BMW Tools & Specialty Equipment for BMW 3 Series E93 (2007-2013)

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

Schwaben offers the right tools to make your next project a success. Everything from complex engine scanners to brake bleeders and spring compressors, Schwaben tools has you covered.

Some of the recommended use include but are not limited to:

• Remove and install rear ball joints on E38, E39, E60/61, E63/64, E65/66, and E70's
• Removal and installation of ball joints and bushings on rear control arms on E36, E46, E39, E60/61, E63/64,  E65/66, E70, E83 and E85/86 Z4's
• Removal and installation of rear sub frame mounted differential bushings on E36, E46, E83 and E85/86 Z4's
• Removal and installation of rear differential mounted bushings on E36, E46, E9X, E60/61, E63/64, E65/66, and E85/86 Z4's

Plastic five-piece tool kit removes trim and door panels, moldings, and adhesive backed logos and badges, without damage. By using a non-marring plastic you can safely and easily remove trip pieces with confidence

?

Features:

• Pull-type remover

• Narrow edge remover

• Wide edge remover

• Handle remover

• Upholstery clip remover

Our 3/8-inch drive, 36mm, 6-point socket grips tight and won’t slip. Low profile oil filter housing removal socket fits in tight places. 

• BMW M52 and M54
• MINI Gen 1 (R50, R52, and R53)

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

The perfect kit containing most of your needed European essentials. 

Features:

• 13PCS-1/4" DR.6PT SOCKETS: 4, 4.5 , 5 ,5.5 ,6 , 7, 8 ,9 ,10, 11, 12, 13, 14MM 
• 1PC- 1/4" DR. QUICK RELEASE RATCHET (72T).
• 2PC- 1/4" DR.50 & 100MM EXTENSIONS 
• 1PC- 1/4" DR.150MM FLEXIBLE EXTENSION
• 1PC- 1/4" DR.UNIVERSAL JOINT
• 1PC- 1/4" DR.SLIDING T-BAR
• 1PC- 1/4" DR.6" SPINNER HANDLE
• 1PC- 1/4" DR.1/4" BIT HOLDER ADAPTER
• 4PCS-HEX KEY WRENCHES:1.27, 1.5,2,2.5MM
• 6PCS-1/4" HEX SOCKETS:3,4,5,6,7,8MM
• 3PCS-1/4' SLOTTED SOCKETS:4,5.5,7MM
• 3PCS-1/4" PHILIPS SOCKETS:PH1, PH2, PH3
• 3PCS-1/4"POZI SOCKETS: PZ1, PZ2, PZ3
• 6PCS-1/4" TORX SOCKETS: T10, T15, T20, T25, T30, T40

Own an E30? This tool kit is a perfect fit for your glovebox!

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

Safety is always the most important factor when it comes to working under your car, jack stands are highly recommended. 

Features:

• Ultra light  jack stands only weigh 4.7 lbs each
• All aluminum construction with heavy-duty  flanged bases to safely stabilize loads
• 6 locking positions for a secure load in multiple heights
• Extra heavy duty load pin at .584 in. diameter with a posi lock ball to insure it stays in place
• Min. Height is 10.6
• Max Height is 15.4"
• Large 7" diameter base
• Outer support tube is 2-1/8" in diameter

Tired of busting your knuckles from old hardened exhaust hangers?

This Schwaben tool removes the hanger by pressing on the steel hanger bracket and pulling the rubber hanger in one motion. Self centering force pin locks onto the pin while the flat paddle pulls off the rubber hanger from behind. Slim profile and a 25 degree offset works in tight areas.

Ensure precise clutch installation with this specialized alignment tool, designed specifically for N54-equipped BMWs. While most aftermarket clutch kits include a generic alignment tool, many are intended for the N55, which is incompatible with the N54 due to differences in pilot bearing mounting and flywheel design.

This tool is engineered for both 6-bolt (01/2009+) and 8-bolt (-01/2009) N54 flywheels, allowing you to accurately center and align the clutch disc on the flywheel during pressure plate installation. Achieve a hassle-free and precise fit with this essential service tool.

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
• Deluxe transverse support for even more stability
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

These weld protectors allow you to safely jack up your vehicle without crushing or bending any pinch welds. These will fit any jack and will work with many jack stands such as the Schwaben Aluminum Jack Stands.

Specifications:

• 3" wide
• 1" tall
• Single groove top
• Double grooved bottom

The fuel pump is held into the tank with a retaining lock ring. Most people would take an extension or punch and tap out the ring with a hammer. But that's the wrong way to do it. You could damage the lock ring, or worse, the tank itself. This handy tool is toothed to match the lock ring and takes a standard 1/2 drive ratchet or small extension. Twist the ratchet and the lock ring comes un-done cleanly and smoothly. A hefty tool that pays for itself over and over. Fits most BMWs from 1988-2013. Also has application for MINI and Porsche.

This metal screw ring tightens down to old the top of the fuel pump or fuel filter assembly dependent on model of vehicle.

Together they make this job simple and easy and ensure a tight fit with a new ring.