Sometimes choosing the correct shift kit proves difficult when you dual-purpose your favorite vehicle, we understand this well. The early days for any race enthusiast usually begins with a car that is needed to daily drive and setup to get out on the track. What becomes difficult is properly modifying that car to feel comfortable in both situations which is why we took this view on our new short shift line. This upgraded lever is a quick swap option to replace the standard shift lever that come with our kits so you can keep your hands closer to the wheel while shifting at high speeds. Designed from anodized aluminum this lever looks great in any interior for the daily driver who simply prefers the taller lever look and feel.

NOTE THAT THESE ARE DESIGNED TO WORK WITH TURNER MOTORSPORT SHORT SHIFTERS ONLY - We wanted to give you the option to buy one separately, in case you changed your mind after buying our short shifter.

Features:

Compatible with stock shift boot fits nicely into the machined groove at the bottom of the lever to maintain a clean look in the interior.
Machined from 6061-T6 aluminum and type II anodized for exceptional durability and corrosion resistance.
Available in either black or clear anodize to match your vehicle’s interior.
Rally shift knob is machined from black delrin.
Unlike aluminum, delrin will not hold heat so on those hot days you won’t have to worry about burning your hand on a knob that’s been baking in the sun.
Shift knob is threaded onto the end of the shift lever utilizing a standard ⅜-16 thread to allow for easy removal and attachment of your favorite beer tap or other accessory.
“Quick Change” height adjustable upper shift lever design allows for quick swapping between optional “OE” style and “Rally Style” upper shift levers.
22mm adjustment range to fine tune shifter throw and feel.

If allowed in the rules these solid aluminum transmission mounts offer many advantages over a urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. These are machined from solid aluminum and have zero deflection, engine torque will cause a rubber or urethane mount to flex or deflect allowing more torque to passed through the drive line (instead of being wasted winding up the mount). This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of transmission mounts you will ever need. We very strongly recommend using the solid transmission and engine mounts together as a complete kit, mixing a rubber mount with a metal mount will cause undue stress on the mounting points and will lead to a failure. We never advise using a solid mount unless a corresponding solid mount is also used.

These are a no-compromise design for all-out racing use, full solid aluminum mounts should not be used on street-driven cars since there is no material to absorb vibration making these quite harsh for regular street use (track cars don't care about noise).

Product features and benefits:

• Crisper throttle response, positive shifter location, direct power transfer
• Precision machined billet 6061-T6 aluminum housing
• Grade 10.9 stud - fear not, big turbo owners
• Engineered in-house and made in America

This item fits the following BMWs: 
1989-1995  E34 BMW  525i 530i 535i 540i M5 
1992-1998  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 
1997-2003  E39 BMW  525i 528i 530i 540i M5 
1999-2005  E46 BMW  323i 323ci 325i 325ci 328i 328ci 330i 330ci M3 
2008-2012  E82 BMW  128i 135i 1M Coupe 
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan 
2006-2012  E91 BMW  328i - Wagon 
2007-2013  E92 BMW  328i 335i 335is - Coupe 
2007-2013  E93 BMW  328i 335i - Convertible 
1997-2002  Z3 BMW  Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe ​

Single piece 6061 construction, optimized cooling, provisions for temp sensor and external cooler!

Built to last, made from a single piece of 6061 billet aluminum with a rugged and good-looking hard-coat anodizing our diff cover can handle anything you throw at it. Not only is it an absolute masterpiece to look at but this billet diff cover checks all the boxes for features needed. Reinforced mounting ears for strength and stability, never again will you break an ear off your diff cover like the factory units are known to do. Each ear is unified with the one-piece billet cover and features added material for the highest durability possible. This diff cover is cool, literally, the entire construction was designed with optimized cooling in mind. Internal fins are strategically placed serving as effective heat sinks for optimal heat dissipation. This ensures stable temperatures, promoting longevity for both the fluid and your differential. Additionally, the internal design ensures continuous oiling and lubrication of the ring gear, maintaining its stability and preventing fatigue by controlling heat more effectively. An internal baffle at the cover's corner helps maintain proper pressure and prevents cavitation.

All of the OEM features were retained along with the upgrades. The mounting surface was designed to be compatible with both the OEM gasket or RTV of your choosing, some people don't trust the gaskets and we get it. Factory bushing geometry allows you to use any E46 diff busing including rubber, poly, and even solid mounts. The drain and fill plugs on the diff cover are upgraded to -6AN using the provided high-pressure fittings with replaceable o-rings. The drain and fill plugs can now also be used for expanding to an external oil cooler allowing you to further expand the fluid capacity for optimized cooling and service intervals. To keep an eye on things from the driver seat is 1/8 NPT provision for temp sensors, this product from Turner has you covered at every turn.

Why the upgrade?

Upgrading to our Billet Differential cover gives you the strength you need to push your car to its limits. In addition to its enhanced strength, this differential cover includes numerous other upgrades and conveniences. These include increased capacity, improved cooling and lubrication for the ring gear, upgraded fill and drain plugs, and the option to expand an external oil cooler for extreme motorsport usage. Designed to complement both upgraded daily drivers and extensively modified track cars, all while looking good in the process.

Key Benefits:

Reinforced mounting ears for strength and stability - never again will you break an ear off during an aggressive drive or track event
Increased capacity
Sight glass for checking fluid level without removing fill/drain plug
External fins on the casing for maximum cooling and consistent fluid temps
Internal cooling fins for even more temperature control
Optimized internal design to keep fluid consistently on the ring gear
Integrated breather to prevent cavitation by venting the appropriate amount of pressure being built up in the diff housing
-6AN ports to incorporate the use of a differential cooler - this increases capacity and lowers temps allowing for extended fluid change intervals
1/8 NPT fitting for the use of a temp sensor to monitor fluid temperature
Design:

Fits large case 210/215mm differentials
Single piece 6061 Billet aluminum construction
T6 Black hard coat anodizing for superior corrosion resistance and aesthetics
Compatible with most differential coolers(-6AN) and temp sensors(1/8 NPT)
Designed to accommodate oversized rear sway bars
Retains OEM mounting features including the use of the OEM gasket
Factory geometry bushing size for use with OEM and aftermarket poly bushings
Easy access to sensors and drain/fill plug
Retains OEM speed sensor and wire mount location
Product development:

Our Reinforced Billet Diff Cover was designed, engineered, tested, and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

Used when retrofitting an OEM or aftermarket CSL intake on a vehicle with SMG transmission.

Its no secret the CSL intake plenum is the pivotal upgrade for your S54. If you are fortunate enough to have an SMG equipped vehicle you are going to need a bracket to relocate the expansion tank. Our Turner motorsport bracket fits perfectly with the engine bay to facilitate the installation of your genuine or Turner branded CSL intake plenum.

Design:

Direct fit, perfect OEM replacement
304SS sheet metal design, engineered to be simpler and cheaper than its formed OE counterpart
Reverse engineered with FARO laser scanning and Solidworks CAD technology

ECS Tuning's Polyurethane Transmission Mounts are designed to address the vital role of transmission mounts in your vehicle's suspension. The factory mounts are notorious for failures that can result in over-revving, mis-shifts, and in extreme cases, potential chassis damage. Our polyurethane mounts provide a robust solution, engineered for both street and track applications, guaranteeing enhanced performance while eliminating concerns about torn mounts.

Polyurethane stands out with its exceptional toughness, durability, and impressive wear resistance compared to rubber. It also exhibits resistance to water, oil, and grease while retaining its original shape even when subjected to significant compression. By reducing deflection, polyurethane facilitates effective power transfer. While there may be a slight increase in NVH (Noise, Vibration, Harshness), the benefits far outweigh this minor compromise in ride comfort. With a polyurethane durometer of 70A, our street mounts are versatile, offering both daily driving comfort and track durability. For more track-oriented enthusiasts, we provide stiffer mounts with an 80A durometer rating.

For a hassle-free installation, we supply a comprehensive DIY guide. ECS Tuning ensures that you are fully supported from start to finish.

Enhance your car's performance with ECS Tuning's polyurethane transmission mounts, designed for both street and track applications. These mounts are engineered to withstand high torque and forced-induction scenarios, eliminating concerns about torn mounts and providing a more engaging driving experience. Although polyurethane may introduce some additional NVH (Noise, Vibration, Harshness), its exceptional durability, wear resistance, and resistance to water, oil, and grease make it the perfect choice for performance enthusiasts. ECS Tuning offers two durometer options to match your driving style, along with a comprehensive DIY installation guide, ensuring a complete solution for your transmission mount requirements.

Key Features:

• Minimized transmission movement, reducing the risk of mis-shifts and over-revs.
• Made from high-quality polyurethane bonded with 304 Stainless Steel.
• Enhanced driving experience for both street and track enthusiasts.
• Two durometer options available: 80A for race applications and 70A for daily driving (ES#2859359).
• Replaces weak OEM mounts.

Some modifications to your vehicle may not produce power to create gains in the overall performance of your driving. When you add a "Po' Boy" clutch stop to your BMW the performance gain is directly felt in the driving experience.

The ECS clutch stop allows the driver to fine tune the position of the clutch pedal to closely match the engagement point for precise, quicker shifting. The adjustment range found in this product can be set to the stock engagement point or can be adjusted to follow the wear of the clutch.  Meaning your new experience will never change all the way to the end of the clutch life and can be reset to enjoy the next clutch.

Note: This modification might require some slight modification to the clutch switch mounting bracket, which can be bent slightly by hand.

Enhance Your BMW's Performance with the BMW Teflon Shifter Bushing Kit

• Improves shifting precision and responsiveness
• Reduces play and slop in the shifter mechanism
• Made from high-quality Teflon material for durability
• Easy to install with no modifications required

Upgrade your BMW's shifting performance with the BMW Teflon Shifter Bushing Kit. This kit improves shifting precision and responsiveness by reducing play and slop in the shifter mechanism. Crafted from high-quality Teflon material, the bushings offer durability and long-lasting performance. Installation is straightforward, requiring no modifications to your vehicle.

Requires shorter flywheel bolts - 8x (P# 11227805885) - T#12322

Lightweight flywheels have proven themselves to be a worthwhile performance enhancement. But with the quicker throttle response and horsepower improvement comes one serious drawback: flywheel chatter. Without the dual-mass flywheel's rubber isolators, a lightweight aluminum flywheel has more rattle than stock. ECS has designed this flywheel using chrom-moly steel and it weighs almost ten pounds less than the stock DMF but not as extreme as full aluminum flywheels. The steel helps dampen vibration and noise so you get near-factory refinement and most of the benefits of a lightweight flywheel: quicker throttle response, better reliability, and more power to the wheels. This flywheel requires the E34 M5 sprung hub clutch kit.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

Stock flywheel weight - 25.0lbs
ECS flywheel weight = 16.55lbs

This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed)

Ensure the longevity of your BMW's drivetrain with ECS Tuning's Magnetic Plugs. These plugs are meticulously engineered in-house to provide a perfect fit and feature a permanent magnet attached to the plug body. The magnet effectively attracts and captures tiny abrasive and ferrous metal particles, preventing their circulation through lubrication systems. Metal particles can accumulate due to various conditions such as normal wear, machining operations, casting flaws, and stress usage, leading to excessive wear of vital components. ECS Tuning's Magnetic Plugs help alleviate this concern by trapping these particles, thus safeguarding the internal components of your drivetrain. With a convenient 17mm hex head design, these plugs eliminate the need for special tools required for OEM plugs.

Key Benefits:

• Removes abrasive metal particles from drivetrain fluid
• Prevents excessive wear to internal components
• Meticulously engineered for a perfect fit
• Features a permanent magnet for efficient particle capture
• Convenient 17mm hex head design for easy installation

BMW E46 Z4 Rear Polyurethane Differential Bushing Performance is the ultimate upgrade for enhancing the connection between your BMW's chassis and differential. Designed by Turner Motorsport, this performance bushing replaces the soft factory rubber with durable polyurethane, offering superior control and response. By minimizing vibrations and reducing deflection, this bushing ensures a more direct and responsive driving experience, making it a must-have for any performance-oriented BMW E46 or Z4 owner.

• Enhanced Performance: Replaces the soft factory rubber with durable polyurethane for improved driveline response.
• Reduced Vibrations: Minimizes vibrations between the chassis and differential, providing a more connected driving experience.
• Increased Durability: Made from high-quality polyurethane, offering long-lasting performance under demanding conditions.
• Improved Control: Reduces deflection, ensuring a more precise and responsive handling experience.

Looking to eliminate your dual-mass flywheel? Overwhelmed with all the options, but hearing complaints about so many of them with rattling or chatter from them? Problem solved. Introducing the all-new Lightweight Performance Flywheel from ECS Tuning. Engineered in-house with the enthusiast daily driver in mind, this is the perfect option for those wanting a lightweight flywheel without the annoying chatter heard from so many other options on the market. Designed to accommodate all conditions: from Sunday drives through the country, to the abuse of the track. No matter your driving style or ability, this is the flywheel and clutch kit for you.

Key Features:

Eliminates factory dual-mass flywheel for:
Crisper shifts
Improved throttle response
Improved acceleration (We measured a .4s decrease in 0-60 times on an otherwise-stock E36 328i!)
Lower replacement cost
Hardened 4140 Chromoly Steel for excellent engagement feel and wear resistance; zinc plated for corrosion resistance
Designed for use with any E34 M5 pressure plate and clutch for OE-type clutch feel
Sprung-hub clutch disc to eliminate chatter at idle and reduce driveline shock loading
Weighs in at just 16.5lbs!
SFI tested and certified to ensure safe operation under all conditions
Includes ECS performance flywheel, clutch kit with throwout bearing, pilot bearing and all flywheel and pressure plate hardware
Why is SFI testing and certification important?

The SFI Foundation, Inc. (SFI) is a non-profit organization established to issue and administer standards for the quality assurance of specialty performance and racing equipment. SFI certification indicates a flywheel has been certified using industry-standard SFI Spec 1.1 standards by an independent testing body to ensure quality of both design and materials for flywheels utilized in competitive motorsports.

Having successfully passed SFI certification, this flywheel has an individual SFI serial number found in a laser etching, and on an affixed sticker. This certification means the ECS-engineered flywheel is safe and reliable during the rigors of competitive racing; it's also safe and reliable for years and years of street use.

Pair with T#363031 or any flywheel designed to be used with the E34 M5 clutch.

Upgraded clutch kit to be used with E34 M5 architecture flywheels. Designed for factory and upgraded street car applications to handle up to 375 Ft/lbs at the crank.

Whether you're replacing a worn-out clutch or upgrading for increased power handling, this E34 M5 clutch kit offers a reliable solution for enhanced pedal feel, power capacity, and overall driving satisfaction.

Paired with a modified geometry flywheel, the E34 M5 style clutch is ideally suited for most E36, E46, and others using the same powertrain. It checks all the boxes for essential clutch replacement features. While some aftermarket options may address slipping issues and worn-out clutches, they often sacrifice pedal feel, providing little to no resistance. A soft clutch not only kills the driving experience of your BMW but also reduces confidence when pushing the car to its limits.

On the contrary, you might be in the market for an upgraded clutch to handle your modified engine/forced induction builds. You go from an OE or aftermarket clutch option that has a lackluster and soft pedal feel to the complete opposite side of the spectrum, a very stiff clutch that grabs like an on-and-off switch making the clutch a pain almost undrivable on the street resulting in your favorite car turning into your least favorite car to drive.

The E34 M5 clutch kit balances performance with practicality, ensuring a satisfying driving experience whether you're maintaining your BMW or preparing it for increased power demands.

Kit Contents:

Performance Clutch Disc and Pressure plate
Throw-out Bearing
Clutch Alignment Tool
Pilot Bearing
Clutch features:

Torque Capacity (Crankshaft):
375 Ft / Lbs
Clutch Disc:
240mm Full face, performance organic friction material with integrated copper for enhanced heat dissipation and a long component life
OE-like friction backing plate design for smooth engagement with dual-stage damping springs to reduce gear noise and driveline chatter, and for smooth engagement
Pressure Plate:
Increased clamp force over OEM, rated at 1,729lbs of pressure
Throw-out Bearing:
OE spec for ease of installation and reliable operation
Clutch Alignment Tool:
BMW small 10 spline design, made for perfect fitment into the crank bore
Perfect clutch disc spline and size, easy removal with pull tab
​Not all aftermarket clutch kits include this proper alignment tool! We ensured you received the proper tool for trouble-free installation!
Fitment:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed)
1977-1989 E24 BMW M6
1982-1988 E28 BMW M5
1987-1995 E34 BMW M5

Enhance the shifting experience of your BMW E46 M3 with the BMW E46 M3 Teflon Shifter Bushing Kit. This high-quality bushing kit is designed to reduce play and improve precision in the shifter mechanism, resulting in smoother and more accurate shifts. Engineered specifically for BMW E46 M3 models, this kit offers easy installation and durable performance. Upgrade your BMW's shifting performance with this premium Teflon shifter bushing kit.

• Reduces play in the shifter mechanism
• Improves shifting precision for smoother and more accurate shifts
• Engineered specifically for BMW E46 M3 models
• Easy installation for convenient upgrade

From the factory, the E46 M3 featured a dual-mass flywheel and self-adjusting clutch kit. While this provided an easy, comfortable driving experience, it lacks the durability and performance features of an upgraded clutch and flywheel kit. ECS Tuning's all-new S54 performance clutch kit is designed to address these issues. Featuring a full-face clutch disc and heavy-duty pressure plate, this kit offers increased power-holding capability, exceptional pedal feel, and superior durability.

The factory dual-mass flywheel weighs 24.2 lbs. This heavyweight component favors dampened vibrations and smooth gear changes—not performance. The 16.5 lb. E34 M5 flywheel designed by ECS omits the bulky dual-mass design for a single-mass, chromoly steel flywheel. For the performance-minded enthusiast, this translates to quicker RPM changes, easier "heel-toe" downshifts, and improved acceleration.

Engineered in-house with the enthusiast in mind, this is the perfect option for those wanting a lightweight flywheel and performance clutch, without the heavy pedal feel commonly associated with aggressive clutch kits. The ECS S54 performance clutch and lightweight flywheel are designed to accommodate all conditions: from Sunday drives through the country to the abuse of the track. No matter your driving style or ability, this is the flywheel and clutch kit for you.

PART DESIGN

ECS S54 Performance Clutch Kit:

Compatible with any performance flywheel that is designed to accept an E34 M5 architecture clutch Sprung-hub clutch disc Includes ECS performance pressure plate, performance clutch disc, throwout bearing, pilot bearing, alignment tool, and all flywheel and pressure plate hardware ECS Single-Mass Lightweight Flywheel:

Eliminates the factory dual-mass flywheel for: Improved throttle response Improved acceleration Lower replacement cost Hardened 4140 Chromoly Steel for excellent engagement feel and wear resistance Zinc-plated for added corrosion resistance Weighs in at just 16.5 lbs! SFI tested and certified to ensure safe operation under all conditions Why is SFI testing and certification important?

The SFI Foundation, Inc. (SFI) is a non-profit organization established to issue and administer standards for the quality assurance of specialty performance and racing equipment. SFI certification indicates a flywheel has been certified using industry-standard SFI Spec 1.1 standards by an independent testing body to ensure the quality of both design and materials for flywheels utilized in competitive motorsports.

Having successfully passed SFI certification, this flywheel has an individual SFI serial number found in a laser etching, and on an affixed sticker. This certification means the ECS-engineered flywheel is safe and reliable during the rigors of competitive racing; it's also safe and reliable for years and years of street use.

PRODUCT DEVELOPMENT

This Performance Clutch Kit & Lightweight Flywheel was designed, engineered, tested, and quality inspected by the ECS Research and Development team. ECS Tuning strives for the highest level of precision and quality through leading-edge product development technology, including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing an in-house 3D printer, and rigorous long-term product testing.