Turner Motorsport for BMW 3 Series E92 (2007-2013)

The E46 M3 CSL sparked a lot of interest among enthusiasts about the "high kick" look. But what about those who want the aggressive, high kick look without having to replace the entire trunk? We took it upon ourselves to CAD design an aggressive, high kick spoiler that pays homage to the CSL styling, while flowing perfectly with the beautiful body lines of the E92 that resonate with BMW enthusiasts everywhere. Our carbon fiber is hand laid, with a beautiful gloss finish that will match well with any other carbon fiber accents on your E92 coupe. Our high kick rear spoiler will instantly give your vehicle a more aggressive look.

Installation is very simple. First, clean your trunk lid, then remove the backing on the already attached double sided tape and press firmly to apply the spoiler. We recommend installing in a warm environment to ensure long-lasting application.

Features:

No drill installation Pre-installed high strength double sided tape Hand laid carbon fiber with gloss finish This product fits the following BMWs:

2007 - 2013 E92 328i 328xi 335i 335xi M3

At Turner, all our Carbon Fiber Intake Systems are top-of-the-line custom-engineered products that we develop in house. Our Turner S65 Carbon Intake is a monster that perfectly compliments the high revving 4.0l V8 engine. Add in a full carbon plenum and you have a recipe for greatness! The intake benefits start right at the motor; the plenum offers a larger interior volume and full carbon design which helps boast the intoxicating roar. Directly connected to the plenum is a full carbon intake tube with a substantially larger cross sectional area with smooth transitions which results in more airflow available to the engine in high demand scenarios. The inlet tube mounts securely to the full carbon heat shield and is mounted in factory airbox locations while retaining the factory cold air induction tract from the hood. Housed inside the heat shield is a behemoth cone filter to ensure proper filtration and maximize airflow. Turner's S65 intake and plenum is designed with air flow and induction in mind. The intake flows like no other; during testing, the Turner intake outperformed the flow-bench at over 750CFM, a massive improvement over the factory intake.

Here are the benefits:

Full carbon plenum and intake for a full engine bay transformation
You get a beautiful carbon heatshield, one of the only full carbon fiber heatshields available.
All the flow - the air on demand will make sure your engine always has room to breathe.
Increased throttle response.
Added induction noise for an intoxicating driving experience.
PART DESIGN:

Designed and engineered in-house using state of the art 3D laser scanning and CAD technology for precision fitment
Full Carbon Plenum construction with internal bracing and velocity stacks
Hood Inlet Scoop - Directs the flow of cool, ambient air to the heat shield, and directly into the air filter. Seals off with the factory rubber gasket on the lower side of the hood inlet.
Full Carbon Fiber Heat Shield Assembly that utilizes OEM air box mounts and integrates with the factory air intake tract from the hood.
Monstrous 9" cone air filter to maximizes filtration that is able to be serviced/cleaned.
7"x5" Carbon Fiber Inlet Tube providing smooth, direct airflow from the behemoth air filter directly into the plenum.
Fully compatible with the OEM Secondary Air Injection emissions system. Factory hose lock and location.
Full carbon fiber plenum with bracing and carbon velocity stacks.
KIT CONTENTS

Carbon Fiber Plenum
Carbon Fiber Heat Shield
Carbon Fiber Intake Tube
Plenum Silicone Coupler
9" Cone Air Filter
Installation Hardware
PRODUCT DEVELOPMENT

Turner S65 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

3.0" Inner Diameter
4.0" Outer Diameter
Black Chrome Finish
Double Wall Construction
Slant Cut Style
Includes Stainless Steel Clamp

Rubber engine and transmission mounts for a street car and solid aluminum for the track, right? Well, it's not that straightforward anymore.

Stock rubber fluid-filled mounts are designed to be soft and comfortable, limiting the NVH (noise, vibration, and harshness) felt by the driver. The drawback inherent with a conventional design is driveline deflection, making it more difficult to put the power to the wheels, as well as making a money-shift or miss-shift more likely as they age. Solid mounts are exactly the opposite of this - they permit tons of NVH while offering zero deflection, making these a must have for track-driven vehicles looking to capitalize on every ounce of performance available. Enthusiasts looking to find the best of both worlds often look to polyurethane engine mounts - and many are disappointed with other designs on the market. Seeking a mount that offers a positive connection yet doesn't deform, fail, or rattle the fillings out of their mouths is frequently a lost cause.

Until now. 

We engineered these mounts with these very concerns in mind. We know if a soft mount offers a sloppy connection it doesn't work on the track, and a solid mount isn't acceptable as a daily driver (for most!) and set out to engineer a mount that would meet the needs for both. At the core of our enclosed design is a partially-constrained, multi-piece polyurethane bushing with precisely-set preload. This architecture absorbs and disperses resonant engine frequencies as opposed to amplifying them (like some other designs do), which results in a positive-connection, enthusiast-feel mount with the vibration. Understanding that heat is a concern for the passenger side mount's close proximity to the exhaust, we utilize a PEEK thermal insulation plate to greatly reduce heat transfer to the polyurethane, making heat a non-issue for these mounts. 

We offer two durometers, with both densities offering similar "positive connection" feeling. 60A is slightly softer and offers more of a stock feel, while 80A delivers a little more engine "feel" while under acceleration. 

Product features and benefits:

• Crisper throttle response, positive shifter location, direct power transfer
• High quality polyurethane offered in both 60A & 80A durometers (rebuildable, too)
• Resistant to water, ozone, and chemicals, maintaining its resiliency and elasticity longer than conventional rubber.
• Precision machined billet 6061-T6 aluminum housing, black anodized for durability and corrosion resistance. Grade 10.9 stud - fear not, big turbo owners.
• Thermal isolation spacer on the hot side to resist heat transfer into the poly
• Engineered in-house and made in America

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335d 335i 335xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Turner Motorsport Polo shirts are perfect to show your passion for the race team when you're not in the garage. Pick one up today!

Don't see your size available? Give us a call at 1.800.280.6966 - we have you covered.

By popular demand, our shoe-gripping Turner Motorsport pedal set is now available for E82 1 series and E9X 3 series with automatic transmission. These pedal covers feature pyramid shaped spikes on the brake pedal, which actually BITE the soles of your shoes PERFECTLY, creating the ultimate (and unbeatable) friction surface where you want it. The throttle pedal is left smooth, so that your foot can roll on and off the gas smoothly. The automatic transmission set includes 2 pieces -- one brake pedal and one throttle/gas pedal.

Our pedals are anodized for a beautiful cosmetic finish that resists chips and flaking. Stainless steel hardware is included, as well as a basic installation guide (professional installation always recommended). These pedals are for left-hand drive (LHD), automatic transmission BMWs only (sequential manual transmission cars should use the manual transmission set).

Also available in black anodized! The same shoe-gripping performance as our standard "naked" aluminum racing pedals, but with an added black anodized coating, for a stealth black finish. We always recommend the naked metal pedals for harsher/race type use, as all cosmetic finishes will eventually degrade over time. But for those looking for the black-out look, we can now accommodate! To add this option, simply choose your selection below.