Select Vehicle
BMW
Mini
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
If there was a Top 5 list of things to do on the E46 M3, a shorter gears would be in the top two... The gearing used to be overlooked when planning modifications but the 3.91 and 4.10 gears are now one of our biggest selling upgrades for the E46 M3! With a rear end gear upgrade you get the effects of adding horsepower but without adding any more stress to the engine or drivetrain. The R&P acts as a torque multiplier, getting you into the power band sooner in each gear. It's one of the best areas to get return from your modification spending. The shorter (numerically higher) rear end gears will give you better acceleration in all gears at any speed with few downsides. Want to make your car faster off the line or out of corners? Or avoid a downshift to pass on the highway? This is what you need. This 4.10 is the latest version from BMW Motorsport - shot peened and hardend for increased strength. The R&P can be installed on its own but for cars that have more than 60,000 miles it would be a better idea to rebuild the whole diff. The factory viscous limited slip units have a typical lifespan of 50-70,000 miles. We offer diff rebuilding with 4.10 or other gear options and you get a fully-rebuilt and serviced limited slip unit at the same time. Click here for our diff rebuild options.
4.10 Gearing Example: 2004 M3, 6-speed manual, 275/35-19" rear tires
Gear RatioGearSpeedRPM
40 MPH in 4th
3.62 4th 40mph 2,250rpm
4.10 4th 40mph 2,550rpm
70 MPH Cruise
3.62 6th 70mph 2,650rpm
4.10 6th 70mph 3,000rpm
5th Gear Speed at Redline
3.62 5th 175mph 8,000rpm
4.10 5th 154mph 8,000rpm
Why 5th? Because 6th does not have the mechanical advantage to get past wind resistance at these speeds - it is more of a cruise/overdrive gear. Using 5th for comparison purposes is much more relevant than having to take into account wind direction, resistance, grade, elevation, tire sizing, etc. These numbers are for comparisons among gear ratios only, not to determine what your M3 will top out at.
This item is the genuine BMW part and the ring & pinion set only. You will need to have this professionally installed into your existing differential. BMW does not supply differential rebuild parts (bearings, shims, plates, etc.) so only a qualified shop that is experienced in BMW diff rebuilding should perform this installation. We also offer built differentials and exchanges, click here.
This item fits the following BMWs:
2001-2006 E46 BMW M3
2004-2010 E60 BMW M5 (manual transmission only)
OEM part number 33108321899
Advanced Clutch Technology (ACT) designs, engineers and develops products by leveraging decades of track and performance street experience. Advanced CAD, FEA simulation, and CAM tools help ensure highly optimized performance, reliability, and repeatability. These key advantages are produced by combining the best engineering and design methodologies with the latest in materials and manufacturing techniques.
ACT clutch kits stand unequaled in terms of consistent pedal feel, high torque capacity, long wear life and durability. In-house manufacturing is critical in tuning components specifically to each individual application while maintaining the predictable ACT pedal feel across the entire catalog.
This clutch kit features an Xtreme pressure plate, a Performance Street sprung clutch disc, and an XACT Streetlite Flywheel.
Their Xtreme pressure plate offers a 50-120% clamp load increase, moderate to heavy pedal feel, and is recommended for high performance street and racing applications. All diaphragms went through a four stage heating process for increased strength and unparalleled performance.
Next in this kit is the Performance Street clutch disc. This is the most popular sprung clutch disc and features high quality organic friction material with a high copper content for improved heat transfer and a steel backed lining for increased strength in burst load circumstances. This organic clutch disc has a significantly higher torque capacity than a stock disc but still retains a long life span and operates quietly and reliably.
Clutch Kit Specs:
This kit from Valeo is a simple way to easily convert your stock dual mass flywheel clutch system to a single mass system.
Dual mass flywheels allow for fluid-feeling clutch engagements and offer a more luxurious feel than single-mass flywheels. However, with these benefits come significant drawbacks. Why convert from a dual-mass flywheel to a single-mass flywheel?
Cost: Dual-mass flywheels are expensive, with the cost of replacement often times being double or triple than that of converting to a single-mass flywheel.
Serviceability: Single-mass flywheels can be resurfaced, eliminating the need to replace with the next clutch service. - something that is not recommended with dual-mass flywheels, as they contain a rubber section that is more failure-prone in high mileage application.
Simplicity: Single-mass flywheels lack the complexity of dual-mass flywheels, making them inherently more reliable. Dual-mass flywheels contain a rubber damper or hub that will, like all rubber components, wear out with time.
Pedal Feel: Many enthusiasts prefer to eliminate BMW's "Self Adjusting Clutch", which has been known to provide an unpredictable, inconsistent engagement point.
Driveability: Valeo's conversion kit has been designed to maintain nearly identical clutch and flywheel weight, ideal for keeping the clutch quiet and easy to drive.
Kit contents:
Single-mass flywheel
Non-Self Adjusting Clutch and pressure plate
Throw out bearing
Pressure plate bolts
Flywheel bolts
Clutch alignment tool
BMW E60 E9X XACT Flywheel Streetlite is an advanced performance flywheel engineered to offer substantial improvements over stock components. This lightweight flywheel is designed for durability and enhanced performance, making it an excellent choice for both street driving and drag racing.
Upgrade your BMW with the BMW E60 E9X XACT Flywheel Streetlite for enhanced performance and durability.
Advanced Clutch Technology (ACT) designs, engineers and develops products by leveraging decades of track and performance street experience. Advanced CAD, FEA simulation, and CAM tools help ensure highly optimized performance, reliability, and repeatability. These key advantages are produced by combining the best engineering and design methodologies with the latest in materials and manufacturing techniques.
ACT clutch kits stand unequaled in terms of consistent pedal feel, high torque capacity, long wear life and durability. In-house manufacturing is critical in tuning components specifically to each individual application while maintaining the predictable ACT pedal feel across the entire catalog.
This clutch kit features an Xtreme pressure plate and an R6 racing clutch disc.
Their Xtreme pressure plate offers a 50-120% clamp load increase, moderate to heavy pedal feel, and is recommended for high performance street and racing applications. All diaphragms went through a four stage heating process for increased strength and unparalleled performance.
Next in this kit is the R6 racing clutch disc. This disc is an unsprung, rigid disc with 6 pads that is best suited for drag and road racing and handles heat better thanks to its increased surface contact area versus the 4 pad version of this disc, the R4. The R6 pads are composed of ceramic friction materials and the disc has a chome-moly hub that is heat treated for additional strength under high load engagements. Over stock, this disc is much better for faster shifting and significantly higher torque loads. Unlike the stock disc, this racing disk has a slightly shortened life span due to its rigid design and pad composition. This in turn is offset thanks to its fast, aggressive engagement for track use.
Clutch Kit Specs: