BMW Suspension Parts for BMW 3 Series E92 (2007-2013)

The rear lower control arms on E82/E9X models are the weakest link in the rear suspension. The arm is made from folded sheetmetal and it bends and deforms easily. Not only will it deform from potholes and curbs, tow truck drivers love to hook onto them without realizing how weak they are. We have seen other race teams complete the box section to make them stronger. A bent arm will throw off the geometry in the suspension, potentially affecting handling and tire wear. These aluminum arms are both lighter and stronger than the factory sheetmetal arms and is the best solution for chronic bending of the stock arm. These are a direct replacement to your stock arms with no changes needed to your alignment. New high-grade hardware is included.

Note: the stock arm is designed from the factory to be intentionally weak. These arms will bend so that something else in the suspension does not break. Our race cars used the stock sheetmetal arm but we replaced them often. We found that it was better to finish a race with a bent arm than not finish due to a catastrophic failure. The ECS arms are still designed to be the weakest link but are far stronger than the factory arm and will not bend as easily.

This item fits the following BMWs:

2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335i 335xi M3 - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi M3 - Coupe
2007-2013 E93 BMW 328i 335i 335is M3 - Convertible

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 255mm (10") to 315mm (12.4") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints (M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability NOTE: If you've modified your vehicle's suspension with aftermarket struts or coilovers, the mounting location for the sway bar end link may have moved. To confirm fitment with our adjustable end links, please measure the distance between the sway bar and the mounting location on the strut body with the vehicle at ride height and confirm that it is within the 255 mm - 315mm range of adjustment.

Enhance the performance and aesthetics of your BMW with the ECS Wrinkle Black Strut Tower Bar Kit. This kit not only adds a stylish wrinkle black finish but also reduces chassis flex, stiffening the suspension for improved handling. Triangulating the front end ensures more consistent suspension geometry, enhancing overall stability.

• Wrinkle Black Strut Tower Bar Kit for BMW
• Stylish appearance with wrinkle black finish
• Reduces chassis flex for improved suspension
• Triangulates the front end for consistent suspension geometry
• Enhances overall stability and handling

BMW E9X M3 Supplementary Ride Quality & Handling Kit enhances the performance of your BMW by working in conjunction with Dinan performance springs. This kit is designed to improve handling while maintaining superior ride quality. It includes:

• Progressive-Rate Bump Stops: Optimizes suspension travel, preventing bottoming out and binding.
• Enhanced Mechanical Grip: Improves spring rate for better handling.
• Maximized Suspension Travel: Allows for more effective use of suspension capabilities.
• Prevents Bottoming Out and Binding: Ensures a smooth and controlled driving experience.
• All Hardware Included: Simplifies installation with included uprated strut mounts.
• Dinan Badge Points: Earns 1 point toward the Dinan badge.

For over 35 years, Dinan has been a leading name in BMW tuning, known for balancing enhanced performance with the original driving character of BMW vehicles. The Dinan kit comes with a four-year, 50,000-mile warranty, reflecting their commitment to quality and durability.

BMW E92 M3 Performance Spring Set is engineered to elevate your driving experience by using increased spring rates that reduce body roll and enhance handling dynamics. This performance spring set lowers your vehicle's center of gravity slightly, providing a balanced stance without sacrificing daily driving comfort.

• Reduced Body Roll: Experience improved stability and control during cornering.
• Enhanced Braking Performance: Minimized dive under braking for more precise stops.
• Improved Grip: Better tire contact with the road for increased traction.
• Slight Lowering: Lowers the vehicle by approximately 1/2 inch for a sportier appearance.
• Durability: Springs are preset to prevent sag and are shot-peened for stress relief.
• Dinan Badge Points: Earn 2 points toward your exclusive Dinan badge.

For over 35 years, Dinan has led the way in BMW tuning, focusing on balanced performance that maintains the original driving feel of your BMW. Each part is meticulously developed, tested, and backed by a four-year, 50,000-mile warranty. As you enhance your BMW with Dinan's high-quality components, you move closer to earning the prestigious Dinan badge, a symbol of superior BMW performance.

The camber plates improve on the amount of adjustment and fine-tuning available in the front suspension to improve mechanical grip while cornering. Made to the same quality you'd expect from Dinan and BMW, they help to fine-tune the right amount of camber for Dinan springs.

• Improved mechanical grip
• Reduced understeer
• Works great with Dinan springs
• Worth 1 point toward your Dinan badge

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere.

This item fits the following BMWs: 

2008-2013 BMW M3 

Dinan Performance Springs are matched to your BMW's chassis and suspension components to deliver better handling and looks without sacrificing ride quality. Dinan BMW springs are carefully engineered to work within your car's suspension travel and to improve suspension geometry. Spring rates are slightly stiffer than stock and dialed in to reduce bodyroll. A stiffer suspension makes the car more fun to drive and the lower ride height improves the looks by reducing wheel-fender gap.

Dinan spring specs -

• F: -1/2" (12mm)
  
• R: 0" (0mm)

Fitment note: When used with stock shocks the Dinan Ride Quality Kit is strongly recommended. The Kit consists of shorter and stiffer bump stops and spring perches that work better with the lowered ride height of these springs. While not explicitly required, less than favorable ride quality and handling may result without them.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. The springs are worth 2 points towards your Dinan badge (Ride Quality Kit is worth 1 point).

This item fits the following BMWs:
2007-2013 E92 BMW 335i 335is 335xi - Coupe

Elevate the performance of your BMW with Turner Motorsport Performance Springs, designed to reduce body roll and enhance handling. These springs feature increased spring rates for improved grip and a slight lowering to lower the vehicle's center of gravity without sacrificing street usability or comfort. Experience reduced dive under braking and squat under acceleration for a more controlled driving experience. Here are the key benefits:

• Reduced body roll for tighter handling
• Decreased dive under braking
• Enhanced grip for improved performance
• 1/2" front lowering without compromising rear comfort
• Preset to prevent spring sag
• Shot-peened for stress relief and durability
• Worth 2 points toward your Dinan badge

For over 35 years, Turner Motorsport has been at the forefront of BMW tuning, offering meticulously developed and tested parts that preserve the original driving feel while enhancing performance. Backed by a four-year, 50,000-mile warranty, Turner Motorsport ensures quality and reliability in every product.

Correct toe settings contribute to both stable steering and even tire wear. The SPC Performance wheel toe bar tool is designed to prevent vehicle drifting and ensure uniform tire wear. It includes a steel bar equipped with sliding adjusters and pointers to accurately assess the vehicle's toe alignment.

For wider wheel bases use T#386442!