BMW Tools & Specialty Equipment for BMW 3 Series E93 (2007-2013)

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible 3/8"-inch drive click-to-stop
• Torque range of 5 to 80 ft-lb
• Accurate to within +/-4%

The perfect kit containing most of your needed European essentials. 

Features:

• 13PCS-1/4" DR.6PT SOCKETS: 4, 4.5 , 5 ,5.5 ,6 , 7, 8 ,9 ,10, 11, 12, 13, 14MM 
• 1PC- 1/4" DR. QUICK RELEASE RATCHET (72T).
• 2PC- 1/4" DR.50 & 100MM EXTENSIONS 
• 1PC- 1/4" DR.150MM FLEXIBLE EXTENSION
• 1PC- 1/4" DR.UNIVERSAL JOINT
• 1PC- 1/4" DR.SLIDING T-BAR
• 1PC- 1/4" DR.6" SPINNER HANDLE
• 1PC- 1/4" DR.1/4" BIT HOLDER ADAPTER
• 4PCS-HEX KEY WRENCHES:1.27, 1.5,2,2.5MM
• 6PCS-1/4" HEX SOCKETS:3,4,5,6,7,8MM
• 3PCS-1/4' SLOTTED SOCKETS:4,5.5,7MM
• 3PCS-1/4" PHILIPS SOCKETS:PH1, PH2, PH3
• 3PCS-1/4"POZI SOCKETS: PZ1, PZ2, PZ3
• 6PCS-1/4" TORX SOCKETS: T10, T15, T20, T25, T30, T40

Own an E30? This tool kit is a perfect fit for your glovebox!

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

Safety is always the most important factor when it comes to working under your car, jack stands are highly recommended. 

Features:

• Ultra light  jack stands only weigh 4.7 lbs each
• All aluminum construction with heavy-duty  flanged bases to safely stabilize loads
• 6 locking positions for a secure load in multiple heights
• Extra heavy duty load pin at .584 in. diameter with a posi lock ball to insure it stays in place
• Min. Height is 10.6
• Max Height is 15.4"
• Large 7" diameter base
• Outer support tube is 2-1/8" in diameter

Tired of busting your knuckles from old hardened exhaust hangers?

This Schwaben tool removes the hanger by pressing on the steel hanger bracket and pulling the rubber hanger in one motion. Self centering force pin locks onto the pin while the flat paddle pulls off the rubber hanger from behind. Slim profile and a 25 degree offset works in tight areas.

Ensure precise clutch installation with this specialized alignment tool, designed specifically for N54-equipped BMWs. While most aftermarket clutch kits include a generic alignment tool, many are intended for the N55, which is incompatible with the N54 due to differences in pilot bearing mounting and flywheel design.

This tool is engineered for both 6-bolt (01/2009+) and 8-bolt (-01/2009) N54 flywheels, allowing you to accurately center and align the clutch disc on the flywheel during pressure plate installation. Achieve a hassle-free and precise fit with this essential service tool.

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
• Deluxe transverse support for even more stability
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

Featuring a T60 Torx head, the belt tensioner found on the N54/N55 engine has exceptionally tight quarters. Use of this tool will allow access to the lock pin hole without excessive component removal, making belt removal and installation a much easier task.

This tool fits all N54/N55 powered BMW, including: 
2008+ E82 BMW 135i 1M Coupe 
2014+ F22 BMW M235i 
2006+ E90 BMW 335i 335xi 335i xDrive - Sedan 
2007+ E92 BMW 335i 335is 335xi 335i xDrive - Coupe 
2007+ E93 BMW 335i - Convertible 
2012+ F30 BMW 335i 335i xDrive - Sedan 
2013+ F32 BMW 435i 435i xDrive - Coupe 
2014+ F34 BMW 335i xDrive GT - Gran Tourismo 
2015+ F80 BMW M3 - Sedan 
2015+ F82 BMW M4 - Coupe 
2015+ F83 BMW M4 - Convertible 
2006-2010 E60 BMW 535i 535xi 535i xDrive 
2010+ F07 BMW 535i GT, 535i xDrive GT 
2011+ F10 BMW 535i 535i xDrive 
2012+ F13 BMW 640i 
2009+ F01 BMW 740i 740li 
2011+ F25 BMW X3 xDrive35i 
2007-2013 E70 BMW X5 xDrive35i 
2007-2014 E71 BMW X6 xDrive35i 
2009+ Z4 BMW Z4 sDrive35i Z4 sDrive35is 

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point long reach deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.