BMW Intake Parts for BMW 3 Series E92 (2007-2013)

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

The VTT PCV Flapper delete is used to get rid of the factory flapper, and add a -10 fitting on N54 powered vehicles. This will allow you to run a single or dual external catch can, or your own custom set up.

This fitting is made from 6061-T6 aircraft aluminum anodized black and comes with O-ring, and a stainless steel holding clip.

This part fits the following BMW engines:
2006-2012 N54

Turbosmart GenV Raceport BOV (Fits competitors 50mm / female style flange. No weld flange included)

The Race Port is renowned for its exceptional compactness and lightweight design tailored for turbocharged competition-level engines. With its innovative collar design and internal flow structures, this BOV stands out as 50% lighter and 25% smaller than competing models, yet it boasts an impressive flow rate of 330 CFM, making it the market's top-performing BOV in its category.

Fits Chargepipes With Tial/Turbosmart Flange

In addition to the weak stock chargepipe, the factory N54 diverter valves can also be a source for boost leaks. The diverter valve takes overboost and re-directs it back through the intake and turbos instead of allowing it to pass into the intake manifold. It's the same as a blow off valve (BOV) but instead of releasing into the engine bay, it stays contained to the engine. The stock diverter valves (DV) are plastic and connect with more plastic into the chargepipe and turbo inlet pipes. The plastic can become brittle and crack even on stock engines and leak boost, which leads to a loss in power and performance.

Turbosmart has developed two kits to replace and upgrade the stock diverter valves - a direct replacement kit and a combination DV/BOV "Dual Port" kit (shown). This Dual Port Kit is a DV and a BOV together in one unit. An internal valve directs some of the charged air into the turbo inlets and the rest is dumped into the engine bay like a traditional BOV. The amount of boost released into the air is determined by an internal spring in the Dual Port unit (additional springs are also available). This allows you to custom tailor how much boost and BOV "whoosh" you hear. In addition to the DV/BOV combo, stronger silicone hose is included to connect them to the turbo inlet pipes (Vargas silicone inlets are recommended). The Turbosmart Kompact Dual Port will give you all of the strength and reliability you need to take your turbo build to the next level.

You will also need T#553932 

In addition to the weak stock chargepipe, the factory N54 diverter valves can also be a source for boost leaks. The diverter valve takes overboost and re-directs it back through the intake and turbos instead of allowing it to pass into the intake manifold. It's the same as a blow off valve (BOV) but instead of releasing into the engine bay, it stays contained to the engine. The stock diverter valves (DV) are plastic and connect with more plastic into the chargepipe and turbo inlet pipes. The plastic can become brittle and crack even on stock engines and leak boost, which leads to a loss in power and performance.

Turbosmart has developed two kits to replace and upgrade the stock diverter valves - a direct replacement kit (shown) and a combination DV/BOV "Dual Port" kit. This direct replacement kit includes new high-performance DV and stronger silicone hose to connect them to the turbo inlet pipes (Vargas silicone inlets are recommended). The Turbosmart Kompact DV will give you all of the strength and reliability you need to take your turbo build to the next level.

You will also need T#553932 

• Seamless plug-and-play installation
• Minimizes leakage for enhanced turbocharger performance
• Retains OE control for optimal operation
• Superior thermal performance to maximize boost without stressing the turbocharger

VTT is proud to offer the very best Cold Side charge pipe solution for the BMW E Series N54 platform. This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipe rated at over 200 psi.  They are molded for the perfect fit in your engine bay, while not sacrificing anything in the way of flow or size. They also completely isolate your charge air from any additional heat soak coming in from the engine or ambient heat.  Another huge benefit is only TWO connections which are barbed and has many small ridges which dig into the silicone so it’s impossible for the pipe to blow off.

This N54 pipe has a flange installed to support a Turbosmart BOV.

This is the EASIEST N54 charge pipe on the market to install hands down. Install takes about half an hour even if you are inexperienced with working on your own car, can take as little as 15-20 minutes if you have had it apart a few times.

The kit includes:

VTT Cold Side Silicone Charge pipe

2 VTT Branded CNC adapters to mount the map sensor, and a methanol bung

1 VTT Branded CNC adapters for the TB inlet

2 VTT branded T-Bolt Clamps

1 1/8 NPT port is included in the charge pipe for methanol