BMW Engine Parts for BMW 3 Series E46 (1999-2005)

This set of top-end gaskets is a both a time and money saver. It includes all of the commonly replaced gaskets, seals, and o-rings when pulling the cylinder head for overhaul. Having these on hand instead of chasing them down at the last minute will save you time, money, and frustration. With the head off the car you're going to want or need to replace these items anyway to ensure it's free of fluid and vacuum leaks. This is especially important because the newer BMW models have very strict emissions controls and vacuum and oil leaks can create turmoil in the system. Even if you're not pulling the head this set includes so many valuable parts you'll want to keep this on hand to use for spares.

This item fits the following BMWs:
2003-2006 E46 BMW 325i 325ci 325xi 330i 330ci 330xi
9/2002-on E39 BMW 525i 530i
2004-2005 E60 BMW 525i 530i
2004-2006 E83 BMW X3 2.5i X3 3.0i
2003-2006 E53 BMW X5 3.0i
9/2002-on Z3 BMW Z3 2.5i Z3 3.0i
2003-2006 E85 BMW Z4 2.5i Z4 3.0i

This top-end gasket set covers the cylinder head on the S54 engine used in the E46 M3, Z3 M Roadster/M Coupe, and E85/E86 Z4 M Roadster, M Coupe. If you're pulling the head, intake manifold, or doing any other upper end engine work this set can be a time and money saver. This set includes all of the commonly replaced gaskets, seals, and o-rings when overhauling the head. It's also a useful kit to have and dip into any time you're doing upper end engine work. Not having a critical seal or gasket on hand can ruin your work and this gasket set can prevent that from happening. This Victor Reinz set includes the head gasket.

BMW #QtyDescription

071199035461left timing rail upper bolt seal

071199630724VAN0S oil line seal ring

071199631292crankcase vent banjo bolt seals

071199632522screw plug seal ring

071199633421right upper timing rail bolt seal ring

071199634181timing chain tensioner seal ring

111214373952valve cover stud grommet seal

1112783097213valve cover stud grommet seal

111278312716spark plug hole profile gasket

111278320341main valve cover gasket

111278370241oil fill cap seal ring

111278370251crankcaske oil separator seal ring

111417367581VAN0S-camshaft plate o-ring

111578309661crankcase oil separator o-ring, large

111578321191crankcase oil separator plug o-ring

113113173181inside o-ring for internal VAN0S regulating valve

113490644572valve stem seal, 2 sets = 24 valves

113678319381VAN0S unit profile gasket

114113060821outside o-ring for internal VAN0S regulating valve

115313184021thermostat-to-water pump o-ring

115378307083coolant pipe o-ring gasket

115378307092thermostat housing connector o-ring

116114076951intake bellows o-ring profile gasket

116178301041intake bellows-to-airbox gasket

116278306676exhaust manifold port gasket

117275052591air pump valve profile gasket

121417483982camshaft position sensor o-ring

135478314836throttle body o-ring

136414374746fuel injector o-ring, upper

136478306116fuel injector o-ring, lower

111278359181head gasket

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW Z3 M Roadster Z3 M Coupe
2006-2008 E85 BMW Z4 M Roadster Z4 M Coupe

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

Introducing the Innovate Motorsports MTX Digital Series "Dual Function" Gauges – now available! These 2 1/16" (52mm) gauges come with interchangeable faceplates and bezels, locking connectors for simplified installation, and MTS serial connections for seamless integration with other Innovate devices for data logging.

DISPLAY RANGE

• Ethanol Content %: 0-100%
• Temperature: -40-257 °F (-40-125°C)

KEY FEATURES

• Ethanol Content
• Error reporting for ethanol content sensor (Digital Display)
• Fuel Temperature
• Customizable exterior LED display
• Programmable exterior LED color options
• Selectable unit of measure in °F or °C
• Programmable fuel temperature warning (outer LED)
• 2-Configurable analog outputs
• Ethanol Content: 0v = 0%, 5v = 100%
• Fuel Temperature: 0v = -40 °F, 5v = 257 °F (-40-125°C)

MTX-D: Ethanol Content Percentage & Fuel Temp Gauge Kit includes Gauge (Black Faceplate, Black Bezel), Silver Bezel & White Faceplate, Harness, Program Cable (Serial), Ethanol Content Sensor, Quick Start Installation Guide.

Please note that this is a universal fitment gauge, and installation may vary depending on the vehicle.

The engine mounting points on the E46 are stamped sheet metal. Due to this construction, they are notorious for cracking and ripping out over time.

This kit welds onto the front subframe preventing cracks and failure of the engine mounting points. All reinforcement plates are precision laser cut from 14 gauge steel.

This kit includes:

2x top position weld-in reinforcement plates 2x lower position weld-in reinforcement plates