BMW Engine Parts for BMW 3 Series E46 (1999-2005)

ARP Connecting Rod Bolt Set - S54 (M10, 02/2003- Production) ...

For vehicles with production from 02/2003

T#:2206

Part#: 201-6102

In Stock

$ 119.99

This product was last offered at the strikethrough price on
10-01-2026

$ 116.99 USD

Add to Wish List

Qty

$ 116.99 USD

Add to Wish List

Set of 12 ProSeries ARP2000 connecting rod bolts for the Euro-spec M3 engine. Made by ARP, the world leader in fastener technology. The best rod bolts available for the Euro S50 and S54. Ideal for ultra high performance, racing & forced induction applications. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in professional motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods.

This set replaces the factory BMW Euro S50B30 and B32 rod bolts with part number 11-24-1-317-184 (11241317184) and 11-24-1-405-890 (11241405890). It's also used for S54 engines with stock M10 sized rod bolts, which were used from February 2003 production and later. It was also used in earlier engines that had connecting rods replaced. For these 2001-2003 models there is no easy way to check if the rods were replaced, except by checking the rod bolt diameter. If your car has the earlier M11 sized bolt, use ARP kit #201-6103 . Before opening the ARP kit, we recommend that you check your existing rod bolt size as BMW was not consistent with their applications. ARP bolts are not returnable if the package has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1993-1999 E36 BMW Euro M3
2001-2/2003 E46 M3 coupe / convertible*
2/2003-2006 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe*
2006-2008 MZ4 M Roadster & M Coupe
* - these engines could have either M10 or M11 sized bolts. If the rods and rod bearings were replaced under recall by BMW it should have the newer M10 bolts and this is the correct ARP set to order.

Show More Show Less

ARP Connecting Rod Bolt Kit - M52, M54B30, N20, N26, N54, N55, B46, B...

T#:3315

Part#: 201-6303

In Stock

$ 212.99

This product was last offered at the strikethrough price on
10-12-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the 47mm length factory BMW rod bolts with part number 11-24-7-589-671 (11247589671) Check applications before ordering! Opened ARP bolt kits are not
returnable.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1999-2005 E46 BMW 328i 328ci 330i 330ci 330xi
2001-2003 E39 BMW 530i
2004-2005 E60 BMW 530i
2004-2006 E83 BMW X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 3.0i
2003-2005 Z4 BMW Z4 3.0i

Show More Show Less

ARP Steel Block Head Stud Kit for M50/M52 & S50/S52 (US Spec) ...

T#:3606

Part#: 201-4302

In Stock

$ 240.99 USD

Add to Wish List

Qty

$ 240.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found for the E36 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines (steel block only)
1992-1995 M50 6 cylinder including 325i, 325is and 525i
1996-1999 M52 6 cylinder including 328i, 328is, 323is, 528i
1995-1995 S50US 3.0 liter including 1995 M3 (US only)
1996-1999 S52US 3.2 liter including 1996-1999 M3 (US) and MZ3

Show More Show Less

ARP Connecting Rod Bolt Kit - Early S54 - E46 M3, MZ3 (M11x47mm Size)...

For vehicles with production up to 02/2003

T#:2211

Part#: 201-6103

In Stock

$ 215.99 USD

Add to Wish List

Qty

$ 215.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

These bolts are M11 size to replace the stock M11 BMW bolt part number 11-24-7-834-310 (11247834310). The M11 bolt size was used in S54 engines up to 2/2003 production. However, most S54 engines up to that point had their rod bearings replaced under a factory recall and some may have had new connecting rods installed at the same time (or even a new engine altogether). The new bolts installed in these earlier engines are M10 size. Unfortunately, there is no way of knowing which rod or bolt is currently in your car (unless your car came with service records detailing when and what was replaced). The only sure way to know is to check the bolts currently installed in your engine. If yours was updated to the M10 sized bolt, use ARP kit #201-6102 . ARP bolts are not returnable if the pacakge has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
2001-2/2003 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe

Show More Show Less

ARP S54 Head Stud Kit (E46M3 / MZ3 / MZ4)

T#:3631

Part#: 201-4303

Ships in 3 Business Days

$ 247.99 USD

Add to Wish List

Qty

$ 247.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs, particularly on the S54 3.2 liter engine. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best S54 head studs we've found for the E46 M3 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines
2001-2006 E46 M3 coupe & convertible
2001-2002 MZ3 M Roadster & M Coupe (with S54 engine)
2006-2008 MZ4 Z4 M Roadster & M Coupe

Show More Show Less

Rogue Engineering Stainless Steel S54 Vanos Line - E46 M3, Z3 M, Z4 M...

T#:567568

Part#: S54VAN

Back Ordered

$ 59.00 USD

Add to Wish List

Qty

$ 59.00 USD

Add to Wish List

Now that BMWs popular S54 engine (found in the 2001-06 BMW M3, 2001-02 MZ3 and 2007-08 MZ4) are getting older, it's important to keep an eye on particular items. One such point is the S54 Vanos oil line. Normally thought of as a worry-free item, it has proven to put the damper on many track days. Rogue's stainless steel braided VANOS line replaces the factory BMW part number 11367837614 (current MSRP from BMW is $128.08!) The high pressure (1200psi) control system of the S54 vanos system is used to ensure responsive and accurate camshaft adjustments. The added complexity of the high oil pressure used on the S54 vanos means more opportunities for failures. Some customers have encountered the high pressure hardline fail at the track, spraying oil all over their engine compartment, ending their day. Rogue Engineering's S54 Vanos Oil Line is built in their Upper Saddle River, NJ facility, and tested to over 3000psi. Using their stainless steel braided hose with the proper banjo fittings, this a direct replacement for the factory line. Like the factory line, the lower portion of the line uses a heat sleeve from additional heat from the VANOS pump itself. Fits the following BMWs: 2001-06 BMW E46 M3 2001-02 BMW MZ3, including coupe and convertible 2007-08 BMW MZ4, including coupe and convertible

Show More Show Less

Ferrea Performance Intake Valve - Stock Size

T#:583445

Part#: F1550P

Back Ordered

$ 34.99

This product was last offered at the strikethrough price on
11-04-2026

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

M52, M54, S50, S52 H-Beam Connecting Rods - Eagle

T#:640320

Part#: CRS5313B63D

In Stock

$ 619.99

This product was last offered at the strikethrough price on
11-04-2026

$ 611.99 USD

Add to Wish List

Qty

$ 611.99 USD

Add to Wish List

Eagle is synonymous with exceptional quality and unwavering commitment to customer satisfaction, which has cultivated a loyal and satisfied customer base. This dedication has propelled Eagle to unparalleled growth throughout the years, expanding their product range to include crankshafts and a wider selection of connecting rods. Key Benefits: Proven Excellence: Eagle's reputation as the largest and most respected aftermarket connecting rod and crank manufacturer underscores their commitment to excellence. Continuous Advancements: Eagle's relentless pursuit of perfection is evident in their continuous design enhancements, materials innovation, and manufacturing techniques, ensuring their products are always at the forefront of performance. Lightweight Design: Eagle prioritizes making their products lighter, enhancing your engine's performance while maintaining structural integrity. Strength and Durability: Every Eagle connecting rod is engineered for superior strength, ensuring your engine can handle high-performance demands without compromise. Efficient Manufacturing: Eagle's dedication to efficiency guarantees that each connecting rod is manufactured with precision and attention to detail, resulting in top-notch quality. Diverse Applications: With a diverse product range, Eagle ensures compatibility with a wide variety of engines, making their connecting rods a versatile choice for automotive enthusiasts.

Show More Show Less

ARP Connecting Rod Bolt Kit - E36 M3 S50/S52 (US only), E46 323/325 ...

T#:2210

Part#: 201-6201

Ships in 7 Business Days

$ 222.99

This product was last offered at the strikethrough price on
08-13-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the factory BMW rod bolt number 11-24-1-739-728 (11241739728) which measures 44mm in length. The 44mm BMW rod bolt was used on all US spec E36 M3 (3.0 and 3.2 liter), 1999-2000 E46 323i/323Ci, 2001-2005 325i/325Ci, Z3 1.9,2.5 and 3.2, as well as Z4 2.5. It was also used on SOME of the M50 2.5 liter engines from 1992-1995 -- but check before ordering! Opened ARP bolt kits are not returnable. If your M50 2.5 liter engine has 53mm rod bolts, you will require kit part# 201-6301 instead.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1992-1995 E36 325i/is *** with 44mm rod bolts only ***
1995-1995 E36 M3 S50 3.0 liter (US model)
1996-1999 E36 M3 S52 3.2 liter (US model)
1999-2000 E46 323i & 323Ci (US)
2001-2005 E46 325i, 325xi & 325Ci (US)
1998-2002 Z3 2.3 / 2.5 liter
1998-2000 MZ3 M Roadster & M Coupe
2003-2005 Z4 2.5 liter
*** DOES NOT FIT E36 328 ****

Show More Show Less

ARP Main Stud Kit for S54 (E46M3 & Z4M)

T#:2192

Part#: 201-5002

In Stock at Vendor

$ 171.99 USD

Add to Wish List

Qty

$ 171.99 USD

Add to Wish List

This ARP main stud set is for the S54 3.2 liter, as found in all 2001 to 2006 E46 M3, as well as the 2006-2008 Z4 M Roadster and M Coupe models. Switching to the ARP main stud kit eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This S54 main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This ARP main stud kit fits the following BMWs:
2001-2006 E46 M3 3.2 liter coupe/convertible
2001-2002 MZ3 M Coupe & M Roadster (S54 engine)
2006-2008 MZ4 M Coupe & M Roadster

Show More Show Less

Rogue Engineering Power Pulley Set - S54 - E46 M3, Z3/Z4 M

T#:553971

Part#: PP.S54

Ships in 4 Business Days

$ 259.00 USD

Add to Wish List

Qty

$ 259.00 USD

Add to Wish List

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4

Show More Show Less

Ferrea Performance Exhaust Valve - Stock Size

T#:583444

Part#: F1552P

Ships on Dec 1, 2026

$ 34.99

This product was last offered at the strikethrough price on
11-04-2026

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

OMP Battery Cut Off Switch / Kill Switch

T#:1614

Part#: EA-462

Back Ordered

$ 65.00 USD

Add to Wish List

Qty

$ 65.00 USD

Add to Wish List

OMP Battery Cut Off Switch / Kill Switch, for use in racecars as an emergency "kill switch", to depower the electrical system in the event of a crash or other emergency. This cut off switch is FIA approved, has 6 poles and alternator protection, as well as a removable key.

Show More Show Less

Active Autowerke Rotrex Traction Fluid - 1 Liter

T#:57616348

Part#: RTF-1L

Ships in 3 Business Days

7% off MSRP $ 140.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 130.00 USD

Add to Wish List

Qty

7% off MSRP

$ 140.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 130.00 USD

Add to Wish List

Rotrex superchargers utilize a unique traction drive system that sets it apart from other centrifugal-style superchargers. For best performance, Rotrex recommends replacing this fluid every 50,000 miles. This bottle of traction fluid is plenty enough for one supercharger service (typically 750ml).

Show More Show Less

Active Autowerke - S54 Supercharger Kit (Level 1) - E46 M3 (Manual Tr...

For vehicles with 6 speed transmissions

T#:397296

Part#: 12-023

Ships in 10 Business Days

5% off MSRP $ 11,249.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 10,686.99 USD

Add to Wish List

Qty

5% off MSRP

$ 11,249.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 10,686.99 USD

Add to Wish List

Since getting their start in 1981, Active Autowerke has earned a well-respected reputation in the BMW community for engineering high-quality power solutions for popular BMW models. This supercharger kit will produce 525 horsepower and 335 ft.lbs. of torque on your BMW, while retaining platform integrity and daily driveability. Unique to the design of the Rotrex supercharger is the traction drive system, which eliminates the lag often found in other centrifugal supercharger setups. Power delivery is smooth and dependable, and 100% reversible to stock if you so choose, since each system is designed as a self-contained unit.

Kit features:

Rotrex 92 trim supercharger running 7 PSI of boost
Supercharger bracket, pulleys, & belt
Self-contained oiling system with front-mount oil cooler
6 high-flow fuel injectors
Colder heat range spark plugs
Active Autowerke Generation 7 intake manifold with dual bypass valve
Front mount air-to-air intercooler
Active Autowerke air filter
Active Autowerke dyno-tuned software
All mounting hardware, plumbing, hoses, & clamps
Illustrated instruction manual & installation guide
2 year warranty with free tech support

Performance Specs:

Power : 525 BHP @ 7650 rpm
Torque : 335 ft/lbs @ 5400 rpm
Boost Level : 7-8 psi

Show More Show Less

BMW Rod Bolt Stretch Gauge with Billet Body & Thumb Hold

T#:4309

Part#: 100-9942

In Stock at Vendor

$ 216.99 USD

Add to Wish List

Qty

$ 216.99 USD

Add to Wish List

We highly recommend using a stretch gauge when installing rod bolts and other fasteners, where it is possible to measure the length of the fastener.

Rogue Engineering Power Pulley - E46 (Non-M)

T#:554021

Part#: P.E46

Special Order: No Guaranteed ETA

$ 225.00 USD

Add to Wish List

Qty

$ 225.00 USD

Add to Wish List

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

Fits the following BMWs:
2000-2006 E46 BMW 323/325/328/330

Show More Show Less

Rogue Engineering Racing Power Pulley Set - S54 - E46 M3, Z3/Z4 M ...

T#:553959

Part#: PP.S54.RACE

Ships in 9 Business Days

$ 599.00 USD

Add to Wish List

Qty

$ 599.00 USD

Add to Wish List

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4

Show More Show Less

Main Stud Kit - M50/M52/S50/S52

T#:26171653

Part#: ARP-MSK-M50

Back Ordered

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

This ARP Main Stud Kit is designed to replace BMW 11111735525 for the M50/M52/S50/S52 engines that were used in a variety of BMW models. One significant advantage of these main studs is their ability to prevent main cap walk, which can occur when the main caps shift or move out of position, potentially causing damage to the engine. In addition, ARP Main Studs can safeguard the threads of your engine block, providing an extra layer of protection against potential damage. When opting for main studs instead of factory bolts, it's important to note that the engine builder should mic the bores. Using studs may require a line hone to ensure proper fitment and alignment. A line hone is a machining process that can be used to resize and reshape the main bearing bores, ensuring that they are perfectly round and concentric. This is crucial for ensuring proper oil clearance and preventing premature bearing wear. By mic'ing the bores and performing a line hone if necessary, engine builders can ensure that the main studs are installed correctly and that the engine will perform reliably and at its best. Installation Instructions: To ensure accurate torque readings and proper thread engagement, thoroughly clean all threads in the engine block. If necessary, use an ARP chaser to chase the threads. Before installing any hardware, carefully inspect and clean it for defects, shipping damage, and proper fit, length, and dimension. Gently screw the main studs into the engine block by hand until they are snug. Install the main caps, checking for any binding or misalignment. Apply ARP Ultra-torque fastener assembly lubricant to the threads of the studs, nuts, and washers. Install the washers and nuts onto the studs and tighten them by hand. It is highly recommended to use the ARP Ultra-torque fastener assembly lubricant provided with the kit, as it provides consistent clamping force and reduces friction on the studs. Do not use motor oil or other low-quality lubricants. PRELOAD (TORQUE) RECOMMENDATIONS 7. Following the manufacturer-recommended torque sequence tighten the nuts in steps 1-3 Step 1: Tighten to 20 ft-lbs. Step 2: Tighten to 40 ft-lbs. Step 3: Tighten to 60 ft-lbs. With the included ARP Ultra-Torque fastener assembly lubricant

Show More Show Less

ARP Ultra-Torque Fastener Assembly Lubricant (Select Your Size) ...

T#:338571

Part#: TMS1733

In Stock

Starting at $ 1.99 USD

Add to Wish List

Starting at $ 1.99 USD

Add to Wish List

If you are using a premium fastener, such as the ARP brand rod bolts, head bolts, or main bolts, then you will want this assembly lube. Made to be used to precisely duplicate all ARP fastener preload specifications.

Show More Show Less

Active Autowerke PRIMA Supercharger Kit - E46 M3 (6 Speed Transmissio...

T#:397295

Part#: 12-021

Ships in 10 Business Days

5% off MSRP $ 9,375.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 8,906.99 USD

Add to Wish List

Qty

5% off MSRP

$ 9,375.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 8,906.99 USD

Add to Wish List

Since getting their start in 1981, Active Autowerke has earned a well-respected reputation in the BMW community for engineering high-quality power solutions for popular BMW models. This supercharger kit will produce 425 horsepower and 295 ft.lbs. of torque on your BMW, while retaining platform integrity and daily driveability. Unique to the design of the Rotrex supercharger is the traction drive system, which eliminates the lag often found in other centrifugal supercharger setups. Power delivery is smooth and dependable, and 100% reversible to stock if you so choose, since each system is designed as a self-contained unit. best of all, when you crave more power, this kit is fully upgradeable to Level 1 and Level 2 specs.

Kit features:

Rotrex C38-92 trim supercharger running 5.8 PSI of boost
Active Autowerke GEN 7 intake manifold
Active Autowere dual blow-off valve setup
Active Autowerke Air Filter
Alpha N software tune w/ SIMON2 interface
6 high-flow fuel injectors
Dedicated oil cooling system
All mounting hardware, plumbing, hoses, & clamps
Illustrated instruction manual & installation guide
2 year warranty with free tech support

Base Prima supercharger Dynojet results:
Boost: 5.8 psi
Stock Horsepower: 285.4 WHP @ 7500 RPM
Stock Torque: 232.36 LB-FT @ 5250 RPM
Supercharged Horsepower: 426.69 WHP @ 8150 RPM
Supercharged Torque: 297.99 LB-FT @ 7200 RPM

Show More Show Less

Active Autowerke PRIMA Supercharger Upgrade Kit to PRIMA Plus - E46 M...

T#:397299

Part#: 12-022

Ships in 10 Business Days

5% off MSRP $ 2,249.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 2,136.99 USD

Add to Wish List

Qty

5% off MSRP

$ 2,249.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 2,136.99 USD

Add to Wish List

As the producer of one of the finest working supercharger systems for the BMW E46 M3, Active Autowerke is proud to introduce the PRIMA PLUS supercharger system capable of exceeding 500 WHP running on pump drawn 93 octane. The PRIMA PLUS is an upgrade kit to the existing PRIMA supercharger system designed to create MORE horsepower. In collaboration with Frank Smith of Tuning Tech FS, the Prima PLUS SC kit has evolved as a fantastic performer. With numerous dyno runs under countless hours all monitored through careful Data Logging and Lean/Rich evaluation, this PRIMA PLUS supercharger kit is ready for the BMW enthusiast. The PRIMA PLUS is a centrifugal design supercharger using a conventional fixed drive pulley, but unlike its predecessors, the PRIMA PLUS also has variable boost settings of 9.0 psi and 9.5 psi to help attain the power. A first in the BMW forced induction industry. For easy comparisons, here is where the PRIMA and PRIMA PLUS + stands when measuring rear wheel horsepower. A stock BMW E46 M3 is around 265 WHP. | PRIMA SC makes 425 WHP. | PRIMA PLUS SC makes 500+ WHP.

Show More Show Less

Active Autowerke Supercharger Kit - E46 M3

T#:340093

Part#: AASC-E46M3

Back Ordered

Starting at $ 7,995.00 USD

Add to Wish List

Starting at $ 7,995.00 USD

Add to Wish List

Race on Sunday, to sell on Monday. This old saying is indicative of the new Generation 8 supercharger system for the E46 M3. Through countless hours of testing, it has often been quoted that the true test has always been a race environment. What better venue than Brock Yates One Lap of America Race. With a rigorous 7,000 miles to be covered within a week, and to compete against the likes of Porsches, Corvettes, Nissan GTRs, this would be the testing grounds for the new Generation Active Autowerke Supercharger system. The Active Autowerke Generation 8 Supercharger System not only proved its worth by being the highest ranked BMW within the field, but also ranked 1st in its class..

The data and technology that made this winning combination is now being applied in the new Generation 8 of the Active Autowerke supercharged E46 M3 level 1. Reliability and power is needed if you want to be on the podium, and this new Generation 8 will deliver exactly that. Consistent, repeatable runs of over 415 WHP (525 engine horsepower) were also recorded on the Active Autowerke chassis dyno in hot 94 + degree Fahrenheit conditions with humidity in the 60% + range. These run conditions might be considered a deterrent and not really suited, but it is better knowing the horsepower numbers are under such conditions, since higher horsepower numbers will only increase as the temperature falls and the air becomes more dense.

Stage 1 Performance Specs:
Power : 525 BHP @ 7650 rpm
Torque : 335 ft/lbs @ 5400 rpm
Boost Level : 7-8 psi

Key Features:

Rotrex 92 Trim Supercharger

Active Autowerke Gen 7 Intake Manifold w/ Dual By Pass Valve

Front Mount Air to Air Intercooler

Turbo like speed with linear power delivery

Large Fuel Injectors

Supercharger Oil Cooler

Colder Heat Range Spark Plugs

High Performance AA Spec Green Filter

Active Autowerke High Performance Software

All Mounting Hardware, plumbing, hoses and clamps

Proven Horsepower gains even under extreme conditions

Installation Instructions included

2 Year Limited Warranty
Want even more power? Upgrade to the Stage 2 kit with Larger Intercooler & Fuel System.
The stage 2 System boosts the S54's power output to over 600BHP and includes an upgraded fuel system (includes two fuel pumps, fuel filter, all new -6 lines, fuel pressure regulator, dead end fuel rail, upgraded injectors and all required fittings). This ugpraded fuel system is a must once reaching these increased boost levels due to the fact that the factory fuel system is simply inadequate at this level. The stage 2 system also use a larger front mount air to air intercooler and the Active Autowerke custom methanol injection system. NOTE: Level 2 supercharger system is designed and engineered to operate in conjunction with the Active Autowerke Water/Methanol system as an integral part of the kit. Reasons to incapacitate, isolate, turn off, or not installing this system can and will void all warranty and related claims associated to the proper function of the specified Active Autowerke supercharger system.

Stage 2 Performance Specs:
Power � : � 605 BHP @ 7000 rpm
Torque � : � 395 ft/lbs @ 5400 rpm
Boost Level � : � 11-12 psi

Custom built to order. Please allow 2-3 weeks for delivery.

This item fits the following BMWs:
2001-2006 E46 BMW M3, M3 Convertible

Show More Show Less

Supercharger Kit Level 1 - E46 330 2003+

For model years 2003+ ~ Call in to provide vin before purchase

T#:50899201

Part#: 12-016M45

Ships in 10 Business Days

$ 9,856.00 USD

Add to Wish List

Qty

$ 9,856.00 USD

Add to Wish List

Add proven forced induction performance to your E46 330i with the Active Autowerke Supercharger Kit. Designed to deliver a significant horsepower increase without sacrificing daily usability, this system operates safely on 91 to 93 octane pump fuel and integrates directly with the factory ECU. Active Autowerke’s dyno developed calibration manages ignition timing, fueling, VANOS function, and rev limits through the stock DME for consistent, predictable results. Power delivery remains smooth and repeatable with OEM like drivability, and the system can be returned to stock configuration if needed. The included self contained oil cooling circuit keeps installation straightforward without modifying the factory oil system. For E46 owners seeking a complete, well engineered bolt on solution, this kit offers substantial, reliable gains. Key Features Rotrex C38-81 trim supercharger 8 PSI boost pressure CNC machined supercharger bracket with hardware Self contained oil system with front mount oil cooler Six higher flow fuel injectors Active Autowerke/Bosch bypass valve High temperature silicone hoses with stainless clamps Mandrel bent aluminum tubing for improved flow Active Autowerke performance air filter (K&N on select models) Active Autowerke dyno tuned software Complete mounting hardware, plumbing, hoses, and clamps Illustrated installation manual and guide 1 year warranty with technical support Performance Specifications Power: 320 BHP @ 7000 RPM Torque: 260 lb ft @ 5400 RPM Boost Level: 8.0 PSI

Show More Show Less

E46 M3 Prima Plus + Supercharger With 600HP Upgrade Kit

For SMG Transmissions Only ~ Call in to provide vin before purchase

T#:50934251

Part#: V12-035S

Ships in 10 Business Days

$ 10,449.00 USD

Add to Wish List

Qty

$ 10,449.00 USD

Add to Wish List

As producer of one of the finest working supercharger systems for the BMW E46 M3, Active Autowerke is proud to introduce the PRIMA PLUS supercharger system capable of exceeding 500 WHP running on pump drawn 93 octane. The PRIMA PLUS is an upgrade kit to the existing PRIMA supercharger system designed to create MORE horsepower.

Show More Show Less

Supercharger Kit Level 1 - E46 328 '99-'02

For model years 1999-2002 ~ Call in to provide vin before purchase

T#:50899197

Part#: 12-016M438

Ships in 10 Business Days

$ 9,856.00 USD

Add to Wish List

Qty

$ 9,856.00 USD

Add to Wish List

Add proven forced induction performance to your E46 with the Active Autowerke 328i Supercharger Kit. Engineered to work seamlessly with your factory ECU and 91 to 93 octane pump fuel, this system uses dyno developed software to precisely manage ignition timing, fueling, VANOS, and rev limits through the stock DME. The result is smooth, repeatable power delivery with OEM-like drivability and the ability to return the vehicle to stock if desired. A self contained oil cooling system keeps installation clean without interfering with the factory oil circuit. For E46 owners looking to approach M3 level performance without the full swap, this complete bolt-on solution delivers substantial gains with proven reliability. Key Features Rotrex C38-81 trim supercharger 8 PSI boost pressure CNC machined supercharger bracket with hardware Self contained oil system with front mount cooler Six higher flow fuel injectors Active Autowerke/Bosch bypass valve High temperature silicone hoses with stainless clamps Mandrel bent aluminum charge tubing Active Autowerke performance air filter (K&N on select models) Active Autowerke dyno tuned software Complete hardware and illustrated instructions 1 year warranty with tech support Performance Power: 320 BHP @ 7000 RPM Torque: 260 lb ft @ 5400 RPM Boost: 8.0 PSI

Show More Show Less

PRIMA Supercharger Kit (Non-Intercooled) - E46 M3

For SMG Transmissions Only ~ Call in to provide vin before purchase

T#:50899202

Part#: 12-021S

Ships in 10 Business Days

$ 8,906.00 USD

Add to Wish List

Qty

$ 8,906.00 USD

Add to Wish List

Co-developed with Frank Smith of TuningTechFS, the Active Autowerke PRIMA Supercharger Kit delivers a proven entry point into forced induction for the E46 M3. The system is engineered around efficiency, repeatability, and upgrade potential, with a baseline configuration that can grow beyond 500 WHP through available Level 1 and Level 2 packages. PRIMA focuses on clean, practical design. This is a fully bolt-on, non intercooled setup that installs without custom fabrication and can be reverted to stock if required. The modular architecture also allows straightforward progression to higher output configurations. As expected from Active Autowerke, the kit enhances overall performance while preserving the sharp throttle response and balanced character of the S54-powered M3. PRIMA Supercharger Kit Key Features Rotrex C38-92 supercharger assembly Active Autowerke GEN 9 intake manifold plenum Active Autowerke dual blow off valve configuration Active Autowerke green performance filter with cover Alpha N calibration with SIMON 4 interface included High capacity fuel injectors Colder heat range spark plugs Dedicated self contained oil cooling circuit Pre assembled hoses, clamps, and installation hardware Compatible with Level 1 and Level 2 upgrade paths Baseline Dynojet Results Boost: 5.8 PSI Stock Power: 285.4 WHP @ 7500 RPM Stock Torque: 232.36 lb ft @ 5250 RPM Supercharged Power: 426.69 WHP @ 8150 RPM Supercharged Torque: 297.99 lb ft @ 7200 RPM

Show More Show Less

Supercharger Kit Level 1 - E46 3330i

For model years 1999-2002 ~ Call in to provide vin before purchase

T#:50899198

Part#: 12-016M430

Ships in 10 Business Days

$ 9,856.00 USD

Add to Wish List

Qty

$ 9,856.00 USD

Add to Wish List

Add proven forced induction performance to your E46 330i with the Active Autowerke Supercharger Kit. Designed to deliver a significant horsepower increase without sacrificing daily usability, this system operates safely on 91 to 93 octane pump fuel and integrates directly with the factory ECU. Active Autowerke’s dyno developed calibration manages ignition timing, fueling, VANOS function, and rev limits through the stock DME for consistent, predictable results. Power delivery remains smooth and repeatable with OEM like drivability, and the system can be returned to stock configuration if needed. The included self contained oil cooling circuit keeps installation straightforward without modifying the factory oil system. For E46 owners seeking a complete, well engineered bolt on solution, this kit offers substantial, reliable gains. Key Features Rotrex C38-81 trim supercharger 8 PSI boost pressure CNC machined supercharger bracket with hardware Self contained oil system with front mount oil cooler Six higher flow fuel injectors Active Autowerke/Bosch bypass valve High temperature silicone hoses with stainless clamps Mandrel bent aluminum tubing for improved flow Active Autowerke performance air filter (K&N on select models) Active Autowerke dyno tuned software Complete mounting hardware, plumbing, hoses, and clamps Illustrated installation manual and guide 1 year warranty with technical support Performance Specifications Power: 320 BHP @ 7000 RPM Torque: 260 lb ft @ 5400 RPM Boost Level: 8.0 PSI

Show More Show Less

Active Autowerke E46 M3 Prima Plus + Supercharger With 600HP Upgrade ...

T#:401508

Part#: 12-035

Ships in 10 Business Days

$ 8,359.99 USD

Add to Wish List

Qty

$ 8,359.99 USD

Add to Wish List

As producer of one of the finest working supercharger systems for the BMW E46 M3, Active Autowerke is proud to introduce the PRIMA PLUS supercharger system capable of exceeding 500 WHP running on pump drawn 93 octane. The PRIMA PLUS is an upgrade kit to the existing PRIMA supercharger system designed to create MORE horsepower.

Show More Show Less

M9 X 1.25 BMW 328 E46 Rod Bolt Kit

T#:54139644

Part#: 301-6022

Ships on Dec 1, 2026

20% off MSRP $ 19.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.99 USD

Add to Wish List

Qty

20% off MSRP

$ 19.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.99 USD

Add to Wish List

Engineered from proprietary ARP2000® alloy, these M9 x 1.25 fasteners provide the massive clamping force needed to keep the rod journals perfectly round and seated, even when bouncing off the rev limiter lap after lap.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW 3 Series E46 (1999-2005)

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results