BMW Internal Engine Parts for BMW 3 Series E92 (2007-2013)

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

E9x M3 BE Bearings Performance Rod Bearing Replacement Kit

T#:5403237

Part#: 11247838088TMSKT

In Stock

$ 1,111.99 USD

Add to Wish List

Qty

$ 1,111.99 USD

Add to Wish List

Includes everything needed for a rod bearing service, featuring BE Bearings upgraded rod bearings. The S65 engine has a known history of rod bearing failure, and if your engine is higher mileage, don't let this catastrophic failure happen to you. Replace your rod bearings and prevent a spun bearing which can trash your crankshaft. BE Bearings, in conjunction with Clevite, an OE bearing manufacturer, have redesigned and manufactured the bearings for greater clearance and have changed the original material composition from tin-aluminum to lead-copper. This upgrade incorporated the state-of-the-art Clevite Tri-Metal design and featured a Tri-Armor™ coating. This allows for the additional lubrication for wear prevention, plus, the softer bearings are better for your engine and are more tolerant of foreign particles suspended in your oil. Another benefit from this is that the oil can now be sent for testing to accurately gauge the amount of wear occurring in the engine. Kit includes Upper and lower BE Bearings upgraded rod bearings Hardware Oil filter Castrol TWS Edge Professional 10W 60 Oil pan gasket RedLine assembly lube

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

T#:558795

Part#: VTT-CRANKHUB-1

Ships in 5 Business Days

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Genuine BMW Cylinder Head Gasket - N54 3.0L

1.215mm thickness - for use with an unmachined head

T#:22177

Part#: 11127557265

Ships in 1-2 days

13% off MSRP $ 233.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 202.99 USD

Add to Wish List

Qty

13% off MSRP

$ 233.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 202.99 USD

Add to Wish List

Genuine BMW Cylinder Head Gasket Asbestos-Free - 1,215Mm
This item fits the following BMW Chassis:
E82 1M Coupe,E71 X6,E82,E89 Z4,E90,E92,E93,F01,F02

Fits BMW Engines including:
N54,N54T

Show More Show Less

N52 Valvetronic Camshaft Adjuster Replacement Kit

T#:5416764

Part#: 11377548388TMSKT

Ships in 5 Business Days

Sale - Save 19% $ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.20 USD

Add to Wish List

Qty

Sale - Save 19%

$ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.20 USD

Add to Wish List

Includes new Valvetronic motor, gasket, and hardware. The Valv-tronic adjuster unit changes the the timing shaft to adjust the valve timing.

Genuine BMW Engine Block Fastener Set

T#:30558

Part#: 11110426591

In Stock

$ 136.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

Genuine BMW Set Of Aluminum Screws F Compl.Crankcase
This item fits the following BMW Chassis:
E82 1M Coupe,E71 X6,E82,E89 Z4,E90,E92,E93,F01,F02,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4 X4,F30,F32,F33,F34,F36

Fits BMW Engines including:
N51,N54,N54T,N55

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Rod Bearing Overhaul Kit - E9X M3 S65

T#:340426

Part#: TMS222795

Ships Today

$ 1,530.99

This product was last offered at the strikethrough price on
02-26-2026

Starting at $ 1,456.40 USD

Add to Wish List

Starting at $ 1,456.40 USD

Add to Wish List

Rod bearings should be replaced as a preventative measure before 80,000 miles. This package is the most complete rod bearing overhaul kit available and includes not just the latest BMW rod bearings and connecting rod bolts, but also everything else that should be replaced with the oil pan and front subframe off the car.

Show More Show Less

Genuine BMW Exhaust Valve 30,5/4,96mm - 11347838294 - E60 M5,E63 M6,E...

T#:34556

Part#: 11347838294

Ships in 5 Business Days

6% off MSRP $ 85.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 80.99 USD

Add to Wish List

Qty

6% off MSRP

$ 85.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 80.99 USD

Add to Wish List

Genuine BMW Exhaust Valve - 30,5/4,96mm
This item fits the following BMW Chassis:
E60 M5,E63 M6,E63,E90,E92,E93

Fits BMW Engines including:
S65,S85

Show More Show Less

Genuine BMW Crankshaft Position Sensor - N52 N54 S85 S65 S63 ...

T#:367850

Part#: 13627525015

In Stock

16% off MSRP $ 175.17

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 146.99 USD

Add to Wish List

Qty

16% off MSRP

$ 175.17

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 146.99 USD

Add to Wish List

This crankshaft position sensor (CPS) provides the engine computer with engine speed data via the harmonic balancer. It mounts off the engine block and reads the front crank pulley to tell the engine what position the engine internals are in. This sensor is crucial for starting the car as the ECU will not allow the engine to start without this signal.

Show More Show Less

Genuine BMW Cylinder Head Bolts - Set - N54

T#:22183

Part#: 11127574303

In Stock

7% off MSRP $ 125.65

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 116.62 USD

Add to Wish List

Qty

7% off MSRP

$ 125.65

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 116.62 USD

Add to Wish List

Genuine BMW Set Bolt Cylinder Head - Torx
This item fits the following BMW Chassis:
E82 1M Coupe,E71 X6,E82,E89 Z4,E90,E92,E93,F01,F02

Fits BMW Engines including:
N51,N54,N54T

Show More Show Less

Genuine BMW Single Piston Ring Set - E9X M3, E6X M5 M6

T#:33569

Part#: 11257840940

Ships in 8 Business Days

2% off MSRP $ 327.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 321.99 USD

Add to Wish List

Qty

2% off MSRP

$ 327.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 321.99 USD

Add to Wish List

A piston ring is a split ring that fits into a groove on the outer diameter of a piston. The three main functions of piston rings in reciprocating engines are, sealing the combustion/expansion chamber, supporting heat transfer from the piston to the cylinder wall and regulating engine oil consumption.

Show More Show Less

Piston Ring Repair Kit

T#:33521

Part#: 11257559434

In Stock

Sale - Save 5% $ 120.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 114.47 USD

Add to Wish List

Qty

Sale - Save 5%

$ 120.99

This product was last offered at the strikethrough price on
06-25-2026

$ 114.47 USD

Add to Wish List

Genuine BMW Repair Kit Piston Rings - (0)
This item fits the following BMW Chassis:
E70 X5,E82,E83 X3,E85,E86,E89 Z4,E90,E92,E93,F10,F25 X3

Fits BMW Engines including:
N51,N52,N52N

Show More Show Less

Genuine BMW Repair Kit Piston Rings - 11257610297

T#:33540

Part#: 11257610297

Ships in 3 Business Days

5% off MSRP $ 127.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 121.99 USD

Add to Wish List

Qty

5% off MSRP

$ 127.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 121.99 USD

Add to Wish List

Genuine BMW Repair Kit Piston Rings - (0)
This item fits the following BMW Chassis:
E82 1M Coupe,E71 X6,E82,E89 Z4,E90,E92,E93,F01,F02,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4 X4,F30,F32,F33,F34,F36

Fits BMW Engines including:
N54,N54T,N55

Show More Show Less

Genuine BMW Crankshaft hub - N54 3.0L

FOr vehicles with production from 03/2009

T#:32910

Part#: 11237593701

In Stock

5% off MSRP $ 109.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 103.99 USD

Add to Wish List

Qty

5% off MSRP

$ 109.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 103.99 USD

Add to Wish List

Genuine BMW Hub
This item fits the following BMW Chassis:
E82 1M Coupe,E71 X6,E82,E89 Z4,E90,E92,E93,F01,F02

Fits BMW Engines including:
N54,N54T

Show More Show Less

Genuine BMW Cam Bearing Ledge - Exhaust - N52 N54 N55 3.0L

T#:31384

Part#: 11127531224

In Stock

17% off MSRP $ 706.36

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 586.49 USD

Add to Wish List

Qty

17% off MSRP

$ 706.36

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 586.49 USD

Add to Wish List

Genuine BMW Bearing Ledge Exhaust

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

This item fits the following BMW Chassis:
E82 1M Coupe,E70 X5 X5,E71 X6,E82,E83 X3,E85 Z4,E86 Z4,E89 Z4,E90,E92,E93,F01,F02,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4 X4,F30,F32,F33,F34,F36,F80 M3,F82 M4,F83

Fits BMW Engines including:
N51,N52,N52N,N54,N54T,N55,S55

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Genuine BMW Intake Bearing Ledge - N54 3.0L

T#:31411

Part#: 11127550913

In Stock

5% off MSRP $ 706.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 674.99 USD

Add to Wish List

Qty

5% off MSRP

$ 706.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 674.99 USD

Add to Wish List

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.
Genuine BMW Bearing Ledge Intake
This item fits the following BMW Chassis:
E82 1M Coupe,E71 X6,E82,E89 Z4,E90,E92,E93,F01,F02

Fits BMW Engines including:
N54,N54T

Show More Show Less

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

T#:18733527

Part#: VTT-CRANKHUB-2

Ships in 10 Business Days

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Genuine BMW Set Bolt Cylinder Head - N55

T#:22172

Part#: 11122165470

Ships in 1-2 days

6% off MSRP $ 125.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 118.00 USD

Add to Wish List

Qty

6% off MSRP

$ 125.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 118.00 USD

Add to Wish List

Genuine BMW Set Bolt Cylinder Head - Torx
This item fits the following BMW Chassis:
E71,E82,E90,E92,E93,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F32,F33,F34,F36

Fits BMW Engines including:
N55

Show More Show Less

Genuine BMW Adjustment Unit - outlet Camshaft

T#:34660

Part#: 11367583208

Ships in 3 Business Days

3% off MSRP $ 674.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 657.99 USD

Add to Wish List

Qty

3% off MSRP

$ 674.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 657.99 USD

Add to Wish List

Genuine BMW Adjustment Unit, Outlet Camshaft -
This item fits the following BMW Chassis:
E70 X5,E71,E82,E83 X3,E85,E86,E89 Z4,E90,E92,E93,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F32,F33,F34,F36,F80 M3,F82 M4,F83

Fits BMW Engines including:
N51,N52,N52N,N55,S55

Show More Show Less

Genuine BMW Camshaft - Intake - E60 E61 E82 E88 E90 E91 E92 E93 F10 Z...

T#:34049

Part#: 11317563663

Ships in 3 Business Days

3% off MSRP $ 1,116.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,088.99 USD

Add to Wish List

Qty

3% off MSRP

$ 1,116.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,088.99 USD

Add to Wish List

Genuine BMW Inlet Camshaft -
This item fits the following BMW Chassis:
E70 X5,E82,E83 X3,E85,E86,E89 Z4,E90,E92,E93,F10,F25 X3

Fits BMW Engines including:
N51,N52,N52N

Show More Show Less

Genuine BMW Eccentric Shaft - BMW N55 S55 3.0L

T#:34783

Part#: 11377589883

Ships in 1-2 days

8% off MSRP $ 1,141.87

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,049.83 USD

Add to Wish List

Qty

8% off MSRP

$ 1,141.87

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,049.83 USD

Add to Wish List

The eccentric shaft is an important component of BMW's Valvetronic system, a form of variable valve lift control. If the teeth on the gear or the lobes have worn out, this can result in improper valve lift, decreased or abnormal performance, and even damage to cylinder head components.

Show More Show Less

BE Bearings Performance Rod Bearing Replacement "Dry" Kit - E9x M3 W/...

T#:9868817

Part#: 11247838088DR2KT

In Stock

$ 974.33

This product was last offered at the strikethrough price on
07-21-2026

$ 973.82 USD

Add to Wish List

Qty

$ 973.82 USD

Add to Wish List

NOTE: This is a Dry kit and does not include engine oil. See our catalog for all engine oil options! Includes everything needed for a rod bearing service, featuring BE Bearings upgraded rod bearings. The S65 engine has a known history of rod bearing failure, and if your engine is higher mileage, don't let this catastrophic failure happen to you. Replace your rod bearings and prevent a spun bearing which can trash your crankshaft. BE Bearings, in conjunction with Clevite, an OE bearing manufacturer, have redesigned and manufactured the bearings for greater clearance and have changed the original material composition from tin-aluminum to lead-copper. This upgrade incorporated the state-of-the-art Clevite Tri-Metal design and featured a Tri-Armor™ coating. This allows for the additional lubrication for wear prevention, plus, the softer bearings are better for your engine and are more tolerant of foreign particles suspended in your oil. Another benefit from this is that the oil can now be sent for testing to accurately gauge the amount of wear occurring in the engine. Kit includes Upper and lower BE Bearings upgraded rod bearings Hardware Oil filter Oil pan gasket RedLine assembly lube

Show More Show Less

N55 Turbo Install Kit

T#:401612

Part#: 18407502196KT2

In Stock

$ 290.99 USD

Add to Wish List

Qty

$ 290.99 USD

Add to Wish List

Cam Bearing Ledge Replacement Kit - N54

T#:640352

Part#: 11127531224KT2

In Stock

$ 1,641.21 USD

Add to Wish List

Qty

$ 1,641.21 USD

Add to Wish List

Over time the bearing ledges in your N54 can be damaged by contaminated oil or a malfunctioning VANOS which can cause grooves to form in the bearing ledges. This kit contains everything necessary to replace these as well as important hardware.

Show More Show Less

E9X S65 WPC Performance Rod Bearing Replacement Kit

T#:7260312

Part#: S65WPCDKT

In Stock

Sale - Save 2% $ 1,394.99

This product was last offered at the strikethrough price on
05-03-2026

$ 1,370.29 USD

Add to Wish List

Qty

Sale - Save 2%

$ 1,394.99

This product was last offered at the strikethrough price on
05-03-2026

$ 1,370.29 USD

Add to Wish List

Spline Lock Crank Hub Solution W/ Hardware Package - N54

T#:18733526

Part#: VTT-CRANKHUB-4

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - N54

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Spline Lock Crank Hub Solution

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

VTT N54 “Spline Lock” CrankHub Solution Package W/ Crank Bolt Cap...

T#:19395579

Part#: VTTCRANKHUBPKG

Ships in 10 Business Days

$ 934.99 USD

Add to Wish List

Qty

$ 934.99 USD

Add to Wish List

VTT is proud to offer the only complete N54 complete crank hub solution that does NOT require the crank to be drilled for pins. Our hub uses our proprietary “Spline Lock” technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). We spent many months testing, and retesting this design, utilizing well over 10 different samples to come to our final production version. During testing, our final hub managed to break our testing rig before slipping. These have been bench tested, and real-world tested on the VTT N54 race car spinning 8K RPM and making well over 900WHP. This technology means our hub installs the same as a stock hub, no drilling of the crank, which means MUCH less labor is involved and is reversible is ever wanting to be uninstalled leaving no holes in the crank. The “Spline Lock” is ONLY available with the VTT Crank bolt capture for the ULTIMATE Crank Hub solution for your BMW. These parts are designed to be used together, and the spline lock should not run without the CBC VTT “Spline Lock” Crank hubs are CNC manufactured from 440C tool Steel with a Rockwell rating of HRC60 for the ultimate in durability, and toughness. Hub Plus OEM bolt OEM Oil pump sprocket OEM oil sprocket retainer VTT Crank bolt capture

Show More Show Less

Genuine BMW Cam Gear - Exhaust

T#:34646

Part#: 11367540348

Ships in 3 Business Days

3% off MSRP $ 674.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 657.99 USD

Add to Wish List

Qty

3% off MSRP

$ 674.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 657.99 USD

Add to Wish List

Genuine BMW Adjustment Unit, Outlet Camshaft
This item fits the following BMW Chassis:
E82 1M Coupe,E71 X6,E82,E89 Z4,E90,E92,E93,F01,F02

Fits BMW Engines including:
N54,N54T

Show More Show Less

Genuine BMW Cam Gear - Intake

T#:34645

Part#: 11367540347

Ships in 1-2 days

3% off MSRP $ 674.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 657.99 USD

Add to Wish List

Qty

3% off MSRP

$ 674.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 657.99 USD

Add to Wish List

Genuine BMW Adjustment Unit, Inlet Camshaft
This item fits the following BMW Chassis:
E82 1M Coupe,E71 X6,E82,E89 Z4,E90,E92,E93,F01,F02

Fits BMW Engines including:
N54,N54T

Show More Show Less

S65 WPC Performance Rod Bearing Replacement Kit

Stronger & smoother, with less friction!

T#:5498491

Part#: S65WPCKT

In Stock

Sale - Save 1% $ 1,583.99

This product was last offered at the strikethrough price on
05-03-2026

$ 1,561.76 USD

Add to Wish List

Qty

Sale - Save 1%

$ 1,583.99

This product was last offered at the strikethrough price on
05-03-2026

$ 1,561.76 USD

Add to Wish List

The S65 engine has a known history of rod bearing failure, and if your engine is higher mileage, don't let this catastrophic failure happen to you. Replace your rod bearings and prevent a spun bearing which can trash your crankshaft. What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both. What are you waiting for? Use WPC-treated bearings on your next engine build or rod bearing service! Kit includes Upper and lower WPC Treated Genuine BMW Rod Bearings Hardware Oil filter Castrol TWS Edge Professional Oil pan gasket RedLine assembly lube

Show More Show Less

Genuine BMW Camshaft Exhaust - 11317563665

T#:34051

Part#: 11317563665

Ships in 3 Business Days

3% off MSRP $ 1,116.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,088.99 USD

Add to Wish List

Qty

3% off MSRP

$ 1,116.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,088.99 USD

Add to Wish List

Genuine BMW Camshaft Exhaust -
This item fits the following BMW Chassis:
E70 X5,E82,E83 X3,E85,E86,E89 Z4,E90,E92,E93,F10,F25 X3

Fits BMW Engines including:
N51,N52,N52N

Show More Show Less

E9X M3 Rod Bearing Set

T#:340427

Part#: TMS222796

In Stock

Starting at $ 847.99 USD

Add to Wish List

Starting at $ 847.99 USD

Add to Wish List

Rod bearings should be replaced as a preventative measure before 80,000 miles. This is the set of rod bearings for the S65 V8 in the E90/E92 M3 (BMW part numbers 11247841703 and 11247841702). This is just the set of bearings and does not include any of the other items that need to be replaced at the same time (connecting rod bolts, oil pan gasket, hardware, etc).

Show More Show Less

Rocker Arm - Engine

T#:34795

Part#: 11377628306

Ships in 3 Business Days

6% off MSRP $ 99.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 93.99 USD

Add to Wish List

Qty

6% off MSRP

$ 99.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 93.99 USD

Add to Wish List

Genuine BMW Intermediate Lever - "3"
This item fits the following BMW Chassis:
E70 X5,E71,E82,E83 X3,E85,E86,E89 Z4,E90,E92,E93,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F31,F32,F33,F34,F36

Fits BMW Engines including:
N20,N26,N51,N51,N52,N52N,N55

Show More Show Less

Genuine BMW Crank Pulley With Harmonic Balancer - E82 E84 E88 E90 E92...

T#:32908

Part#: 11237576675

Ships in 3 Business Days

8% off MSRP $ 789.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 723.99 USD

Add to Wish List

Qty

8% off MSRP

$ 789.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 723.99 USD

Add to Wish List

The vibration damper, sometimes referred to as the crankshaft pulley, is a crucial part of the engine in your BMW. Not only does this pulley supply power to all of the belt-driven accessories on the engine, it also absorbs the shock of the engine while it is running to help give your engine a smooth, quiet idle. If you vibration damper is failing, it will usually present itself in the form of a squealing noise that sounds like a slipping belt. This is an indication that the rubber ring inside of the vibration damper has dried out and cracked, causing the pulley to slip. If your vibration damper has seen better days, it must be replaced in order to keep your engine running properly, and all of you accessories functional.

Show More Show Less

Genuine BMW Connecting Rod - Set of 6 - N55 S55

T#:33055

Part#: 11247624615

Ships in 3 Business Days

4% off MSRP $ 1,247.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,191.99 USD

Add to Wish List

Qty

4% off MSRP

$ 1,247.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,191.99 USD

Add to Wish List

Genuine BMW Set Connecting Rod -
This item fits the following BMW Chassis:
E71,E82,E90,E92,E93,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F32,F33,F34,F36

Fits BMW Engines including:
N55, S55

Show More Show Less

N54 Crank Hub Service Kit - Up To 02/2011

For vehicles with production date up to 02/2011

T#:2227021

Part#: N54PRCRANKT

In Stock

Sale - Save 4% $ 156.99

This product was last offered at the strikethrough price on
05-03-2026

$ 151.49 USD

Add to Wish List

Qty

Sale - Save 4%

$ 156.99

This product was last offered at the strikethrough price on
05-03-2026

$ 151.49 USD

Add to Wish List

All of the components necessary for service when upgrading to an aftermarket crank hub solution.

Genuine BMW Connecting Rod Set - N54 3.0L

T#:33045

Part#: 11247586491

Ships in 9 Business Days

4% off MSRP $ 1,247.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,191.99 USD

Add to Wish List

Qty

4% off MSRP

$ 1,247.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,191.99 USD

Add to Wish List

Genuine BMW Set Connecting Rod
This item fits the following BMW Chassis:
E82 1M Coupe,E71 X6,E82,E89 Z4,E90,E92,E93,F01,F02

Fits BMW Engines including:
N54,N54T

Show More Show Less

N54 Spline Lock Crank Hub Solution With Complete Package

T#:18733525

Part#: VTT-CRANKHUB-3

Ships in 8 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Genuine BMW Camshaft Exhaust Zyl.1-4 - 11317841166 - E90,E92,E93 ...

T#:34137

Part#: 11317841166

Ships in 8 Business Days

2% off MSRP $ 1,387.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,353.99 USD

Add to Wish List

Qty

2% off MSRP

$ 1,387.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,353.99 USD

Add to Wish List

The BMW S65 replacement camshaft is a premium OEM-spec component designed to restore or enhance engine performance. Crafted for precise timing and durability, it optimizes valve operation for improved power delivery and efficiency. Perfect for BMW M3 E90, E92, and E93 models, this camshaft ensures factory reliability while supporting high-revving performance. Genuine BMW Camshaft Exhaust - Zyl.1-4 This item fits the following BMW Chassis: E90,E92,E93 Fits BMW Engines including: S65

Show More Show Less

Genuine BMW Piston

T#:186517

Part#: 11258619196

Ships in 3 Business Days

4% off MSRP $ 403.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 385.99 USD

Add to Wish List

Qty

4% off MSRP

$ 403.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 385.99 USD

Add to Wish List

Genuine BMW Piston - (0)
This item fits the following BMW Chassis:
E71,E82,E90,E92,E93,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F32,F33,F34,F36

Fits BMW Engines including:
N55

Show More Show Less

Genuine BMW Eccentric Shaft - 11377515868

T#:34752

Part#: 11377515868

Ships in 3 Business Days

2% off MSRP $ 1,141.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,113.99 USD

Add to Wish List

Qty

2% off MSRP

$ 1,141.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 1,113.99 USD

Add to Wish List

Genuine BMW Eccentric Shaft -
This item fits the following BMW Chassis:
E70 X5,E82,E83 X3,E85,E86,E89 Z4,E90,E92,E93,F10,F25 X3

Fits BMW Engines including:
N51,N52,N52N

Show More Show Less

Rocker Arm - Engine

T#:34794

Part#: 11377628305

Ships in 3 Business Days

6% off MSRP $ 99.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 93.99 USD

Add to Wish List

Qty

6% off MSRP

$ 99.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 93.99 USD

Add to Wish List

Genuine BMW Intermediate Lever - "2"
This item fits the following BMW Chassis:
E70 X5,E71,E82,E83 X3,E85,E86,E89 Z4,E90,E92,E93,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F31,F32,F33,F34,F36

Fits BMW Engines including:
N20,N26,N51,N51,N52,N52N,N55

Show More Show Less

N54 Crank Hub Service Kit - From 02/2011

For vehicles with production date from 02/2011

T#:2227020

Part#: N54POCRANKT

In Stock

Sale - Save 3% $ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 146.41 USD

Add to Wish List

Qty

Sale - Save 3%

$ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 146.41 USD

Add to Wish List

All of the components necessary for service when upgrading to an aftermarket crank hub solution.

Genuine BMW Connecting Rod - E9X M3, E6X M5 M6

T#:33082

Part#: 11247838623

Ships in 5 Business Days

5% off MSRP $ 349.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 333.99 USD

Add to Wish List

Qty

5% off MSRP

$ 349.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 333.99 USD

Add to Wish List

This is a direct replacement connecting rod. This rod has been manufactured to BMW specs. Connecting rods connect the pistons to the crankshaft. This is a Genuine BMW connecting rod for the S65 and S85 engines.

Show More Show Less

Bearing Shell - Red

T#:32584

Part#: 11217515383

Ships in 9 Business Days

6% off MSRP $ 79.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 74.99 USD

Add to Wish List

Qty

6% off MSRP

$ 79.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 74.99 USD

Add to Wish List

Genuine BMW Bearing Shell, Red - 64,50Mm(+0,50)
This item fits the following BMW Chassis:
E82 1M Coupe,E70 X5,E71 X6,E82,E83 X3,E85 Z4,E86 Z4,E89 Z4,E90,E92,E93,F01,F02,F06,F10,F12,F13,F15,F16,F22,F25 X3,F30,F32,F33,F34

Fits BMW Engines including:
N51,N51,N52,N52N,N54,N54T,N55

Show More Show Less

Genuine BMW Repair Kit Piston Rings (0) - 11257570405 - E90,E92,E93 ...

T#:33529

Part#: 11257570405

Ships in 8 Business Days

5% off MSRP $ 127.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 121.99 USD

Add to Wish List

Qty

5% off MSRP

$ 127.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 121.99 USD

Add to Wish List

Genuine BMW Repair Kit Piston Rings - (0)
This item fits the following BMW Chassis:
E90,E92,E93

Fits BMW Engines including:
N54

Project Cars

SELECT YOUR BMW

BMW Internal Engine Parts for BMW 3 Series E92 (2007-2013)

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results