The factory rubber/plastic hoses become brittle and crack over time. Brittle and cracked hoses can cause multiple vacuum leaks that are impossible to repair without hose replacement. Vacuum leaks can cause many problems including rough running, missing, stalling at idle, and even a no-start condition.

The factory hoses offered through BMW are plastic and will yield the same results of becoming brittle and damaged over time. Our solution is a premium replacement that will outlast everyone of the OEM replacements. Our Silicone Crankcase Vent Hose can be used to replace the factory brittle hose to ensure your S54 is free from vacuum leaks and performing properly.

CSL Vent Hose (11157833649) - Silicone Crankcase Vent hose is a direct replacement

Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose that is susceptible to cracking overtime from constant heat cycling

Design:

Retains OEM hose end fittings to ensure proper seal

“Black” 3 ply reinforced silicone w/ “White” Turner logo

All vehicles will lose some degree of performance due to heat soak under the right operating conditions.  Engine management systems constantly monitor operating conditions and modifying parameters based on sensor inputs. BMW integrated the intake air temp sensor in the MAF housing on models such as the E39 M5, and, being sandwiched behind a hot radiator and in some applications next to an even hotter valve cover, this is less than ideal for performance applications. Absorbing excess heat from its surroundings, the MAF can’t shed it fast enough, and the ECU reads an inaccurately high intake air temperature. Compensating for this false hot air measurement, the ECU pulls timing and runs a richer fuel mixture, resulting in a significant loss of torque.

What can you do?  Locate an intake air temp sensor in a location where it can properly measure incoming air temps and where it's less prone to heat soak. Mounting the sensor further away from the heat source and isolating it from the MAF housing, it can both resist the effects of heat soak longer and respond to temperature changes more quickly.  The result is you’ll experience reduced torque loss and more consistent power output when you’re pushing your engine hard. 

The Turner engineering team was initially skeptical of the claimed performance benefits of this modification. They first set out validate the functionality and performance benefit of a temp sensor relocation. Replicating stop-and-go traffic heat soak in a 2001 540i was a simple task in a controlled environment - their dynometer. First the car was heat soaked to simulate being stuck in traffic or moving at low speeds by running the car four times on the dyno with the dyno's cooling fans disabled. The fans were then turned on for three more runs to observe the recovery rate once air flow was reintroduced. The test: following this procedure once with a stock IAT, and once with their relocation kit in place. 

The result? Turner recovered 11lb-ft torque at 2500rpm through use of their relocation kit, with even greater recovery to be found for M5 owners. Here are the heat soak-related torque losses Turner experienced:

Stock IAT location:
18rwtq at 2500rpm
10rwtq at 3000rpm
9rwtq at 3700rpm

Turner IAT Relocation:
7rwtq at 2500rpm
5rwtq at 3000rpm
5rwtq at 3700rpm

**Click here for installation instructions**

The Turner engineering team designed a complete plug and play kit (unlike all other options on the market) that makes for quick, easy, and reversible installation. Weather-sealed connectors keep out the elements, while sheathed wiring offers a clean appearance underhood. With a harness nearly 3 feet long - the Turner IAT relocation kit offers flexibility in positioning, but not too long that you're left with unsightly excess wiring. Turner recommends positioning the sensor in a location away from engine heat, but still within the intake ducting to achieve accurate intake temp readings - such as the far side of the base of the airbox. Vehicles with cold air intakes with cone-style filters can even position the sensor in the end of the filter. Simply drill a hole in your (cool) location of choice and plug in the harness. More information including installation instructions and some good examples of sensor mounting locations can be found in our DIY PDF. 

We include everything you need to relocate your IAT, just select your desired sensor brand below - Genuine BMW or original equipment Beru.

Also the perfect plug-n-play option for anyone looking to upgrade their intake to utilize an Alpha-N tune!

Note for vehicles with M62 engine: applicable to 1999 and up

Upgrade your BMW's performance with Turner Power Pulleys, designed to enhance engine efficiency and increase available horsepower. These pulleys reduce the rotation of essential accessories by up to 10-20%, redirecting engine power to the wheels. Turner ensures these pulleys maintain proper functionality through rigorous on and off-track testing.

Crafted from durable T-6061 aluminum and finished in black hard anodizing, Turner Power Pulleys offer longevity, heat resistance, and chemical durability. They retain the stock-like appearance while providing increased strength and reduced weight, eliminating concerns about plastic failure.

The Turner Motorsport Oil Temperature Sensor Flange was designed to get your oil temperature from the best possible location: the sump. Most of the factory and aftermarket sensors are located after the oil pump, which does not give you an accurate temp reading of the oil that is actually lubricating the engine. At the factory temp sensor location the sensor picks up heat not only from the oil stream, but also from the oil pump and housing which will skew the reading. Other aftermarket adapters can be give inaccurate readings from their location and/or design limitations. And may require making unnecessary modifications. By relocating the sensor to the oil sump it reduces clutter and sits flush against the bottom of the oil pan to avoid potential clearance issues. Testing that we have done on and off the track shows that the sump location is the most accurate. We accomplish this by removing the factory oil level sensor or block off plate and using the existing hole and bolt pattern on the oil pan with no additional modifications. Any sensor with an M12 x 1.50mm thread can be used in the flange. 

Note that removing the factory oil level sensor will trigger the low oil fault/warning light. There's no elegant way around this but since the Temp Flange is considered a race-only part we assume you will be checking your own oil level anyway or be using a stand-alone dash/engine management system that does not track oil level. And having the most accurate oil temp is more important.

Applications:
1987-1991 E30 M3
1992-1999 3 Series E36 M3 3.0 and M3 3.2 Euro Models Only!
1999-2006 3 Series E46 All
1991-1995 5 Series E34 525i M50
1997-2003 5 Series E39 525i, 528i, 530i, 540i, 540iP, M5
2004-xxxx 5 Series E60 525i, 530i
1995-2001 7 Series E38 
Z3 2.5, 2.5i, 2.8, 3.0i, M3.2 S54
Z4 2.5, 3.0
Z8 All

Modern day emissions regulations require the use of a closed crankcase ventilation (PCV) system to recirculate combustion blow-by gases from the crankcase back in to the intake to be burned.  Unfortunately, these blow by gases contain water vapor (which is a byproduct of combustion) and pick up oil mist from and the windage cloud and cam lubrication system as they travel through the crank case.  Due to less than 100% effective air/oil separation in the stock PCV system, some oil mist and water vapor gets carried back to the intake tract and over time cause oil deposits in the intake manifold, intake ports, and on the back of intake valves.  All will eventually lead to poor performance and reduced fuel economy, and the presence of this oil mist in the intake charge may even increase the risk of engine-damaging detonation. 

With forced induction, track use, and/or extended high RPM usage, these symptoms increase as the factory PCV system is overwhelmed, and a catch can becomes a must for your E46 M3. This kit is a direct fit making this an easy reversal if desired as well as maintaining a clean appearance by utilizing the open "smuggler's compartment" on the passenger side of the engine bay.

*Click here for catch can instructions*

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton o-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Valved drainage system - no removal of can necessary to empty

Part of the process of building a proper race car is to delete and simplify portions of the wiring harness. This not only saves weight and reduces complexity, but it also allows you to run a smaller, lighter racing battery. So why is your alternator still charging at the original rate?!? This M50/M52/S52 racing alternator pulley underdrives the alternator more than our standard Power Pulley, freeing up horsepower and reducing alternator wear. This pulley is over 80% larger than the original stock pulley. With less electrical load, you don't need the original alternator output anymore. You can drive the alternator less and return that "lost" horsepower back to the engine. This part is an upgrade to the alternator pulley already included in our Power Pulley kit and was developed and race-proven on our E46 Touring Cars.

Because this pulley is so much larger than the original (80%), special care will need to be taken so that it does not interfere wtih other components on the engine - power steering lines, oil cooler lines, coolant hoses, etc. The upper idler pulley is no longer needed with the racing pulley and will be removed. A new belt is required (add one from the options below).

For Bosch alternators only.

The remainder of the Turner Power Pulley Kit is required (water pump and power steering pump pulleys).

Enhance your BMW's performance with the BMW E46 Z3 Turner Motorsport Power Pulley Kit 325i/330i Valeo Alternator. This high-quality power pulley kit is designed to increase horsepower and torque by reducing parasitic drag on the engine. With easy installation and precise fitment, this kit is a must-have upgrade for any BMW E46 or Z3 owner.

• Increases horsepower and torque
• Reduces parasitic drag on the engine
• Easy installation process
• Precise fitment ensures optimal performance