catastrophic failure happen to you. Replace your rod bearings and prevent a spun bearing which can trash your crankshaft. BE Bearings, in conjunction with Clevite, an OE bearing manufacturer, have redesigned and manufactured the bearings for greater clearance and have changed the original material composition from tin-aluminum to lead-copper. This upgrade incorporated the state-of-the-art Clevite Tri-Metal design and featured a Tri-Armor™ coating. This allows for the additional lubrication for wear prevention, plus, the softer bearings are better for your engine and are more tolerant of foreign particles suspended in your oil. Another benefit from this is that the oil can now be sent for testing to accurately gauge the amount of wear occurring in the engine. Kit includes Upper and lower BE Bearings upgraded rod bearings Hardware Oil filter Castrol TWS Edge Professional 10W 60 Oil pan gasket RedLine assembly lube

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

T#:558795

Part#: VTT-CRANKHUB-1

Ships in 1-2 days

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

N52 Valvetronic Camshaft Adjuster Replacement Kit

T#:5416764

Part#: 11377548388TMSKT

Ships in 6 Business Days

Sale - Save 19% $ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.20 USD

Add to Wish List

Qty

Sale - Save 19%

$ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.20 USD

Add to Wish List

Includes new Valvetronic motor, gasket, and hardware. The Valv-tronic adjuster unit changes the the timing shaft to adjust the valve timing.

Rod Bearing Overhaul Kit - E9X M3 S65

T#:340426

Part#: TMS222795

Ships in 2 Business Days

$ 1,530.99

This product was last offered at the strikethrough price on
02-26-2026

Starting at $ 1,456.40 USD

Add to Wish List

Starting at $ 1,456.40 USD

Add to Wish List

Rod bearings should be replaced as a preventative measure before 80,000 miles. This package is the most complete rod bearing overhaul kit available and includes not just the latest BMW rod bearings and connecting rod bolts, but also everything else that should be replaced with the oil pan and front subframe off the car.

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

T#:18733527

Part#: VTT-CRANKHUB-2

Ships in 10 Business Days

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Cam Bearing Ledge Replacement Kit - N54

T#:640352

Part#: 11127531224KT2

In Stock

$ 1,641.21 USD

Add to Wish List

Qty

$ 1,641.21 USD

Add to Wish List

Over time the bearing ledges in your N54 can be damaged by contaminated oil or a malfunctioning VANOS which can cause grooves to form in the bearing ledges. This kit contains everything necessary to replace these as well as important hardware.

Show More Show Less

N55 Turbo Install Kit

T#:401612

Part#: 18407502196KT2

In Stock

$ 290.99 USD

Add to Wish List

Qty

$ 290.99 USD

Add to Wish List

BE Bearings Performance Rod Bearing Replacement "Dry" Kit - E9x M3 W/...

T#:9868817

Part#: 11247838088DR2KT

Ships Today

$ 974.33

This product was last offered at the strikethrough price on
07-20-2026

$ 973.82 USD

Add to Wish List

Qty

$ 973.82 USD

Add to Wish List

NOTE: This is a Dry kit and does not include engine oil. See our catalog for all engine oil options! Includes everything needed for a rod bearing service, featuring BE Bearings upgraded rod bearings. The S65 engine has a known history of rod bearing failure, and if your engine is higher mileage, don't let this catastrophic failure happen to you. Replace your rod bearings and prevent a spun bearing which can trash your crankshaft. BE Bearings, in conjunction with Clevite, an OE bearing manufacturer, have redesigned and manufactured the bearings for greater clearance and have changed the original material composition from tin-aluminum to lead-copper. This upgrade incorporated the state-of-the-art Clevite Tri-Metal design and featured a Tri-Armor™ coating. This allows for the additional lubrication for wear prevention, plus, the softer bearings are better for your engine and are more tolerant of foreign particles suspended in your oil. Another benefit from this is that the oil can now be sent for testing to accurately gauge the amount of wear occurring in the engine. Kit includes Upper and lower BE Bearings upgraded rod bearings Hardware Oil filter Oil pan gasket RedLine assembly lube

Show More Show Less

E9X S65 WPC Performance Rod Bearing Replacement Kit

T#:7260312

Part#: S65WPCDKT

Ships Today

Sale - Save 2% $ 1,394.99

This product was last offered at the strikethrough price on
05-03-2026

$ 1,370.29 USD

Add to Wish List

Qty

Sale - Save 2%

$ 1,394.99

This product was last offered at the strikethrough price on
05-03-2026

$ 1,370.29 USD

Add to Wish List

Vargas "Spline Lock" Crank Hub Solution - N54

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

T#:18733526

Part#: VTT-CRANKHUB-4

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

VTT N54 “Spline Lock” CrankHub Solution Package W/ Crank Bolt Cap...

T#:19395579

Part#: VTTCRANKHUBPKG

Ships in 10 Business Days

$ 934.99 USD

Add to Wish List

Qty

$ 934.99 USD

Add to Wish List

VTT is proud to offer the only complete N54 complete crank hub solution that does NOT require the crank to be drilled for pins. Our hub uses our proprietary “Spline Lock” technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). We spent many months testing, and retesting this design, utilizing well over 10 different samples to come to our final production version. During testing, our final hub managed to break our testing rig before slipping. These have been bench tested, and real-world tested on the VTT N54 race car spinning 8K RPM and making well over 900WHP. This technology means our hub installs the same as a stock hub, no drilling of the crank, which means MUCH less labor is involved and is reversible is ever wanting to be uninstalled leaving no holes in the crank. The “Spline Lock” is ONLY available with the VTT Crank bolt capture for the ULTIMATE Crank Hub solution for your BMW. These parts are designed to be used together, and the spline lock should not run without the CBC VTT “Spline Lock” Crank hubs are CNC manufactured from 440C tool Steel with a Rockwell rating of HRC60 for the ultimate in durability, and toughness. Hub Plus OEM bolt OEM Oil pump sprocket OEM oil sprocket retainer VTT Crank bolt capture

Show More Show Less

N54 Crank Hub Service Kit - Up To 02/2011

For vehicles with production date up to 02/2011

T#:2227021

Part#: N54PRCRANKT

In Stock

Sale - Save 4% $ 156.99

This product was last offered at the strikethrough price on
05-03-2026

$ 151.49 USD

Add to Wish List

Qty

Sale - Save 4%

$ 156.99

This product was last offered at the strikethrough price on
05-03-2026

$ 151.49 USD

Add to Wish List

All of the components necessary for service when upgrading to an aftermarket crank hub solution.

E9X M3 Rod Bearing Set

T#:340427

Part#: TMS222796

In Stock

Starting at $ 847.99 USD

Add to Wish List

Starting at $ 847.99 USD

Add to Wish List

Rod bearings should be replaced as a preventative measure before 80,000 miles. This is the set of rod bearings for the S65 V8 in the E90/E92 M3 (BMW part numbers 11247841703 and 11247841702). This is just the set of bearings and does not include any of the other items that need to be replaced at the same time (connecting rod bolts, oil pan gasket, hardware, etc).

Show More Show Less

S65 WPC Performance Rod Bearing Replacement Kit

Stronger & smoother, with less friction!

T#:5498491

Part#: S65WPCKT

Ships Today

Sale - Save 1% $ 1,583.99

This product was last offered at the strikethrough price on
05-03-2026

$ 1,561.76 USD

Add to Wish List

Qty

Sale - Save 1%

$ 1,583.99

This product was last offered at the strikethrough price on
05-03-2026

$ 1,561.76 USD

Add to Wish List

The S65 engine has a known history of rod bearing failure, and if your engine is higher mileage, don't let this catastrophic failure happen to you. Replace your rod bearings and prevent a spun bearing which can trash your crankshaft. What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both. What are you waiting for? Use WPC-treated bearings on your next engine build or rod bearing service! Kit includes Upper and lower WPC Treated Genuine BMW Rod Bearings Hardware Oil filter Castrol TWS Edge Professional Oil pan gasket RedLine assembly lube

Show More Show Less

N54 Spline Lock Crank Hub Solution With Complete Package

T#:18733525

Part#: VTT-CRANKHUB-3

Ships in 10 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

N54 Crank Hub Service Kit - From 02/2011

For vehicles with production date from 02/2011

T#:2227020

Part#: N54POCRANKT

In Stock

Sale - Save 3% $ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 146.41 USD

Add to Wish List

Qty

Sale - Save 3%

$ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 146.41 USD

Add to Wish List

All of the components necessary for service when upgrading to an aftermarket crank hub solution.

Project Cars

SELECT YOUR BMW

BMW Internal Engine Parts for BMW 3 Series E92 (2007-2013)

Sub-Categories

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

E9x M3 BE Bearings Performance Rod Bearing Replacement Kit

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

N52 Valvetronic Camshaft Adjuster Replacement Kit

Rod Bearing Overhaul Kit - E9X M3 S65

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

Cam Bearing Ledge Replacement Kit - N54

N55 Turbo Install Kit

BE Bearings Performance Rod Bearing Replacement "Dry" Kit - E9x M3 W/...

E9X S65 WPC Performance Rod Bearing Replacement Kit

Vargas "Spline Lock" Crank Hub Solution - N54

Spline Lock Crank Hub Solution W/ Hardware Package - N54

Spline Lock Crank Hub Solution

VTT N54 “Spline Lock” CrankHub Solution Package W/ Crank Bolt Cap...

N54 Crank Hub Service Kit - Up To 02/2011

E9X M3 Rod Bearing Set

S65 WPC Performance Rod Bearing Replacement Kit

N54 Spline Lock Crank Hub Solution With Complete Package

N54 Crank Hub Service Kit - From 02/2011

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results