BMW Tools & Specialty Equipment for BMW E10 2002tii M15 2.0L

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

Our aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

Better still, order two: one for your garage and another for the emergency tool kit in you trunk.

The Foxwell T20 TPMS sensor integrates both 315 MHz and 433 MHz frequencies, replacing more than 99% of OEM direct TPMS sensors on the market. The all-new, high-precision air valve prevents air leakage and provides a durable seal - an upgrade over the outgoing T10. Its proprietary sensor body features a long-lasting, lightweight 3V battery and supports unlimited wireless programming. Sensors can easily be activated and programmed with the Foxwell T2000 TPMS Service Tool (T#36811799).

Features:

Rubber valve stem Supports 315MHz and 433MHz frequencies High-precision air valve to avoid air leakage 0-30° adjustability Built-in battery with an extended service life (more than 5 years) Temperature reading range of -40°F to 257°F Pressure monitoring range of 0 to 130.53 psi 12G weight

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

These weld protectors allow you to safely jack up your vehicle without crushing or bending any pinch welds. These will fit any jack and will work with many jack stands such as the Schwaben Aluminum Jack Stands.

Specifications:

• 3" wide
• 1" tall
• Single groove top
• Double grooved bottom

Schwaben Oil Filter Removal Pliers / Wrench are designed to tackle the most stubborn spin-on filters with ease. Featuring large, adjustable jaws with raised teeth, these pliers provide a secure grip on a wide range of filter diameters. The long, plastic-coated handles offer a comfortable grip and added leverage, making filter removal straightforward and efficient.

• Efficient Removal: Handles the toughest oil filters with ease, thanks to its robust design.
• Versatile Fit: Adjustable jaws with raised teeth ensure a secure grip on various filter sizes.
• Comfortable Use: Long, plastic-coated handles provide a comfortable grip and extra leverage.
• Durable Construction: Built to last, ensuring reliable performance for frequent use.

Warning: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. For more information, visit Proposition 65.

The Schwaben Dual Temperature Heat Gun Kit is the ideal tool for stripping paint, removing decals, shrinking wire wrap, etc. The heat gun has a switch which allows for two different heat settings (572F and 932F).

Features:

Four airflow adapters, 1pc Large Deflector Nozzle, 1pc Reduction Nozzle, 1pc Small Deflector Nozzle, and 1pc Reflector Nozzle.
Voltage 120C, 60 HZ
Amps 12.5A
Two heat settings: Low Heat up to 572 Degree F. High Heat 932 Degree F.
Air Volume: Low Heat: 10 cfm (280L/min) High Heat: 17 cfm (480 L/min)
Wattage: Low Heat: 1000W High Heat: 1500W
Has 6.75 Ft cord.
Built in hook to hang on wall.
For California Prop 65 warning see: www.P65Warnings.ca.gov. and photo below.

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Take one wrench, not two to your next fluid service. The Schwaben Service Wrench fits both crankcase and drain plugs in BMW, Mercedes, and other European vehicles.

Features:

• Six-point 17mm box end won’t round off engine oil drain plugs
• Hardened 14mm hex at the opposite end fits many transmission fill and drain plugs
• Made of vanadium steel with polished chrome finish
• Long handle for added leverage.

Fits most vehicles with M10, M20, M30, M42, M44, M50, M52, M54, M56, M70, S14, S38, S50, S52 and S70.

Application note: Please verify the exact size of the transmission and differential plugs in your car. BMW has used both 14 and 17mm plugs in some vehicles. 

The Schwaben Metric Bubble Flaring Tool Set stands as the ultimate solution for achieving precise brake line connections and flawless tubing applications. This tool set unlocks the ability to craft immaculate ISO bubble flares on brake lines and tubing systems commonly found in European, Japanese, and select domestic model brake lines. The outcome? Connections that are not only secure but also capable of thriving under your vehicle's demanding conditions.

At its core, this set features a robust and enduring hardened steel bar, embodying the essence of durability. Complementing this bar is an extensive array of adapters tailored for 4.75mm, 6mm, 8mm, and 10mm tubing, showcasing the set's versatility across various applications.

Discover unparalleled precision as you secure your brake lines and tubing with the utmost accuracy. This tool set empowers you to effortlessly shape bubble flares, guaranteeing connections that are both leak-proof and resilient. Whether you're a devoted automotive technician or a passionate enthusiast, the Schwaben Metric Bubble Flaring Tool Set is right for you!

Includes:

• Schwaben Metric Bubble Flaring Tool
• Hardened Steel Bar for Enduring Durability
• Adapters for 4.75mm, 6mm, 8mm, and 10mm Tubing

Schwaben 8-Pc ATF Adapter Set is designed to provide a versatile solution for working with automatic transmission fluid (ATF) systems. This comprehensive adapter set includes multiple sizes to ensure compatibility with a wide range of vehicles, making it an essential tool for automotive professionals and DIY enthusiasts alike.

• Versatile Compatibility: Includes multiple adapters to fit various vehicle makes and models, making it a valuable addition to any automotive toolkit.
• High-Quality Construction: Made from durable materials to withstand the rigors of professional use and provide reliable performance.
• Enhanced Precision: Ensures accurate fluid transfer and servicing by providing the correct adapter size for different ATF systems.
• Convenient Set: Contains all necessary adapters for a comprehensive solution, eliminating the need for separate purchases.
• Easy to Use: Designed for straightforward application, allowing for efficient and effective ATF service and maintenance.