The intake boot is a regular issue especially for BMW's, nearly all vehicles have a boot manufactured from rubber with an accordion section in the design for flexibility. This flexible section is typically where the failure comes from leading to vacuum leak engine codes, rough idle, and increase fuel consumption. 

When you upgrade to a Turner silicone intake boot you get a perfect fit that will not only outlast the OE design (meaning any vacuum leaks and rough idle), while also smoothing out airflow within the intake tract. This boot also eliminates the factory intake resonator giving your engine a much more aggressive sound under the hood especially at higher rpm. Available in black or Turner blue color, our intake boot offers either a pop of color or a cohesive, complementary look in your engine bay.

The Turner Motorsport silicone intake boot is manufactured with 5 layers of wire reinforced silicone to prevent collapse under load. Engineered in-house utilizing 3D scanning technology, this boot offers perfect fitment with the factory air box and either single stage or three stage (high output N52) intake manifolds.

Install as a standalone reliability improvement or in addition to our three stage intake manifold and Turner performance tune (available here).

Replaces OE intake boot 13717536004.

Features:

• 5 layers of wire reinforced silicone
• Perfect fitment with factory airbox
• Compatible with single stage or three stage manifold
• Installation hardware included

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i Coupe Convertible
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi - Coupe
2007-2013 E93 BMW 328i - Convertible

Full carbon fiber intake to increase flow, performance and aesthetics! Dual inlet design for maximized air flow while retaining the OEM+ fitment.

The most common N55 intake utilizes a short plastic tube and oversized cone filter; it is your job to have better taste than the common N55 owner. This carbon intake changes the whole image of the N55 engine while maintaining a flow of cool air and added induction noise. With a dual inlet design the engine bay retains its functionality while adding a second inlet to provide your engine with improved air flow and sound. To ensure the engine gets the coolest air possible the second inlet is located in the "sweet spot" on the cold side of the engine for the lowest intake air temps and most air flow possible. The cone filter features a bellmouth velocity stack filter that creates the satisfying flutter after letting of the throttle.

Our Turner Carbon Fiber Intakes start with a 3D scan of the factory intake and engine bay. Engineers use the 3D imaging of the chassis to design the intake in SolidWorks modeling software. Using a Flow Bench, the Intake is then airflow tested against the factory intake, to ensure optimal airflow improvement against stock. The final product is a beautiful and functional Carbon Fiber Intake, CAD designed for perfect integration with the OEM inlet ducting and stock mounting locations and proven to flow better than factory.

Key Benefits:

Increased flow over the factory intake
Carbon fiber airbox and intake tube with gloss clear coat for UV protection
CAD-Designed for perfect Integration
Custom high flow air filter specially designed to to pair with the carbon fiber airbox
Kit Contents:

Carbon Intake Tube
Full Carbon 2 Piece Airbox
Bellmouth Velocity Stack Cone Filter
Billet Turbo Inlet Adapter
Silicone Coupler
Hardware For Installation
Design:

- Carbon Fiber Intake Tube

Carbon inlet tube featuring a smoother interior without corrugations for a smooth flow path.
Integrated carbon flange allows secure mounting of the tube to the carbon air boxes.
Intake tube is manufactured using 2x2 twill weave carbon fiber for a great look in the engine bay.
Gloss finish clear coat for UV protection.
4-ply reinforced silicone coupler and 6061-T6 black anodized aluminum flange that utilizes the factory o-ring and retaining clip.
- Air Box

Carbon fiber airboxes are manufactured using 2X2 twill weave carbon fiber and protected with a gloss finish clear coat for UV resistance to match the intake tube.
Air box mounts in stock location with supplied hardware.
- Air Filter

Conical hi-flow reusable air filter; featuring 8 ply oiled cotton gauze construction to maximize filtration efficiency.
Bellmouth (velocity stack) filter flange inlet to reduce turbulence in order to maximize flow.
Product Development:

Turner N55 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.

Fitment:

E82 135i N55
E88 135i N55
E84 X1 35i
E90 335/xi N55
E92 335/xi N55
E93 335/xi N55

Replacement N55 Performance Filter from Burger Motorsport

Enhance your BMW's performance with the Replacement N55 Performance Filter from Burger Motorsport. Specifically designed for N55 engines, this filter optimizes airflow, leading to increased horsepower and torque. Enjoy improved throttle response and fuel efficiency, all while protecting your engine from harmful contaminants.

Key Features:

• Designed for N55 engines
• Optimizes airflow for increased power
• Improves throttle response and fuel efficiency
• Protects engine from contaminants

In BMW's with the N55, the intake system is partially limited. The bottom portion is lightweight and great for feeding cold air to the intake, but the top portion is excessively restrictive. Working with some of the original equipment, this intake continues to utilize the bottom portion of OE ducting and heat shielding, but replaces the top with new high flow ducting and a performance filter. Extensive testing showed up to a 10+ HP gain to the wheels and allows for quicker turbo spool speed. Plus, this design gives you a great sound improvement, letting you hear both the intake and turbo spooling!

Installation and removal is extremely quick and easy, taking only 5 minutes in the driveway!

Features:

• Adds up to 10+ Horsepower
• Dramatic sound improvement
• Super fast install and removal
• Improves throttle response 
• Retains OEM airbox base as a heat shield
• Retains OEM cold air ducting
• Looks great under the hood
• Cleanable and reusable filter
• Made in the USA

An easy way to improve the performance of your N54 powered BMW is by removing the stock air box and swapping in this Dual Cone Intake "DCI" from Burger Motorsports. Featuring two S&B inverted cone filters with adapter couplers and new hardware, these easily install into the stock box location, allowing for greatly improved intake air flow. This is great for both stock and modified vehicles, as this allows for greater air flow at all RPMs and removes the air restriction that would normally rob your engine of power.

In addition to increased power, these filters give your engine a more aggressive appearance and sound that any automotive enthusiast will appreciate.

MADE IN THE USA

**CARB Approved Under Executive Order (EO) No. D-744-2 for all 2007-2012 BMW models equipped with the N54 3.0L twin-turbocharged 6-cylinder engine.**

Unlock the full potential of your turbocharged N54 or N55 engine with the Turner Motorsport Stepped Intercooler. Whether you're running higher boost, track days, or just spirited street driving, this direct-fit upgrade is engineered to dramatically reduce intake air temperatures (IATs) and improve charge air flow for consistent, reliable performance.

Cooler air is denser air, and that means more oxygen per cycle for better combustion and more power. The factory intercooler quickly becomes a bottleneck under increased load or in warm conditions. Turner’s stepped intercooler solves that by offering an 80% increase in frontal surface area and cross-sectional flow, helping your BMW stay cooler and pull harder.

Constructed with high-quality cast aluminum end tanks and a bar-and-plate core, this intercooler delivers superior cooling efficiency and reduced pressure drop, even under sustained high-boost operation. The black powder-coated finish offers a clean, stealthy appearance, while the etched Turner logos add just the right touch of motorsport style.

Perfect for:
E82/E88 135i, E9X 335i/335xi, E84 X135i, E89 Z4 35i/35is

Key Features:

Direct-fit upgrade for E chassis N54 & N55 engines
Durable cast aluminum end tanks
High-efficiency bar-and-plate design
80% increase in frontal and cross-sectional area vs. stock
90% increase in charge air volume
Substantially lower IATs for improved power and reliability
Reduced and more consistent pressure drop
Lightweight design (under 20 lbs)
Dimensions: 520mm wide × 210mm tall × 130mm deep
Stealth black finish with Turner-etched logos
If you're looking to push your turbo BMW harder, the Turner Motorsport Stepped Intercooler is the cooling solution that keeps your engine running strong—pull after pull.

Upgrade your BMW's performance with the BMS N54 BOV Vacuum Adapter, a plug-and-play solution that enhances engine vacuum functionality. Easily attachable to the throttle body/brake booster vacuum line, this adapter provides two extra 1/8" NPT vacuum ports, offering versatile applications like replacing vacuum lines to diverter valves, connecting boost gauges, and more.

• Quick and hassle-free installation
• Two additional 1/8" NPT vacuum ports for multiple applications
• Ideal for replacing engine vacuum lines to diverter valves
• Enables a larger diameter boost reference to aftermarket BOV
• Perfect for adding extra boost gauges and accessories
• CNC machined for precise fit and durability
• Dual internal O-rings and retaining clip for a secure, factory-like seal
• Basic kit includes adapter, two 1/8" NPT caps, and one 1/8" vacuum nipple
• BOV kit adds two push lock fittings and 1/4" line for Tial BOV installation
• Made in the USA for quality assurance

Enhance your BMW's performance and functionality with the BMS N54 BOV Vacuum Adapter – a versatile, plug-and-play solution made in the USA.

In addition to the weak stock chargepipe, the factory N54 diverter valves can also be a source for boost leaks. The diverter valve takes overboost and re-directs it back through the intake and turbos instead of allowing it to pass into the intake manifold. It's the same as a blow off valve (BOV) but instead of releasing into the engine bay, it stays contained to the engine. The stock diverter valves (DV) are plastic and connect with more plastic into the chargepipe and turbo inlet pipes. The plastic can become brittle and crack even on stock engines and leak boost, which leads to a loss in power and performance.

Turbosmart has developed two kits to replace and upgrade the stock diverter valves - a direct replacement kit and a combination DV/BOV "Dual Port" kit (shown). This Dual Port Kit is a DV and a BOV together in one unit. An internal valve directs some of the charged air into the turbo inlets and the rest is dumped into the engine bay like a traditional BOV. The amount of boost released into the air is determined by an internal spring in the Dual Port unit (additional springs are also available). This allows you to custom tailor how much boost and BOV "whoosh" you hear. In addition to the DV/BOV combo, stronger silicone hose is included to connect them to the turbo inlet pipes (Vargas silicone inlets are recommended). The Turbosmart Kompact Dual Port will give you all of the strength and reliability you need to take your turbo build to the next level.

You will also need T#553932