Packaged by Turner for BMW 4 Series F32 (2014+)

When replacing your worn out brakes, the market is flooded with performance options. If your BMW doesn't see track time, it's not very practical. Performance pads and rotors tend to result in a lack of bite at low braking temperatures and cause excessive noise in daily driven vehicles that becomes irritating. BMW brakes from the factory are perfectly suited for trips around town, across the country, and even the occasional spirited driving session, delivering smooth, quiet, and long lasting performance. 

Included in this F3X BMW brake package are all of the OEM equivalent components needed to replace your Front & Rear brakes with comfort, reliability, and optimal lifespan in mind.

Brake components in this kit:

• Pagid Front & Rear Brake Pads
• Zimmerman Front & Rear Rotors
• New Front & Rear Wear Sensors
• Brand New Stainless Steel Set Screws
• Syl-Glide Silicone Brake Lubricant 

Fits the following BMWs:
F3X BMW 335 340 435 440 (w/ M Sport Brakes)

Maintaining proper oil levels in your engine is crucial for peak performance. Undetected leaks can cause your oil to drop to dangerously low levels between oil changes, leading to severe engine damage.

One common culprit for oil leaks is the valve cover. Over time, exposure to extreme temperature fluctuations can wear down the gaskets, causing them to fail. Prevent oil leaks and protect your engine by replacing these vital components.

Comprehensive Kit Includes:

Valve Cover Perimeter Gasket Valve Cover Inner Gasket ​Valvetronic Motor Gasket Replace your old gaskets with our high-quality kit to keep your engine running smoothly and efficiently.

Replacing your struts and shocks? Don't forget the bushings! The rubber mounts for the shocks will go bad over time, especially if you drive hard or the roads are particularly rough. The shock mounts locate the front struts and rear shocks to the car - providing a quiet and vibration-free buffer between the road and the cabin. Shock mounts and bushings can wear out just like any other rubber part on the car. This leads to more noise and harshness reaching the chassis and may complicate your new suspension install. When installing new shocks, that is the perfect time to also replace the mounts. There is no additional time to install them, no special tools required, and doesn't take any extra time! If you re-use the original mounts you have the risk of them failing before your next shock replacement, doubling your labor costs.

Fits the following BMWs:
2014-03/2015 F22 BMW 228i 228iX M235i M235iX - vehicles without EDC
2012-03/2015 F30 BMW 320i 320iX 328i 328iX 335i 335iX - Sedan - vehicles without EDC
2014-03/2015 F34 BMW 328i 328iX 335iX - Gran Turismo - vehicles without EDC
2014-03/2015 F32 BMW 428i 428iX 435i 435iX - Coupe - vehicles without EDC
2014-03/2015 F33 BMW 428i 428iX 435i 435iX - Convertible - vehicles without EDC
2014-03/2015 F36 BMW 428iX 435iX - Gran Coupe - vehicles without EDC

The water pumps in these BMW models are known for failure near 80,000 miles is a very common issue often times leaving the owner stranded. This kit provides a single stop for water pump and thermostat replacement needs to save the search and get you back on the road.

Kit includes:

• Genuine BMW Thermostat
• OEM Pierburg Electric Water Pump
• Genuine BMW Antifreeze/Coolant
• OEM Mounting hardware required for both the thermostat and water pump

If your engine has higher mileage, don't neglect rod bearing replacement! These bearings are sandwiched between the connecting rod and crankshaft journal and are prone to failure due to overheating, lack of lubrication, or general wear. Replace your rod bearings and prevent a spun bearing.

Starting with ACL’s high-performance bearing shells, our Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Kit includes:

Turner Motorsport WPC-Treated Race Series Rod Bearing Shells (8) Genuine BMW Connecting Rod Bolts (8) Assembly Lube (4 oz.)