BMW Drivetrain Parts for BMW 3 Series E46 (1999-2005)

Don't neglect your motor mounts! Most stock BMW motor mounts are fluid filled and the stiffness of the mount depends on this fluid. But over time the fluid leaks out and the strength of the mount is greatly reduced. A worn motor mount allows the engine to twist and shift around. The harder you're driving the more shift will occur. As the engine is moving around it can contact other parts in the engine bay - usually cooling related. The mechanical fan can hit the radiator; the A/C compressor can hit a radiator hose, the exhaust will flex and may break. Twisting of the engine can also lead to shifting problems as the transmission twists with it. There are countless issues related to worn or compressed motor mounts so don't overlook these as a regular replacement item (every 50,000 miles).

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
E46 Non-M
E85 Z4 2.5i/3.0i/3.0si
E89 Z4 3.0si

Tired of dealing with excess shifter slop and a mushy shifter? The Turner Shifter Rebuild & Upgrade Kits will restore your shifter's crisp feel and eliminate excessive movement that develops over time with wear. Included in this kit are all the common wear components and OE quality bushings that will give you a tighter shifting feel and will hold up like a day 1 BMW.

This kit is perfect to restore your driving pleasure!

See the included components under Kit Contents below.

If your clutch switch is bad, it will prevent the car from starting and seem similar to a bad starter, you will turn the key and nothing will happen. Replace yours to start your vehicle again.

Genuine BMW Module, Clutch Switch
This item fits the following BMW Chassis:
E39 M5,E46 M3,E85 Z4M,E39,E46,E85 Z4,E86 Z4
 

Shifter slop is a common complaint among all BMW models. Some of that play comes from the bushings where the shifter carrier mounts to the transmission. The original rubber carrier bushings don't last very long and when they get too soft the shifter flops around. These Teflon bushings are not as stiff as Delrin so they won't transmit as much vibration and buzz in the shifter. Yet Teflon will last much longer than the factory rubber, giving you precise shifting for many years.

Note: this is only one part of the shift linkage and there may be other components that need replacing to improve shifting feel.

We advise getting a replacement bushing carrier pin as well. If the original rubber bushings are worn the pin will have wear too and you will still have slop in the shifter, even with the new bushings.

These are the ROUND shifter carrier bushings (some BMW models have oval bushings).

This item fits the following BMWs:
6/1986-1992 E30 BMW 318i 318is 325e 325es 325i 325is 325ic M3
1992-1999 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic
1999-2006 E46 BMW 323i 323ci 325i 325ci
1982-1988 E28 BMW 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 535i M5

It only takes a gust of wind to have your hood crashing down on your head, or if you have a carbon fiber hood and no longer have the gas struts than this could be what you need.

 This hood prop is adjustable, lightweight, and sturdy making it easy to keep out of the way in the trunk so it's there whenever you need it. 

One of the most satisfying upgrades you can make to your BMW is to its factory shifter mechanism. By reducing the shifter's throw, you can give your manual transmission BMW a sportier, more precise feel. However, with so many different "short shift kits" out there, how can you be sure you're making the right decision? With the introduction of the Rogue Engineering OCTANE short shift kit, the choice is now crystal clear!

Rogue Engineering refuses to compromise with "lever substitution" as a method of short shift kit development. Rather than using actual test vehicles for their products, some companies actually dig through OEM factory parts diagrams to determine which factory levers can be substituted with others. This "lever substitution" method of introducing product is unacceptable. These shift kits have been developed and perfected through years of experience in proven short shifter technology, by Co-Founder, Ben Liaw. As longtime BMW enthusiasts know, Ben was single-handedly responsible for introducing and developing the idea of affordable, BMW factory-like, short shift kits for late model BMWs (BL/SS for those young enough to remember!). 

Rogue Engineering idea of a short shift kit is not substituting levers in place of factory ones just because "they fit". Throughout the 80s until recently, BMW was notorious for using only a few specific shifter levers for their manual transmission vehicles. For other companies, making just a few "replacement levers" and offering them in place of those factory part numbers was an easy way of calling it a short shift kit. Unfortunately, for those companies, BMW started using many different part numbers making it more difficult to just "swap in a lever".

Rogue Engineering only develops it's short shift kit with test vehicles in their facility, testing numerous prototypes, offering others to test it before settling on its final design. They feel that this old school, real world testing is the best way when modifying OEM ergonomic, sensory-based controls.