BMW Tools & Specialty Equipment for BMW E10 2002tii M15 2.0L

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible 3/8"-inch drive click-to-stop
• Torque range of 5 to 80 ft-lb
• Accurate to within +/-4%

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

Tired of busting your knuckles from old hardened exhaust hangers?

This Schwaben tool removes the hanger by pressing on the steel hanger bracket and pulling the rubber hanger in one motion. Self centering force pin locks onto the pin while the flat paddle pulls off the rubber hanger from behind. Slim profile and a 25 degree offset works in tight areas.

Safety is always the most important factor when it comes to working under your car, jack stands are highly recommended. 

Features:

• Ultra light  jack stands only weigh 4.7 lbs each
• All aluminum construction with heavy-duty  flanged bases to safely stabilize loads
• 6 locking positions for a secure load in multiple heights
• Extra heavy duty load pin at .584 in. diameter with a posi lock ball to insure it stays in place
• Min. Height is 10.6
• Max Height is 15.4"
• Large 7" diameter base
• Outer support tube is 2-1/8" in diameter

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

These weld protectors allow you to safely jack up your vehicle without crushing or bending any pinch welds. These will fit any jack and will work with many jack stands such as the Schwaben Aluminum Jack Stands.

Specifications:

• 3" wide
• 1" tall
• Single groove top
• Double grooved bottom

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point long reach deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

Custom exhaust work in the plans? The Schwaben Exhaust Pipe Cutter will help you cut out old pipe or cut down new pipe with ease. It can cut any pipes from 3/4" to 3" in diameter and cuts pipe with only 1/4 turn adjustments, thanks to 15 blades that effectively cut the entire pipe with little movement. This is great for tight to reach places that prevents you from using more traditional non-specialty tools.

Features:

• Cuts from 3/4" pipe up to 3" pipe
• 15 cutting blades
• Rubber covered handles for grip and comfort

This hand held Schwaben tool makes changing fluids an easy, quick task.The Schwaben fluid suction/fill pump suitable for oils, water and any non corrosive liquid.

Features 

• Comes with a flexible and a rigid tube. 
• Flow rate is adjustable for different functions.
• 350 ML capacity
• Cylinder is marked in 20 mL increments and fraction of quarts for accurate filling. 

Not for use with gasoline.

The Schwaben Dual Temperature Heat Gun Kit is the ideal tool for stripping paint, removing decals, shrinking wire wrap, etc. The heat gun has a switch which allows for two different heat settings (572F and 932F).

Features:

Four airflow adapters, 1pc Large Deflector Nozzle, 1pc Reduction Nozzle, 1pc Small Deflector Nozzle, and 1pc Reflector Nozzle.
Voltage 120C, 60 HZ
Amps 12.5A
Two heat settings: Low Heat up to 572 Degree F. High Heat 932 Degree F.
Air Volume: Low Heat: 10 cfm (280L/min) High Heat: 17 cfm (480 L/min)
Wattage: Low Heat: 1000W High Heat: 1500W
Has 6.75 Ft cord.
Built in hook to hang on wall.
For California Prop 65 warning see: www.P65Warnings.ca.gov. and photo below.

All the right bits in one box. The perfect assortment to keep the job going.

Features:

• 10 fractional SAE hex, 9 Torx® tamper-proof, 9 Torx®

• 9 Metric hex bits, 9 slotted bits, 8 Pozi-drive, 8 Phillips, 4 square-recess, 4 tri-wing

• 3 spline, 3 Torq, 3 clutch, wing-nut driver, magnetic bit holder and socket bit holder

• Made of hardened Chrome Vanadium steel for years of dependable use

• Packaged in a handy blow molded case with individually marked bit slots for easy organization

A professional quality flex ratchet features a fine satin finish designed for durability and easy clean up.

Features:

• Special designed 72T gear mechanism
• 5 degree of handle movement between gears 
• Flex head has 7 detent positions in a 180 degree swing
• Push button release holds socket tight until you are ready to release
• Ratchet is a full 290mm ( 11") long for extra leverage.

Limited Lifetime Warranty

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.