BMW Brakes & Brake Parts for BMW 3 Series E92 (2007-2013)

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Turner has developed a new zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner Stainless brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

RSL19 A favorite of BMW's Motorsport engineers, the Pagid RSL19 compound is an endurance pad based on the RS14 Black but with less friction to improve modulation and low pedal effort. These pads work best in a heat range up to 1,100* F. The combination of friction levels, fade stability, and long life for pads and rotors makes this a favorite for club and HPDE drivers. 

This is the set of Rear pads.

This item fits the following BMWs:
2004-2010 E60 BMW 535i 545i 550i M5
2004-2011 E63 E64 BMW 645ci 650i M6
2011+ E82 BMW 1M - Coupe
2008-2013 E90 BMW M3 - Sedan
2008-2013 E92 BMW M3 - Coupe
2008-2013 E93 BMW M3 - Convertible

The RSL29 pad is an endurance racing compound with long life and great wear characteristics. It has stable friction over a broad temperature range which makes them a very easy to use and predictable braking pad in a lot of environments. An evolution of the RSL19 endurance pad designed for more advanced drivers. This compound combines the outstanding wear rate of the RSL19 with a slightly higher coefficient of friction and initial bite. RSL29 also features improved hot fade resistance over the RSL19. In addition to the endurance racing, this pad will also be found in GT and VLN classes and Touring Cars (including our own E46 World Challenge cars). BMW has been using Pagid Yellow pads on their Nurburgring test vehicles and Ring Taxi for years.

This is the set of Rear pads.

This item fits the following BMWs:
2004-2010 E60 BMW 535i 545i 550i M5
2004-2011 E63 E64 BMW 645ci 650i M6
2011+ E82 BMW 1M - Coupe
2008-2013 E90 BMW M3 - Sedan
2008-2013 E92 BMW M3 - Coupe
2008-2013 E93 BMW M3 - Convertible

The latest in the Yellow line takes all of the RSL29 characteristics and adds a bit more aggressive behavior. Friction levels go up for more initial bite and better fade resistance. Modulation and release stays close to RSL29 levels. Pad and rotor wear is a little more than on the previous Yellows but still within reasonable levels and the RSL1 is still considered an extended endurance pad. Its development stemming from GT classes at Le Mans and Nürburgring.

Since Pagid pads tend to "out-gas" we recommend using these pads with a new gas-slotted or cross-drilled rotor for the best performance. Pagid brake pads are not compatible with previously used rotors, especially if used with a carbon or Kevlar based race pad.

This item fits the following BMWs:
2008-2013 E82/88 BMW 135i, 128 with BMW Performance caliper conversion
2006-2009 E9X BMW Submodels with BMW Performance caliper conversion

RSL19 A favorite of BMW's Motorsport engineers, the Pagid RSL19 compound is an endurance pad based on the RS14 Black but with less friction to improve modulation and low pedal effort. These pads work best in a heat range up to 1,100* F. The combination of friction levels, fade stability, and long life for pads and rotors makes this a favorite for club and HPDE drivers. 

This is the set of FRONT pads.

This item fits the following BMWs:
2011+ E82 BMW 1M Coupe
2004-2005 E60 BMW 525i (automatic transmission only)
2006-2007 E60 BMW 525i, 525xi (all transmissions)
2008-2010 E60 BMW 528i, 528xi
2004-2007 E60 BMW 530i, 530xi
2008-2010 E60 BMW 535i, 535xi
2004-2010 E60 BMW 545i, 550i
2004-2010 E63 BMW 645Ci, 650Ci
2002-2008 E65 BMW 745i, 745Li, 750i, 750Li, 760Li
2007-2013 E9X BMW 335i, 335Xi, 335d
2008-2013 E9X BMW M3

The latest in the Yellow line takes all of the RSL29 characteristics and adds a bit more aggressive behavior. Friction levels go up for more initial bite and better fade resistance. Modulation and release stays close to RSL29 levels. Pad and rotor wear is a little more than on the previous Yellows but still within reasonable levels and the RSL1 is still considered an extended endurance pad. Its development stemming from GT classes at Le Mans and Nürburgring.

Since Pagid pads tend to "out-gas" we recommend using these pads with a new gas-slotted or cross-drilled rotor for the best performance. Pagid brake pads are not compatible with previously used rotors, especially if used with a carbon or Kevlar based race pad.

This item fits the following BMWs:
2008-2013 E82/88 BMW 135i, 128 with BMW Performance caliper conversion
2006-2009 E9X BMW Submodels with BMW Performance caliper conversion