BMW Intake Parts for BMW 4 Series F32 (2014+)

Bring your aFe filter back to life with a Restore kit from aFe. Included is filter cleaner & replacement oil. These air filter oils is designed to not harm MAF sensors, while allowing the filter to catch as much debris as possible.

Used for Pro 5 R filters

Engines make more power when you're able to move as much air and fuel as possible through them. However, air density is just as important as air volume. Cooler air is denser air, so in addition to keeping your engine cool, it's important to make sure that your intake charge is as cool as possible. Turner Motorsport's upgraded intercooler works to reduce air temperatures with a bare minimum of pressure drop. Less pressure drop means less restriction, and a turbocharger that doesn't have to work as hard. This results not only in a longer service life for your turbocharger, but a substantial increase in performance as well.

The stepped design increases volume and surface are in a limited space by adding an additional smaller core at the top of the intercooler. Both cross sectional area and frontal surface area are increased by a whopping 56%, with a design that still weighs under 20 pounds. On the stock intercooler, the temperature differential between the inlet and outlet sides of the intercooler represented a 95 degree drop. With the Turner Motorsport intercooler, that drop was increased to a chilling 140 degrees. The dyno results don't lie: as a bolt-in upgrade, expect gains of 18 wheel horsepower and 10 lb/ft of torque. With a tune and supporting modifications, further gains are possible, up to 36 horsepower and 28 lb/ft of torque.

This cast aluminum intercooler features an attractive, easy to clean matte black finish, with etched Turner logos on the front and bottom. If you're looking for the ultimate cooling system upgrade for your turbo BMW, look no further.

• Cast aluminum construction
• Bar and plate design
• 56% increase in frontal surface area & cross sectional area
• Decrease in temperature of 45 degrees from inlet side to outlet side (95 degree drop stock on outlet side vs. 140 degree drop on Turner outlet side)
• Significantly less restriction (pressure drop of consistently 0.75 psi vs. 1.5-2.5 psi stock)
• +18HP/10TQ (+36HP/28TQ with tune and supporting mods)
• Weighs under 20 lbs.
• Overall size: 520mm wide, 210mm tall
• Mounting hardware inlcuded

Upgrade to the following OE Intercoolers: 17517600531, 17517600530, 17517618809

Fits the Following BMWs:

F22 F23 228i 228i M235i M235ix

F30 F31 F32 F33 F34 F36 328i 328ix 335i 335ix 428i 428ix 435i 435ix

The Dynamic Air Scoop (D.A.S.) from aFe Power is a very simple, bolt-on product that increases air flow and velocity through the factory kidney bean grille. This lightweight rotomold intake scoop is black for a stealth appearance. You will notice the improved throttle response as the speed of your intake air flow is increased.

This scoop is a perfect addition to an aFe Stage 2 Sealed intake system part number 54-82202 and 51-82202. All necessary hardware is included.

This is a drop-in stock replacement aFe performance air filter that installs into your BMW's factory airbox. This version has an oil-free filter media for less maintenance. For the best flowing filter, with the best performance gain, we always recommend the standard aFe "Pro5R " filter (which has a blue pre-oiled filter media), but this oil-free filter flows only slightly less than the blue Pro5R style aFe filter, and requires no re-oiling after cleaning the filter.

Fits in vehicles with the following engines: B46 2.0L, B58 3.0L

7" Tall "Oil Free" Air Filter:
This intake system utilizes an oil free, 7" tall conical 360 degree radial flow performance air filter with 3-layers of synthetic media providing maximum airflow and performance.

High Quality Tube:
This system uses a high quality, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit.

Lightweight Vacuum Form Plastic Cover w/ Auxiliary Air Inlet:
Creates a stealthy under-hood look while reducing air intake noise without sacrificing power. A urethane plug is also included if you wish to block off the auxiliary air inlet.

Hassle-Free Installation:
All clamps, coupling and hardware are included for hassle-free installation. This is a direct bolt-on kit that requires no cutting or drilling on factory parts.

DETAILS:

• 350 CFM Rating
• +12 HP / +12 lbs. x ft. Torque max gains
• Outflows factory intake
• CAD-Designed Roto-Molded Intake Tube
• Vacuum Form Cover for Stealthy Under-Hood Look
• Pro DRY S oil-free 3-Layer Synthetic Media for Maximum Convenience With Excellent Filtration Efficiency
• No Cutting or Drilling on Factory Parts for Faster Installation

Note 1:
Does NOT fit Convertible models.

Note 2:
This product is not currently CARB exempt and is not available for sale in California or for use on any vehicle registered with the California Department of Motor Vehicle.

BMW Cold Air Intake System delivers more cool air to your BMW's engine, enhancing performance and producing an aggressive yet refined turbo whistle. Designed for significant performance improvements and ease of use, this intake system offers a range of benefits.

• Dyno-Proven Gains: Increases power by up to +7 HP and torque by +14 Lbs. x Ft.
• Improved Airflow: Outflows the factory intake by 34% for better engine breathing.
• High-Performance Flow: Measures 605 CFM @ 7" H2O for efficient air delivery.
• Open-Element Design: Allows visibility of the large air filter while sealing when the hood is closed to prevent hot air ingress.
• Convenient Filter: Features a washable and reusable Pro DRY S air filter for easy maintenance.
• Easy Installation: Innovative filter-to-housing interface and minimal hardware ensure a quick and straightforward setup.

7" Tall Air Filter:
This intake system utilizes an oil free, 7" tall conical 360 degree radial flow performance air filter with 5-layers of progressive finer mesh cotton media providing maximum airflow and performance.

High Quality Tube:
This system uses a high quality, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit.

Carbon Fiber Look Cover w/ Auxiliary Air Inlet:
This carbon fiber look cover is constructed with lightweight vacuumed formed ABS plastic for underhood appearance. A urethane plug is also included if you wish to block off the auxiliary air inlet.

Hassle-Free Installation:
All clamps, coupling and hardware are included for hassle-free installation. This is a direct bolt-on kit that requires no cutting or drilling on factory parts.

Note 1:
Does NOT fit Convertible models.

Note 2:
This product is not currently CARB exempt and is not available for sale in California or for use on any vehicle registered with the California Department of Motor Vehicle.

This all new Momentum sealed intake system produced up to 11hp and 15lbs. x ft. torque and outflows the factory intake by 37%. The air filter is housed in a one-piece, patent pending black rotomolded housing that keeps warm engine air out for maximum performance. This unique, one piece, housing with a built in clear sight window allows you to inspect the filter without disassembly. A C.A.D. designed intake tube was engineered to unleash all avaliable horsepower and to fit perfectly. The kit comes complete will all necessary hardware.

Sealed Housing w/ Sight Window: A unique, one piece, sealed housing with a built in clear sight window allows you to inspect the filter with no disassembly.

Housing/Air Filter Interface: This intake system features a unique patent pending filter to housing interface which allows for an easy installation and maximizes filter size.

Horizontal Louvers: The louvers were added to the roto-molded housing to increase the cold air to the air filter.

7-1/2" Tall Conical Pro 5R Air Filter: This intake utilizes a huge, 7-1/2" tall conical PRO 5R performance air filter for increased performance. The PRO 5R air filter uses five layers of progressively finer mesh cotton gauze media to provide maximum airflow for best performance results. Washable and reusable for multiple cleaning cycles, the tall, open, evenly spaced pleats provide excellent dust holding capacity for a longer service cycle between cleanings.

7" Tall Air Filter:
This intake system utilizes an oil-free, 7" tall conical 360-degree radial flow performance air filter with 5-layers of progressive finer mesh cotton media providing maximum airflow and performance.

High-Quality Tube:
This system uses a high quality, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit.

Black Cover w/ Auxiliary Air Inlet:
This carbon fiber look cover is constructed with lightweight vacuumed formed ABS plastic for underhood appearance. A urethane plug is also included if you wish to block off the auxiliary air inlet.

Hassle-Free Installation:
All clamps, coupling and hardware are included for hassle-free installation. This is a direct bolt-on kit that requires no cutting or drilling on factory parts.

Note 1:
Does NOT fit Convertible models.

Note 2:
This product is not currently CARB exempt and is not available for sale in California or for use on any vehicle registered with the California Department of Motor Vehicle.

This Stage 2 cold air intake system produces 11 max horsepower, 15 lbs. x ft. torque and out-flowed the factory intake by 38%. This system includes a durable powder-coated heat shield and features a washable/reusable conical Pro 5R air filter for maximum flow. This air filter is constructed with 100% polyurethane, for long life and multiple cleaning cycles. A huge one-piece mandrel bent wrinkle-black powder-coated intake tube, maximizes air velocity providing maximum performance and throttle response. This is a direct bolt-on kit and requires no cutting or drilling.

Perfect Fit:
Includes stainless steel clamps for a leak-free seal and heavy-duty 5-Ply reinforced silicone coupling for strength.

Mandrel-bent Tubing:
Constructed of 2-1/2" to 2-3/4" mandrel-bent aluminum tubing and powder-coated textured-black for heat and corrosion resistance. The smooth transition mandrel bends decrease turbulence which increases horsepower and torque. The high-temp wrinkle-black powder-coating insulates the tube from engine heat and protects the tube from corrosion.

aFe Badging:
Unique aluminum laser-cut aFe Power logo plate is welded-on for an aggressive style.

Also Fits:
2014-2016 BMW 128i/ix (F20/21) L4-2.0L (t) N20
2014-2016 BMW 228i/ix/220i (F22/23) 14-16 L4-2.0L (t) N20
2013-2016 BMW 320i/ix (F30/31/34) L4-2.0L (turbo) N20
2012-2016 BMW 328ix (F30) L4-2.0L (turbo) N20
2013-2016 BMW 328i/ix (F31/34) L4-2.0L (turbo) N20
2014-2016 BMW 420i/ix (F32/33) L4-2.0L (turbo) N20
2014-2016 BMW 428i/ix (F32/33/36) L4-2.0L (turbo) N20

Note: This intercooler tube is not CARB exempt at this time and is not legal for sale in California or use on vehicles registered with the California Department of Motor Vehicle.