Please ensure your correct model is selected
These adjustable rear links are only required when using sway bar / swaybars with a suspension with a very low ride height, where it may be necessary to adjust the length of the end links for proper sway bar clearance from the drive axles or other suspension components. These suspensions are usually found only on race cars but this may also apply to street cars with sport springs/sport coil overs that are lowered a lot. On most street cars lowered 1.5" or less, the stock links will be fine.
These end links feature a Heim joint, which allows enough lateral movement when disconnected to adjust the length of the link without removing the entire link from the car. This is particularly helpful when eliminating or adjusting preload while tuning the suspension. Similar links without this joint, can't be adjusted without totally removing the link from the car.
Built-in grease fittings allow for occasional lube, and a packet of grease is included. These links are sold as a set, and include two end links and hardware for H&R and TMS sway bars (other brands may not need the hardware).
At their shortest setting they are 2.875" hole to hole and on their longest setting they are 3.5" hole to hole.
*Note: these links will not work with factory or non-adjustable Eibach sway bars.
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
Stock rear lower control arms offer very little adjustment for alignment, especially in lowered vehicles, due to their use of an eccentric bolt. These aftermarket performance control arms from ECS Tuning are designed for maximum adjustability, allowing you to maximize handling and minimize tire wear.
To ensure maximum reliability, ECS Tuning's control arms are constructed from strong, lightweight 6061-T6 aluminum and feature a 303 stainless steel center turnbuckle that offers over 8 degrees of fast and precise camber adjustment. The inner bushing is a stock style serviceable OEM bushing for long life and inexpensive maintenance.
Features:
Durable construction suitable for the daily driver and track car alike
8+ degrees adjustment range for dialing in any suspension and wheel/tire setup
Center located adjuster for maximum clearance during adjustment
OEM-style bushing for long life and inexpensive service
Black anodized 6061-T6 aluminum with 303 stainless steel turnbuckle
Includes new hardware
*With the exception of the stance community, most enthusiasts will need no more than a few degrees of adjustment range. Total adjustment often is dependent on wheel/tire clearances.
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
TMS rear subframe bearings are designed to limit rear control arm movement relative to the subframe. The stock BMW subframe bushings are made out of rubber, which allows variance in suspension position due to deformation and compression. A race car needs to have all suspension points remain in place for proper setup. By using high grade aircraft aluminum alloy and high performance race bearings, the TMS bushing replacements are both lightweight and strong. The casing is designed so that if maximum motion occurs, the load will be evenly distributed throughout the casing. Our flanges are designed to spread the load on the subframe and limit movement. The bearing we use is an extra wide race bearing to distribute the load over a broader area. Each piece is anodized or nickel plated to withstand corrosion. These bushings are a perfect compliment to the TMS lower camber arms.
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
A very common weak point on the 3 series BMW is the sheetmetal of the rear shock tower. The sheetmetal here is relatively thin and very susceptible to stress and fatigue. A worn out shock will bottom-out more often and this energy is transferred through the bump stop and into the metal chassis. Stiffer shocks and shock mounts also put more stress on the sheetmetal. Factor in age, mileage, and environmental conditions and it's not a surprise that we see shock tower failures often. BMW addressed this issue with reinforcements of their own but our's are thicker for additional strength. This kit mounts on top of the shock tower and can either be bolted or welded in place. Because of the shape of the rear shock tower, these do not fit cabrio/convertible cars.
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
Worn rubber differential mounts will lead to the differential twisting and shifting around in the rear subframe. Not only will this be noisy but it's bad for driver confidence and bad for the chassis as well. Even on fresh rubber bushings the differential has deflection and twist, especially if the car has been modified for more torque. Since the differential is centrally mounted in the rear subframe, with all suspension mounts interconnected, a differential with too much deflection will affect handling and could even damage the rear subframe.
These 88A urethane E46 M3 diff mounts are much stiffer than stock but still not as solid as our Turner aluminum/Delrin bushings. This set will resist twisting much better than the stock rubber mounts. Included is the front diff mount and two rear mounts in the cover.
If you are looking for a wider range of camber adjustability in the rear of you car, the IRP Adjustable rear lower control arm is exactly what you need! Built to be much stronger than stock, these rear control arms feature inner monoball bushings and are built of steel, reducing the weight as well. These are perfect for a lowered car or for a track car that needs a greater level of rear adjustment.
Features:
This item fits the following BMWs:
1992-1999 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2006 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
The rear subframe is the heart of the BMW rear suspension. Not only do all of the suspension arms attach to it, the driveline runs through it via the differential and half-shafts. Therefore, a track-prepped E46 should never see any flex or deflection in any of the subframe mounts. Excessive movement here transfers to unwanted suspension motions elsewhere and is also a major contributor to failures in the rear floor sheetmetal.
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
The E36/E46 rear trailing arm bushings (RTABs) wear out faster than any other bushing on the car. Worn RTAB will cause excessive toe alignment change and give a 'loose' or 'floaty' feeling in the rear handling. One of the reasons for this is that they over-extend during motion, stretching and twisting the rubber in all directions. These shims sit on either side of the bushing and limit the amount of extension from the bushing. Not only will you get more life from your RTAB but these will help stiffen the bushing during cornering. But during normal driving you will still have all of the comfort of the stock rubber bushings. These part about these bushings is how easy they are to install - simply slide them in place during your bushing install. They can be added to pre-installed bushings too by dropping the trailing arm and removing the cage around the bushing.
Works with stock rubber bushings only (not urethane or Delrin).
Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.
By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components.
Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
These camber plates are perfect for the enthusiast owner who wants a high quality design with a motorsports background. Knowing a full race kit on the street is not often the best option, we took the best features from the Race Camber Plates and incorporated them into a fresh Street design -
The Turner E46 M3 Street Camber Plates are the most advanced design on the market. These are designed specifically for the E46 M3 - no shortcuts or cookie-cutter components. We started with a fresh design to make these very user friendly and easy to install and set up. The E46 M3 front suspension has unique geometry and the strut is mounted at an angle that can put significant side loading on the strut shaft if it's not located properly. The location and angles for the main bearing were carefully engineered to allow the proper motion ratio and strut angles during adjustment. This greatly reduces bending forces on the strut itself which improves performance and longevity. By designing for one chassis we're able to focus on what works best in that application - proper fitment and operation without unnecessary adapters, easy-to-use camber and caster adjustments, and an intelligent modular design.
For street use we added a pliable urethane bushing to absorb vibration and a special base design that works with the factory radial bearing and spring perch. The radial bearing allows the spring to rotate instead of twisting and binding. By re-using the factory radial bearing we can keep the assembled stack height lower for maximized shock travel. It's also a commonly-available item that you can get from any BMW dealer at a low price. All of the things that make it work well in the factory application carry over to our design. You can use our camber plates with a stock sized spring, 60mm, or 2.5" springs. Use your stock spring perch/bearing with stock-sized springs. The 60mm and 2.5" upper spring perches are sold separately. The beauty of our design is that you can use the factory radial bearing with any of these springs.
Another important feature of the Turner Camber Plates is the size of the upper plate. Our plates have a very large surface area to better spread strut forces through the strut tower. A smaller upper plate, like those found on competitor's kits, will localize strut forces and contribute to strut tower deformation ('strut tower mushrooming'). This is a very important feature especially as these cars get older and spend more time on the track. Deformed strut towers are a serious performance and safety concern and our camber plates are properly designed to handle the loads. The factory strut reinforcement plates are not required with our camber plates (but you can use them if you want to).
Since this design is specific to the E46 M3, we can build it with the bare minimum of adapters and extra hardware. This not only cuts down on confusion but makes it easier to assemble and operate. We use the correct-sized bearing for the 16mm strut shaft; no sleeves or bearing adapters required. The original tapered lower mount support and a small stainless steel spacer from our kit are all that's required to install. We have used our camber plates with most of the major strut manufacturers on the market - stock Sachs/Boge, Bilstein, Koni, H&R, ST, and KW. Our camber plates work with any strut that is designed to accept the factory strut mount.
Click here for installation instructions.
This item fits the following BMWs:
2001-2006 E46 BMW M3
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
Our renowned TMS adjustable front sway bar / swaybar links for BMWs are now available in custom lengths, making them easy to order for any aftermarket or custom suspension setups. Simply measure for your ideal link length, and order the links with the best length range (below). Each sway bar link has a 10mm diameter mounting pin/stud, which is the typical factory/stock size for a universal fitment. These are sold by the pair, and each set includes two matching sway bar end links.
These end links offer the quiet operation and long life of "stock" BMW end links, but with the strength and adjustability of rod-end style sway bar links. These sway bar links can be used on a wide variety of BMWs and aftermarket BMW suspensions. When measuring, please consider that the length ranges of our Custom Adjustable end links are measured from the center to center on the end link mounting stud / pin, as shown in our diagram.
Note for E9X M3: the unique mounting on the M3 strut requires a set of our adapter seats (#TSU9912AF9). You can add them with your links from the menu below.
TMS Part#Center to Center (mm)Center to Center (inch)
TSU9912A35155.00mm - 170.00mm6.10" - 6.69"
TSU9912A40170.00mm - 185.00mm6.69" - 7.28"
TSU9912A45180.00mm - 195.00mm7.08" - 7.67"
TSU9912A50190.00mm - 205.00mm7.48" - 8.07"
TSU9912A55207.00mm - 222.00mm8.15" - 8.74"
TSU9912AF1220.00mm - 235.00mm8.66" - 9.25"
TSU9912A70240.00mm - 255.00mm9.45" - 10.04"
TSU4612AF3250.00mm - 265.00mm9.84" - 10.43"
TSU9912A80261.00mm - 276.00mm10.28" - 10.87"
TSU5012AF8280.00mm - 295.00mm11.02" - 11.61"
TSU9912A95290.00mm - 305.00mm11.42" - 12.00"
TSU9912110320.00mm - 335.00mm12.59" - 13.19"
TSU9912115330.00mm - 345.00mm12.99" - 13.58"
TSU9912130362.00mm - 377.00mm14.25" - 14.84"
TSU9912135370.00mm - 385.00mm14.57" - 15.16"
TSU9912140381.00mm - 396.00mm15.00" - 15.60"
TSU9912145389.00mm - 404.00mm15.31" - 15.91"
Please select your length below.
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
Rear Axle Carrier Panel (RACP) failure is a well-documented issue that plagues all BMW E46 models. Due to thin sheet metal mounting, the forces applied during cornering, acceleration, and braking create stress fractures in the carrier panel, resulting in large cracks or breaks that risk the structural integrity of your chassis. To fix this issue, many enthusiasts opt to install weld-in reinforcement plates on the underside of the RACP. While this remedies the formation of additional stress cracks and adds rigidity to failure-prone areas, it does not prevent the entire carrier panel from flexing during high-performance driving.
Our all-new Rear Subframe Reinforcement Brace is engineered to add structure to the E46's rear chassis under high-stress conditions, eliminating the common weak points in the RACP while providing the confidence you need for performance driving. Don't let chassis flex limit your car’s potential—upgrade your E46 with the Turner Motorsport Rear Subframe Reinforcement Brace today!
How It Works:
During performance driving, the Rear Axle Carrier Panel (RACP) must react the forces of longitudinal and lateral accelerations. During forward acceleration, the differential transmits torque through the subframe to the RACP, forcing the rearmost subframe mounting points downward. This downward movement flexes the carrier panel, reducing its ability to handle torque efficiently. By linking the rearmost subframe mounting points to the rear shock towers, downward flex is restricted, resulting in improved torque transfer and stability. Alternatively, high-grip cornering generates lateral acceleration (side-to-side) forces across the RACP. Similar to how a rear strut brace functions, connecting the rear shock towers helps to counteract these forces. Adding the subframe to this connection further reduces lateral loads, eliminating side-to-side flex and enhancing overall stability.
Features & Design:
Four-Point Triangulated Structure: Links the rearmost subframe mounting locations to both rear strut towers for superior load distribution. Enhanced Stability: Reduces lateral and longitudinal RACP flex during acceleration, braking, and cornering. Improved Torque Transfer: Minimizes downward flex of the RACP, ensuring efficient power delivery for enhanced driveability. High-Performance Durability: Heavy-duty steel tube construction ensures lasting support during spirited driving, track use, and for vehicles with increased power output. Blue Powdercoat Finish: Offers fantastic corrosion resistance, protection from scuffs and scratches, and a stylish appearance that is sure to complement your performance-centric E46. Underside Reinforcement Compatibility: Designed to work seamlessly alongside our underside RACP reinforcement plates (TDR4675412, T#91). Kit Includes:
Rear Subframe Brace Sedan Subframe Brace Spacers Extended-Length Drill Bit (1/4", 12" Overall Length) High-Speed Drill Bit (12.5mm, 152mm Overall Length) Drill Bit Guide Extended Subframe Bolts Zinc-Plated Steel Hex Nut (2) Installation & Support:
Need installation tips? Our team has assembled a guided start-to-finish installation tutorial, including detailed instructions on drilling and cutting your trunk floor panel for perfect fitment. Click HERE for Installation Instructions
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
Rear trailing arm bushings serve the key purpose of keeping rear suspension triangulated and the vehicle moving where it's directed to. Though failure prone, even factory-fresh OEM rubber bushings allow for deflection, causing suspension geometry changes on hard launches, over bumps in the road, and during cornering. This deflection results in clunking in the rear end, a “rear steer” feeling, and uneven tire wear.
Powerflex polyurethane rear trailing arm bushings are firmer than OEM bushings, resulting in a reduction of deflection that causes these suspension angle changes, improving handling over bumps and with a proper alignment, extending tire wear.
Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
This Product fits the following BMWs:
E36 1992-1999 318i 318is 318ti 320i 323i 325i 325is 328i 328is
E46 2000-2006
Z4 All
Looking to stiffen up your rear shock mount without going for a solid rear mount? The Polyurethane Rear Performance Strut Mount from IRP will give you the stiffer reinforcement without giving you the typical noise, vibration, and harshness that come with traditional performance strut mounts. The polyurethane also helps with preventing rear shock blowouts, a common problem for stock BMW rear mounts that are paired with stiffer than stock suspension.
The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.
Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels
Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.
Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every
BMW E36 E46 KW Replacement Front End Link - Each is crafted to enhance the suspension performance of BMW E36 and E46 models, ensuring precision and stability on both road and track. Built with high-quality materials to meet KW’s exacting standards, this replacement front end link is designed to provide consistent handling and improved durability, especially when paired with KW coilovers or other suspension upgrades.
Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.
Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
This part fits the following BMWs:
All 1999-2006 E46
All 2002-2008 E85 Z4
Subframe bushings play a vital role in securing the subframe to the chassis, and factory rubber bushings often compromise between comfort and handling. Powerflex polyurethane subframe bushings, firmer than OEM counterparts, significantly improve handling, provide a more stable rear-end, and enhance suspension articulation while maintaining a comfortable ride. As Europe's top-selling suspension bushing manufacturer, Powerflex utilizes cutting-edge techniques to create premium performance bushings, ensuring longer durability compared to OEM rubber bushings and elevating overall driving experience.
Tasked with keeping the vehicles rear end firmly mounted while absorbing noise, vibration, and harshness (NVH) factory rubber subframe bushings were engineered to provide a balance of control while keeping the ride quality soft and supple. As a factory bushings age, they become brittle and begin to harden. When this happens the bushing will actually shrink and allow excess play, or movement in the subframe. This is typically felt by a sudden jerk or "thunking" noise under acceleration and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushings with full polyurethane this play is eliminated since the subframe is being held in place by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering and acceleration inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.
Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
For BMW E36 and E46 chassis this tubular style arm is great when lowering this popular vehicle, or for correcting rear camber on stock vehicles.
Rear Adjustment range: Camber -1.00° to +3.00°
Installation time: 1.3 hr/side
Required: 1 per wheel
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
Our experience with spherical front control arm ball joints go back to those we designed and used in our IMSA E90 328i and E92 M3 racecars (GS class Champions in 2011). We wanted to offer e30, e36, and e46 owners similar levels of handling precision and control for the track and street, but weren’t satisfied with the other options out there. Instead of a Delrin bushing or unsealed spherical bearing alone, we selected an oversized sealed greaseable spherical monoball to offer unparalleled durability and precision, but designed a Delrin adapter sleeve to help isolate the added noise, vibration, and harshness that a full solid monoball bearing will have. While race-ready, our hybrid Delrin/monoball control arm bearings are more at home on the street than other kits that are advertised as “race-only” bearings. We did extensive street, autocross, and track testing to ensure the spherical bearing used in this bushing design excelled in each setting.
The stock rubber bushings, even those found in the M3, allow significant fore/aft movement of the front wheels to help absorb road impacts, especially when being pushed hard. This soft flexible design maximizes daily driving comfort, but also allows considerable alignment change. This unwanted deflection stands between you and a crisp, confidence-inspiring driving experience. The advantage of a monoball bearing is that it will not deflect under load, eliminating all unwanted deflection while still allowing complete freedom of movement in the desired angles. What you get is superior steering precision with better handling from more consistent alignment and direct braking feedback, with exceptional service life. Thanks to the Delrin insert and double lip seals, there's none of the extra noise or reduced service life often found on other spherical bearings.
In short, if you're seeking front control arm bushings that offer precise, predictable handling, crisper braking feel, with a long service life free from noise - look no further. We have you covered.
Watch to learn more about Turner Monoball Bushings
Features:
Bearing housing
Bearing
Includes new hardware. Grease before installation and with each oil service with high quality Moly grease for maximum service life. Need a grease fitting tool?
Installation is relatively easy - see our instructions here.
This item fits the following BMWs:
2001-2006 E46 BMW M3
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
Sway bars transmit cornering forces from the outside wheels to the inside wheels, helping to keep the vehicle flat during cornering. This in turn reduces body roll and improves the driver's cornering confidence. OEM rubber sway bar bushings are designed with comfort in mind, allowing the sway bar to articulate while permitting additional movement, leading to less-than-ideal bar retention and causes unnecessary body roll.
Powerflex polyurethane sway bar bushings are firmer than factory rubber bushings, reducing body roll and keeping sway bars in check. Polyurethane bushings won't slop around like OEM bushings, allowing sway bars to function at their fullest potential.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
NOTE: For use with factory 21.5mm sway bar only
Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.
By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components.
Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
This part fits the following BMWs:
2001 - 2006 E46 M3
Optimize rear suspension geometry with Whiteline suspension bushings. Often overlooked, Whiteline trailing arm bushings offer superior dynamic alignment precision by controlling excessive movement - providing driver reassurance for more predictable handling.
Features:
Upgrade your E46's rear subframe with the Revshift Combo Kit, featuring 80A durometer polyurethane rear subframe bushings and a comprehensive weld-in reinforcement plate kit. Designed to address the notorious cracking and ripping of rear subframe mounting points over time, this kit provides a robust solution to prevent costly damage to your vehicle.
Key Features:
Complete Solution: Includes 95A durometer polyurethane rear subframe bushings and precision laser-cut 14-gauge steel reinforcement plates for comprehensive subframe reinforcement. Prevents Damage: Weld-in reinforcement plates protect against cracks and damage to the chassis, ensuring long-term durability and stability. Enhanced Handling: Revshift polyurethane rear subframe bushings replace OEM rubber bushings, stiffening mounting points to improve handling and performance. Durable Construction: Polyurethane bushings are designed to last and do not wear out like rubber OEM bushings, providing consistent performance over time. Proper Dampening: Polyurethane bushings properly dampen the rear subframe, enhancing overall vehicle stability and control. Benefits:
Improved handling capabilities Long-lasting durability compared to OEM rubber bushings Protection against bending or cracking of subframe mounts The comprehensive kit includes all necessary components for installation Upgrade your E46's rear subframe with the Revshift Combo Kit for superior handling, durability, and protection against chassis damage. Boost your driving experience with enhanced performance and stability.
Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.
The Pro Kit uses an Eibach Pro Kit spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach springs tend to be softer overall than most other aftermarket springs, which ensures the ride stays close to a stock comfort while still giving you a lowered stance and improved handling.
Bilstein B12 Features:
Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.
This item fits the following BMWs:
2001-2006 E46 BMW M3
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
Sway bars transmit cornering forces from the outside wheels to the inside wheels, helping to keep the vehicle flat during cornering. This in turn reduces body roll and improves the driver's cornering confidence. OEM rubber sway bar bushings are designed with comfort in mind, allowing the sway bar to articulate while permitting additional movement, leading to less-than-ideal bar retention and causes unnecessary body roll.
Powerflex polyurethane sway bar bushings are firmer than factory rubber bushings, reducing body roll and keeping sway bars in check. Polyurethane bushings won't slop around like OEM bushings, allowing sway bars to function at their fullest potential.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
NOTE: For coupe models only
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
The rear springs on the 2001-2006 E46 M3 models have a chronic broken spring problem. If it hasn't happened to you yet it will. Springs are nothing more than exposed steel and they rust easily. After a while a section of the spring actually breaks off.
A broken spring is very dangerous - the spring is no longer mounted correctly in the suspension and it cannot support the weight of the car, especially when cornering. The ride also suffers as the suspension is no longer able to absorb the bumps and impacts from the road. Aside from a visual inspection of the spring itself you might notice a clunking sound or banging noise coming from the front or rear. An inspection of the noise should also include other related items in the suspension: bushings, ball joints, links, mounts, etc. We also recommend replacing the rubber spring pads on the top and bottom of the spring because they lose their shape over time.
The factory BMW springs sell for $140+ each. We sold and replaced enough while working in New England that we were able to get a strong grasp of the issue and come up with our own springs that are an improvement over the factory springs in every way. These springs are made in Germany using high grade spring steel that is then shot-peened for longer life and powder-coated for protection. These are the same height as the stock replacement BMW springs which makes them a direct replacement.
Replaces Coupe models only.
This item fits the following BMWs:
2001-2006 E46 BMW M3 Coupe
Upgrade your E46's rear subframe with the Revshift Combo Kit, featuring 80A durometer polyurethane rear subframe bushings and a comprehensive weld-in reinforcement plate kit. Designed to address the notorious cracking and ripping of rear subframe mounting points over time, this kit provides a robust solution to prevent costly damage to your vehicle.
Key Features:
Complete Solution: Includes 80A durometer polyurethane rear subframe bushings and precision laser-cut 14-gauge steel reinforcement plates for comprehensive subframe reinforcement. Prevents Damage: Weld-in reinforcement plates protect against cracks and damage to the chassis, ensuring long-term durability and stability. Enhanced Handling: Revshift polyurethane rear subframe bushings replace OEM rubber bushings, stiffening mounting points to improve handling and performance. Durable Construction: Polyurethane bushings are designed to last and do not wear out like rubber OEM bushings, providing consistent performance over time. Proper Dampening: Polyurethane bushings properly dampen the rear subframe, enhancing overall vehicle stability and control. Benefits:
Improved handling capabilities Long-lasting durability compared to OEM rubber bushings Protection against bending or cracking of subframe mounts The comprehensive kit includes all necessary components for installation Upgrade your E46's rear subframe with the Revshift Combo Kit for superior handling, durability, and protection against chassis damage. Boost your driving experience with enhanced performance and stability.
Sway bars transmit cornering forces from the outside wheels to the inside wheels, helping to keep the vehicle flat during cornering. This in turn reduces body roll and improves the driver's cornering confidence. OEM rubber sway bar bushings are designed with comfort in mind, allowing the sway bar to articulate while permitting additional movement, leading to less-than-ideal bar retention and causes unnecessary body roll.
Powerflex polyurethane sway bar bushings are firmer than factory rubber bushings, reducing body roll and keeping sway bars in check. Polyurethane bushings won't slop around like OEM bushings, allowing sway bars to function at their fullest potential.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
Click here for installation instructions.
