BMW Suspension Parts for BMW 3 Series E92 (2007-2013)

Maintaining optimal vehicle alignment is crucial, especially when dealing with challenging road or track conditions. To prevent excess tire wear and ensure precise vehicle handling, turn to the Godspeed Project Rear Toe Arms.

These rear toe arms offer stability at high speeds, thanks to their precise alignment capabilities. Unlike traditional rubber bushings that wear quickly, these arms feature solid spherical bushings for exceptional durability. Their heat-treated ball and hard chrome-plated alloy steel composition guarantee strength and longevity.

Not only do these rear toe arms provide cost-effective performance improvements, but they also offer extended adjustment ranges and versatility. Their solid design enhances road feel, giving you more control and confidence in your BMW's performance.

Please note that realignment is recommended after installation, and these rear toe arms are intended for "Track Use Only" due to the increased road noise and vibration caused by solid bushings.

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

• 100% machined and anodized, 6061-T6 lightweight aluminum arms
• High-strength, 3-piece, rod end (with carbon fiber reinforced, PTFE race) offers longer life for street compared to standard rod ends
• SEALS-IT Rod end seals keep dirt, water, and other contaminants out
• Rod ends feature grease fittings, to allow for rod end serviceability.
• Lighter than stock!  (Stock is 875g, RE arms are 640g)
• Extremely easy installation and adjustment (your alignment shop will LOVE you!)

The camber plates improve on the amount of adjustment and fine-tuning available in the front suspension to improve mechanical grip while cornering. Made to the same quality you'd expect from Dinan and BMW, they help to fine-tune the right amount of camber for Dinan springs.

• Improved mechanical grip
• Reduced understeer
• Works great with Dinan springs
• Worth 1 point toward your Dinan badge

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere.

This item fits the following BMWs: 

2008-2013 BMW M3 

Dinan Performance Springs are matched to your BMW's chassis and suspension components to deliver better handling and looks without sacrificing ride quality. Dinan BMW springs are carefully engineered to work within your car's suspension travel and to improve suspension geometry. Spring rates are slightly stiffer than stock and dialed in to reduce bodyroll. A stiffer suspension makes the car more fun to drive and the lower ride height improves the looks by reducing wheel-fender gap.

Dinan spring specs -

• F: -1/2" (12mm)
  
• R: 0" (0mm)

Fitment note: When used with stock shocks the Dinan Ride Quality Kit is strongly recommended. The Kit consists of shorter and stiffer bump stops and spring perches that work better with the lowered ride height of these springs. While not explicitly required, less than favorable ride quality and handling may result without them.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. The springs are worth 2 points towards your Dinan badge (Ride Quality Kit is worth 1 point).

This item fits the following BMWs:
2007-2013 E92 BMW 335i 335is 335xi - Coupe

Dinan sway bars are carefully engineered to match the driving dynamics of each BMW chassis. Dinan's research and development finds the ideal balance between improved handling while maintaining a comfortable ride. This set has been fine-tuned for the E90/E92 chassis to reduce bodyroll, improve steering and turn-in response, and reduce understeer. The front bar is hollow tubular steel for light weight with adjustable ends to dial in the handling characteristics. The rear bar is non-adjustable. These are the same sway bars used in Dinan's Stage 1 suspension and work best with Dinan shocks and springs or a similar sport suspension and wider rear tires.

Dinan E9X Sway Bar Specs:
F: 28mm, hollow, 2-position adjustable, adjustable links, urethane bushings, and brackets included
R: 15.8mm, solid, non-adjustable, urethane bushings included

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. Each sway bar is worth 1 point towards your Dinan badge.

Note: main image may not match actual sway bars.

This item fits the following BMWs:
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2007-2011 E91 BMW 325i 328i - Touring Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible

Rogue Engineering E82/E9X Adjustable Rear Camber Link Set V2.0 is the ultimate upgrade for BMW enthusiasts seeking enhanced handling, improved tire wear, and precise suspension tuning. This high-performance solution is engineered to fit BMW E82 1-Series and E9X 3-Series models, offering superior adjustability and durability over OEM components. Ideal for street and track use, this camber link set is crafted from premium materials to ensure strength and long-lasting performance.

Key Features:

These replace the wishbone and guide arm links in the factory suspension which have rubber bushings and limited adjustment. Enhanced suspension adjustability for optimized alignment Improves handling and reduces uneven tire wear Compatible with BMW E82 1-Series and E9X 3-Series models Constructed from high-strength materials for durability and reliability Perfect for both street performance and track applications Turner Motorsport proudly offers the Rogue Engineering E82/E9X Adjustable Rear Camber Link Set V2.0, providing BMW drivers with unmatched performance and precision.