BMW Engine Parts for BMW 3 Series E46 (1999-2005)

Clear BMW chassis

Please ensure your correct model is selected

Turner Motorsport has everything you need to upgrade your BMW through our stages of performance or to keep your car in peak condition with our range of the latest in proven OEM cooling parts. Upgrade your cooling system and engine performance with the selections below to give your BMW a performance and reliability advantage.

Sub-Categories

Sort By:

Bosch - Corporate Logo
T#:588121
Part#: 12138616153
In Stock
$ 34.99 USD
Free Shipping on orders $49 and up
Sluggish acceleration, misfires, and rusty terminals are symptoms of a worn coil. Located on the top of your engine, these coils should be inspected and replaced as needed or every 100,000 miles. Keep your ignition system in perfect order. Rubber integrated boot and snap-top cap. OEM Bosch Part Number: 0221504800
Show More Show Less
Bosch - Corporate Logo
T#:2021
Part#: 42LBINJ
In Stock
$ 41.99

This product was last offered at the strikethrough price on
11-02-2026

$ 40.05 USD
Free Shipping on orders $49 and up
$ 40.05 USD
Free Shipping on orders $49 and up
These fuel injectors, Bosch part# 0 280 155 968, are very popular in many forced induction setups, as they flow enough fuel to prevent detonation at high rpm, and maintain adequate fueling. To use these on a BMW, you must have specialized tuning, as these provide far too much fuel with a stock or naturally aspirated setup. These injectors are often referred to as the "green top" or "green giant" injectors, which are also used in Ford Mustang Cobra applications. This newer generation fuel injector replaces the older style (and now discontinued) EV1 fuel injectors, often referred to as the Ford Racing EV1 fuel injector or M-9593-F302 ). They are rated at 42# / 42 pounds @ 2.7 BAR. In a BMW, which has a 3.5 BAR system, they provide approximately 47 PSI. These are sold individually, so be sure to order enough for your needs.
Show More Show Less
Bosch - Corporate Logo
T#:340644
Part#: 12137594937
In Stock
$ 30.99 USD
Free Shipping on orders $49 and up
$ 30.99 USD
Free Shipping on orders $49 and up

 

This is the OEM Bosch ignition coil that is the current replacement for most BMW 6 and 8-cylinder engines built since 2003. It's listed as a replacement coil for M54, M56, S54, N52, N54, N62, N63, N73, S63, S63TU and other engines. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed in our fitments tab. This part number replaces previous BMW part numbers 12130390064, 12130148594, 12131712219, and 12137551260.

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This Bosch part also satisfies BMW's service bulletin for 2001-2003 E46 M3 ignition coils (SIB 12 24 05). That SIB calls for Bremi or ERA brand coils but BMW has replaced them with this Bosch design.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Sold per coil. Includes connecting boot.

Show More Show Less

Race German - Corporate Logo
T#:6843920
Part#: RGDVNSDK
In Stock
$ 182.99 USD
Free Shipping
$ 182.99 USD
Free Shipping
Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. BMW introduced VANOS in the early 90s, and it added variable valve timing to the straight six engines. Over time the VANOS unit wears out which can cause error codes or VANOS rattle. Race German has sourced quality replacement parts in an easy kit. Seal Kit: 2 Large PTFE Teflon Ring Seal 2 Small PTFE Teflon Ring Seal 2 Large FKM (Viton) O Ring Seal 2 Small FKM (Viton) O Ring Seal 2 Small FKM (Viton) O Rings for Blind Plugs 2 Copper Oil Pipe Washers OEM Vanos Sealing Gasket
Show More Show Less

ARP - Corporate Logo
T#:2206
Part#: 201-6102
In Stock
$ 119.99

This product was last offered at the strikethrough price on
10-01-2026

$ 116.99 USD
Free Shipping
$ 116.99 USD
Free Shipping
Set of 12 ProSeries ARP2000 connecting rod bolts for the Euro-spec M3 engine. Made by ARP, the world leader in fastener technology. The best rod bolts available for the Euro S50 and S54. Ideal for ultra high performance, racing & forced induction applications. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in professional motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods.

This set replaces the factory BMW Euro S50B30 and B32 rod bolts with part number 11-24-1-317-184 (11241317184) and 11-24-1-405-890 (11241405890). It's also used for S54 engines with stock M10 sized rod bolts, which were used from February 2003 production and later. It was also used in earlier engines that had connecting rods replaced. For these 2001-2003 models there is no easy way to check if the rods were replaced, except by checking the rod bolt diameter. If your car has the earlier M11 sized bolt, use ARP kit #201-6103 . Before opening the ARP kit, we recommend that you check your existing rod bolt size as BMW was not consistent with their applications. ARP bolts are not returnable if the package has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1993-1999 E36 BMW Euro M3
2001-2/2003 E46 M3 coupe / convertible*
2/2003-2006 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe*
2006-2008 MZ4 M Roadster & M Coupe
* - these engines could have either M10 or M11 sized bolts. If the rods and rod bearings were replaced under recall by BMW it should have the newer M10 bolts and this is the correct ARP set to order.
Show More Show Less
ARP - Corporate Logo
T#:3315
Part#: 201-6303
In Stock
$ 212.99

This product was last offered at the strikethrough price on
10-12-2026

$ 194.99 USD
Free Shipping
$ 194.99 USD
Free Shipping
Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the 47mm length factory BMW rod bolts with part number 11-24-7-589-671 (11247589671) Check applications before ordering! Opened ARP bolt kits are not
returnable.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1999-2005 E46 BMW 328i 328ci 330i 330ci 330xi
2001-2003 E39 BMW 530i
2004-2005 E60 BMW 530i
2004-2006 E83 BMW X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 3.0i
2003-2005 Z4 BMW Z4 3.0i
Show More Show Less

ARP - Corporate Logo
T#:3606
Part#: 201-4302
In Stock
$ 240.99 USD
Free Shipping
$ 240.99 USD
Free Shipping
Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found for the E36 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines (steel block only)
1992-1995 M50 6 cylinder including 325i, 325is and 525i
1996-1999 M52 6 cylinder including 328i, 328is, 323is, 528i
1995-1995 S50US 3.0 liter including 1995 M3 (US only)
1996-1999 S52US 3.2 liter including 1996-1999 M3 (US) and MZ3
Show More Show Less
Race German - Corporate Logo
T#:6827858
Part#: RGBSCHEV1-6
In Stock
$ 40.00 USD
Free Shipping on orders $49 and up
Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. Have low fuel pressure or rough running engine? Have leaks or broken pintle caps? It may be time to rebuild your fuel injectors. This is an easy refresh kit with all the necessary parts to rebuild your BMW fuel injectors. This kit includes all filters, spacers, o-rings, and caps needed for your type of injector. *Includes fuel injector removal tool.
Show More Show Less

Race German - Corporate Logo
T#:6827863
Part#: RGBSCHEV1-6NT
In Stock
$ 25.00 USD
Free Shipping on orders $49 and up
Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. Have low fuel pressure or rough running engine? Have leaks or broken pintle caps? It may be time to rebuild your fuel injectors. This is an easy refresh kit with all the necessary parts to rebuild your BMW fuel injectors. This kit includes all filters, spacers, o-rings, and caps needed for your type of injector. *Does not include fuel injector removal tool.
Show More Show Less

Bosch - Corporate Logo
T#:19449
Part#: 16137193479
In Stock
$ 68.99 USD
Free Shipping
$ 68.99 USD
Free Shipping
Replace the defective leak diagnosis pump -often referred to as the "DTML pump" - on your BMW with this OEM unit from Bosch. This part detects vapor leaks in the fuel evaporative system.

This item fits the following BMWs:
2008+ E82 BMW 128i 135i 135is 1M Coupe
2002-2005 E46 BMW 325i 325ci 325xi 330i 330ci 330xi M3
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible
2002-2003 E39 BMW 525i 528i 530i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5
2010-3/2012 F07 BMW 535i GT, 535i xDrive GT, 550i GT, 550i xDrive GT
3/2012+ F07 BMW 550i GT, 550i xDrive GT
2011-3/2012 F10 BMW 528i (N52) 528i xDrive 535i 535i xDrive 550i 550i xDrive
3/2012+ F10 BMW 550i 550i xDrive
2004-2010 E63 BMW 645ci 650i M6
2012-3/2012 F12 BMW 640i 650i 650i xDrive
3/2012+ F12 BMW 650i 650i xDrive
2002-2006 E65 BMW 745i 745li 750i 750li 760i 760li
2009+ F01 BMW 740i 740li 750i 750li 750i xDrive 750li xDrive
2013+ E84 BMW X1 sDrive28i X1 xDrive28i X1 xDrive35i
2004-2010 E83 BMW X3 2.5i X3 3.0i X3 3.0si
2011 F25 BMW X3 xDrive28i
2011+ F25 BMW X3 xDrive35i
2002-2006 E53 BMW X5 3.0i X5 4.4i X5 4.6is X5 4.8is
2007-2013 E70 BMW X5 3.0si X5 4.8i X5 xDrive30i X5 xDrive35i X5 xDrive48i X5 xDrive50i X5M
2008+ E71 BMW X6 xDrive35i X6 xDrive50i X6M
2002-2002 Z3 BMW Z3 2.5i Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2002-2003 E52 BMW Z8 Roadster
Show More Show Less
Bosch - Corporate Logo
T#:2998
Part#: 11781742050
In Stock
$ 96.08

This product was last offered at the strikethrough price on
05-29-2026

$ 90.99 USD
Free Shipping
$ 90.99 USD
Free Shipping
This direct fit Bosch oxygen sensor plugs directly into your factory connector. It is the pre-cat sensor. No cutting or splicing required. A new oxygen sensor can improve driveability and lengthen engine life. It fits BMW E46 E39 E38 X3 X5 Z3 Z4. Bosch # 13 477.

This item fits the following BMWs:
1999-3/2003 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330xi 330ci
1999-2003 E39 BMW 525i 528i 530i M5
1997-2003 E39 BMW 540i
1995-2001 E38 BMW 750il
2004-2006 E83 BMW X3 2.5i X3 3.0i
2000-2006 E53 BMW X5 3.0i
2000-2003 E53 BMW X5 4.4i 4.6is
1999-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
2003-2005 E85 BMW Z4 2.5i Z4 3.0i
2000-2003 E52 BMW Z8
Show More Show Less
Bosch - Corporate Logo
T#:374045
Part#: 13531729319
In Stock
$ 46.99

This product was last offered at the strikethrough price on
08-03-2026

$ 37.99 USD
Free Shipping on orders $49 and up
$ 37.99 USD
Free Shipping on orders $49 and up

Fuel pressure regulators prevent excessive pressure fro building up in the fuel system. To prevent damage to fuel system components, replace your faulty regulator with a high quality OEM Bosch regulator. OEM replacement for BMW part # 13531729319 and 13531731615.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Show More Show Less


ARP - Corporate Logo
T#:2211
Part#: 201-6103
In Stock
$ 215.99 USD
Free Shipping
$ 215.99 USD
Free Shipping
Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

These bolts are M11 size to replace the stock M11 BMW bolt part number 11-24-7-834-310 (11247834310). The M11 bolt size was used in S54 engines up to 2/2003 production. However, most S54 engines up to that point had their rod bearings replaced under a factory recall and some may have had new connecting rods installed at the same time (or even a new engine altogether). The new bolts installed in these earlier engines are M10 size. Unfortunately, there is no way of knowing which rod or bolt is currently in your car (unless your car came with service records detailing when and what was replaced). The only sure way to know is to check the bolts currently installed in your engine. If yours was updated to the M10 sized bolt, use ARP kit #201-6102 . ARP bolts are not returnable if the pacakge has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
2001-2/2003 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe
Show More Show Less
Burger Motorsports - Corporate Logo
T#:26404907
Part#: 12MMSPG
In Stock
$ 35.00 USD
Free Shipping on orders $49 and up

Spark Plug Gapper Tool BMS Billet is essential for accurately adjusting the gap of spark plugs. This precision tool ensures that each plug is set to the exact specifications required for optimal engine performance. Made in the USA, it features a 12mm plug thread size, making it suitable for a wide range of applications.

  • Precision Adjustment: Allows for accurate gap adjustments to ensure optimal spark performance and engine efficiency.
  • Speed and Efficiency: Streamlines the process of gapping plugs while maintaining high precision, saving time and effort.
  • High-Quality Construction: Crafted from billet materials for durability and reliability, ensuring long-term use.
  • Lifetime Replacement Program: Comes with a lifetime replacement guarantee, reflecting confidence in the tool's quality and performance.

Upgrade your spark plug maintenance with the Spark Plug Gapper Tool BMS Billet for a reliable and precise solution.

Show More Show Less
ARP - Corporate Logo
T#:3631
Part#: 201-4303
Ships in 3 Business Days
$ 247.99 USD
Free Shipping
$ 247.99 USD
Free Shipping
Virtually every top professional BMW engine builder relies on ARP Pro Series head studs, particularly on the S54 3.2 liter engine. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best S54 head studs we've found for the E46 M3 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.​

These head studs fit the following BMWs/engines
2001-2006 E46 M3 coupe & convertible
2001-2002 MZ3 M Roadster & M Coupe (with S54 engine)
2006-2008 MZ4 Z4 M Roadster & M Coupe
Show More Show Less

Bosch - Corporate Logo
T#:2905
Part#: 12131748018
In Stock
$ 61.99

This product was last offered at the strikethrough price on
07-06-2026

$ 57.99 USD
Free Shipping on orders $49 and up
$ 57.99 USD
Free Shipping on orders $49 and up
Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.
Show More Show Less

Rein - Corporate Logo
T#:370783
Part#: 11131437237
In Stock
$ 28.99 USD
Free Shipping on orders $49 and up
Metal / Rubber gasket
Bosch - Corporate Logo
T#:23218020
Part#: 13327512019
In Stock
$ 41.99 USD
Free Shipping on orders $49 and up
BMW recommends changing your vehicle's fuel filter every 20,000 miles to keep your fuel injection system clean. This filter made by Bosch, a well-known and respected OEM part supplier, is sure to do so and provide worry-free operation for many miles.
Show More Show Less

Bosch - Corporate Logo
T#:374113
Part#: 12131740477
In Stock at Vendor
$ 28.63

This product was last offered at the strikethrough price on
11-04-2026

$ 28.41 USD
Free Shipping on orders $49 and up
$ 28.41 USD
Free Shipping on orders $49 and up

Ensure you have the best connection and seal possible with the Bosch OE spark plug boot. For vehicles with Bosch Ignition Coils.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

For BMW's with the following Engines: M52, M54, M62, M73

Show More Show Less
Bosch - Corporate Logo
T#:373840
Part#: 12317559183
In Stock
$ 37.36

This product was last offered at the strikethrough price on
10-26-2026

$ 37.25 USD
Free Shipping on orders $49 and up
$ 37.25 USD
Free Shipping on orders $49 and up

Ensure the correct voltage is being sent to/from the alternator, keep you electrical system safe from excessive voltage peaks that could cause damage to sensitive electronics and blow out fuses. Bosch's high quality unit will give you peace of mind knowing the electrical system will be safe and the voltage will remain steady. OEM replacement for BMW part # 12317559183 and 12317501752.

Cars that have oval or D shaped connector use BMW part # 12317515319

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Show More Show Less

5150 Autosport - Corporate Logo
T#:26171655
Part#: ATH-HG-CR-M50-84
Ships in 6 Business Days
$ 324.99 USD
Free Shipping on orders $49 and up
Upgrade your BMW engine's performance with the Athena Cut Ring Head Gasket. This gasket replaces BMW part # 11121726619 and 11121726617 and is specifically designed for M50 & M52 iron block inline 6-cylinder engines found in E34/E36 chassis. Standard OEM & MLS gaskets can only handle a certain amount of cylinder pressure before they start to leak, making the Athena Cut Ring Head Gasket the recommended choice for applications making 16+ psi. A compression leak passing the head gasket can cause a range of issues, including engine overheating, loss of power, misfires, and in severe cases, catastrophic engine failure. Athena's gasket is crafted with premium quality reinforced M0115, an asbestos-free material that's original equipment approved and renowned for its superior quality. The AISI 304 stainless steel Cooper Rings bite into the aluminum head, providing maximum sealing capabilities around the cylinder bore and optimizing engine performance, even on engines with nitrous and/or turbo applications that exceed 2-bar boost. Before installation, it is crucial to have the mating surfaces of the cylinder head and block professionally cleaned and resurfaced to ensure they are completely flat. Please be aware that the gasket should have a size that is 0.5mm to 1mm larger than the piston. For example, if the piston measures 84mm, then the gasket should be the next size up, either 84.5mm or 85mm. Installation instructions: Make sure that the engine block and cylinder head surfaces are clean, flat, and free from any debris, oil, or coolant. Install the Cut Ring gasket on the engine block and ensure that it is properly aligned. Avoid twisting or bending the gasket during installation. Place the cylinder head on top of the gasket and install the head bolts or studs in their correct positions. Follow the manufacturer's recommended torque specifications and tighten the bolts or studs in the proper sequence to ensure even clamping force across the gasket. After the initial tightening, re-torque the head bolts or studs after the engine has been started and then allowed to cool to room temperature. This will ensure that the gasket is properly seated and compressed. It is recommended to not use any additional sealant on the MLS gasket, as it is already coated with a Viton rubber sealant. Using additional sealant can hinder the performance of the gasket.
Show More Show Less

Race German - Corporate Logo
T#:6843928
Part#: RGS54VNSK
In Stock
$ 47.99 USD
Free Shipping on orders $49 and up
Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. BMW introduced VANOS in the early 90s, and it added variable valve timing to the straight six engines. Over time the VANOS unit wears out which can cause error codes or VANOS rattle. Race German has sourced quality replacement parts in an easy kit. Seal Kit: 6 Orings 4 Sealing rings
Show More Show Less
Race German - Corporate Logo
T#:6843919
Part#: RGDVNSSRK
Ships in 2 Business Days
$ 101.99 USD
Free Shipping
$ 101.99 USD
Free Shipping
Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. BMW introduced VANOS in the early 90s, and it added variable valve timing to the straight six engines. Over time the VANOS unit wears out which can cause error codes or VANOS rattle. Race German has sourced quality replacement parts in an easy kit. Seal Kit: 2 Large PTFE Teflon Ring Seal 2 Small PTFE Teflon Ring Seal 2 Large FKM (Viton) O Ring Seal 2 Small FKM (Viton) O Ring Seal 2 Small FKM (Viton) O Rings for Blind Plugs 2 Copper Oil Pipe Washers 2 Anti Rattle Bushing Set (2 Bushing + 4 Bearings)
Show More Show Less
Bosch - Corporate Logo
T#:348133
Part#: 12137594937T6KT
In Stock
$ 185.99 USD
Free Shipping
$ 185.99 USD
Free Shipping

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Show More Show Less


Bosch - Corporate Logo
T#:2995
Part#: 11781405324
In Stock
$ 117.99 USD
Free Shipping
$ 117.99 USD
Free Shipping
This is the pre-cat oxygen sensor for cylinders 4-6 for BMW E46 M3.Bosch # 13 952.

This item fits the following BMWs:
2001-2006 E46 BMW M3 M3 convertible
2001-2002 Z3 BMW M Roadster M Coupe
Show More Show Less
Bosch - Corporate Logo
T#:340543
Part#: FGR7DQP-6
In Stock
$ 59.99

This product was last offered at the strikethrough price on
10-21-2026

$ 53.99 USD
Free Shipping on orders $49 and up
$ 53.99 USD
Free Shipping on orders $49 and up

Spark Plug Replacement for Enhanced Engine Performance

Periodic replacement of spark plugs is crucial in averting common problems arising from worn or contaminated plugs. Issues like misfires, reduced power, and a lit Check Engine Light are effectively prevented by timely plug replacements.

Fresh spark plugs not only boost engine performance and fuel efficiency but also play a significant role in reducing engine misfires, subsequently preserving expensive ignition coils and catalytic converters.

Turner Motorsport provides an array of brands, plug configurations, and heat ranges meticulously recommended by OEMs for various European applications, ensuring optimal performance and compatibility.

Benefits:

  • Prevents misfires and engine performance issues
  • Enhances fuel efficiency
  • Reduces strain on ignition coils and catalytic converters
  • Recommended by OEMs for European applications
Show More Show Less
Race German - Corporate Logo
T#:6827878
Part#: RGSMNS6NT
In Stock
$ 29.99 USD
Free Shipping on orders $49 and up
Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. Have low fuel pressure or rough running engine? Have leaks or broken pintle caps? It may be time to rebuild your fuel injectors. This is an easy refresh kit with all the necessary parts to rebuild your M54 fuel injectors. This kit includes all filters, spacers, o-rings, and caps needed for your type of injector. *Does not include fuel injector removal tool.
Show More Show Less

Bosch - Corporate Logo
T#:384364
Part#: 12412354693
In Stock
$ 269.99 USD
Free Shipping
$ 269.99 USD
Free Shipping

If your car won't turn over, there is a good chance your starter is shot. Bosch's OEM starter is a high quality replacement that will give you peace of mind thanks to its long life-span. OEM replacement for BMW part # 12412354693, 12412344242, 12412167996.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

For BMW's with the M54 engine with a production date from 09/2002.

Show More Show Less

Bosch - Corporate Logo
T#:3303
Part#: 11787523434
In Stock
$ 203.99 USD
Free Shipping
$ 203.99 USD
Free Shipping
This is the pre-cat oxygen sensor for bank 1 - cylinders 1-3 for BMW E46 E60 E83 X3 Bosch # 17 215.

This item fits the following BMWs:
3/2003-2005 E46 BMW 325i 325ci 325xi with M54 engine.
3/2003-2005 E46 BMW 330i 330ci 330xi
2004-2005 E60 BMW 525i 530i
2004-2006 E83 BMW X3 3.0i - Automatic Transmission Only
Show More Show Less
Mishimoto - Corporate Logo
T#:597051
Part#: MMOCCLA
In Stock
$ 127.99 USD
Free Shipping
$ 127.99 USD
Free Shipping
WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

ARP - Corporate Logo
T#:2210
Part#: 201-6201
Ships in 7 Business Days
$ 222.99

This product was last offered at the strikethrough price on
08-13-2026

$ 194.99 USD
Free Shipping on orders $49 and up
$ 194.99 USD
Free Shipping on orders $49 and up
Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the factory BMW rod bolt number 11-24-1-739-728 (11241739728) which measures 44mm in length. The 44mm BMW rod bolt was used on all US spec E36 M3 (3.0 and 3.2 liter), 1999-2000 E46 323i/323Ci, 2001-2005 325i/325Ci, Z3 1.9,2.5 and 3.2, as well as Z4 2.5. It was also used on SOME of the M50 2.5 liter engines from 1992-1995 -- but check before ordering! Opened ARP bolt kits are not returnable. If your M50 2.5 liter engine has 53mm rod bolts, you will require kit part# 201-6301 instead.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1992-1995 E36 325i/is *** with 44mm rod bolts only ***
1995-1995 E36 M3 S50 3.0 liter (US model)
1996-1999 E36 M3 S52 3.2 liter (US model)
1999-2000 E46 323i & 323Ci (US)
2001-2005 E46 325i, 325xi & 325Ci (US)
1998-2002 Z3 2.3 / 2.5 liter
1998-2000 MZ3 M Roadster & M Coupe
2003-2005 Z4 2.5 liter
*** DOES NOT FIT E36 328 ****
Show More Show Less
OEM Bosch Ignition Coil - Set of 6 - M54 S54 BMW
For vehicles with production date from 09/2002
Bosch - Corporate Logo
T#:340693
Part#: 12131712219
In Stock
$ 185.99 USD
Free Shipping
$ 185.99 USD
Free Shipping
Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their exacting assembly process and high level of durability you can expect a long service life from all Bosch products.
Show More Show Less

Mishimoto - Corporate Logo
T#:380389
Part#: MMOCF-BMW
In Stock
$ 88.99 USD
Free Shipping
$ 88.99 USD
Free Shipping
Install a custom oil cooler on your street or track BMW with help from the Mishimoto Oil Line Fitting Kit! This kit has 100% CNC-machined components, including the 6061 aluminum oil line fittings and the 303 stainless steel tie-down plate. This adapter kit is applicable for BMW E36 (Euro oil-housing equipped), E46, and E90 vehicles, and allows for the use of -10AN fittings to route oil to a custom oil cooler setup. This is an ideal upgrade for drivers seeking additional cooling for track environments or for those who would like additional engine bay space for an oil accumulator or supercharger setup. Included in this kit are two stock BMW O-rings for leak-free installation. Features: Allows for use of -10AN fittings for custom oil cooler setup 100% CNC-machined components, including 6061 aluminum fittings and 303 stainless steel tie-down plate Includes durable stock BMW O-rings for leak-free installation Provides additional engine bay space for applications with an oil accumulator or supercharger setup Included as part of the Mishimoto BMW E46 M3 Oil Cooler Kit Mishimoto Lifetime Warranty Included: (1) Stainless Steel Fitting Clamp (2) -10AN Fittings (2) BMW Oil O-rings (1) M8 x 1.25 x 25mm Button-Head Bolt Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov. ​
Show More Show Less

Bosch - Corporate Logo
T#:370775
Part#: 12317831436
In Stock
$ 322.99

This product was last offered at the strikethrough price on
08-23-2026

$ 293.99 USD
Free Shipping
$ 293.99 USD
Free Shipping

A replacement Bosch alternator for the 2001-2006 M3. Bosch is an original equipment supplier to BMW, and is the finest and most recognized German brand of alternator available. The Original BMW alternator sells for over double! Buy only the best alternator for your BMW -- buy a Bosch alternator. This is an OEM replacement for BMW part # 12317831436.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

A $80.00 refundable core charge must be applied to this alternator. Upon receipt of your rebuildable alternator core, you will be refunded the core charge. 

This item fits the following BMWs:
2001-2006 E46 BMW M3, M3 Convertible
2001-2002 Z3 BMW M Roadster M Coupe

Show More Show Less
ARP - Corporate Logo
T#:2192
Part#: 201-5002
In Stock at Vendor
$ 171.99 USD
Free Shipping on orders $49 and up
This ARP main stud set is for the S54 3.2 liter, as found in all 2001 to 2006 E46 M3, as well as the 2006-2008 Z4 M Roadster and M Coupe models. Switching to the ARP main stud kit eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This S54 main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This ARP main stud kit fits the following BMWs:
2001-2006 E46 M3 3.2 liter coupe/convertible
2001-2002 MZ3 M Coupe & M Roadster (S54 engine)
2006-2008 MZ4 M Coupe & M Roadster
Show More Show Less
Rein - Corporate Logo
T#:379190
Part#: 11617504535K
Ships in 1 Business Day
$ 79.99 USD
Free Shipping
$ 79.99 USD
Free Shipping

Turner Motorsport presents the Crankcase Ventilation System Refresh Kit for BMW owners experiencing malfunctioning or aged CCV systems. This comprehensive kit includes all necessary hoses to complete a refresh, ensuring optimal performance and reliability for your BMW's CCV system.

  • Addresses malfunctioning CCV systems
  • Ensures proper ventilation of the crankcase
  • Comprehensive kit includes all necessary hoses
  • Restores performance and reliability
  • Compatible with various BMW models
Show More Show Less


Race German - Corporate Logo
T#:6827877
Part#: RGSMNS6
In Stock
$ 47.99 USD
Free Shipping on orders $49 and up
Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. Have low fuel pressure or rough running engine? Have leaks or broken pintle caps? It may be time to rebuild your fuel injectors. This is an easy refresh kit with all the necessary parts to rebuild your M54 fuel injectors. This kit includes all filters, spacers, o-rings, and caps needed for your type of injector. *Includes fuel injector removal tool.
Show More Show Less
Bosch - Corporate Logo
T#:2996
Part#: 11781743994
In Stock
$ 193.99

This product was last offered at the strikethrough price on
08-03-2026

$ 145.37 USD
Free Shipping
$ 145.37 USD
Free Shipping

Bad oxygen sensors can cause check engine lights and poor fuel mileage. Replace your faulty sensor with this high quality Bosch sensor to turn off your check engine light and restore fuel mileage.

This is the pre-cat oxygen sensor for cylinders 1-3 for BMW E46 M3. Bosch # 13 949. This is a OEM replacement part for BMW part # 11781743994.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!


This item fits the following BMWs:
2001-2006 E46 BMW M3 M3 convertible
2001-2002 Z3 BMW M Roadster M Coupe

Show More Show Less
Bosch Flow Matched EV14 Injectors - US CAR Connector (EV6) - 750cc - ...
NOT A DIRECT REPLACEMENT FOR FACTORY INJECTORS - For use with aftermarket port injectio...
Bosch - Corporate Logo
T#:36947243
Part#: 501-0028
In Stock
$ 415.99 USD
Free Shipping on orders $49 and up
$ 415.99 USD
Free Shipping on orders $49 and up
The Black Market Parts Genuine Bosch Motorsports EV14 fuel injectors featuring USCAR (EV6) connector matched and packaged in a pack of 6 units. Direct plug-in for Motiv Reflex, AIC, and Nexsys Motorsports
Show More Show Less

Bosch - Corporate Logo
T#:2118
Part#: 11781433940
In Stock
$ 147.99 USD
Free Shipping
$ 147.99 USD
Free Shipping
This is the post-cat oxygen sensor for cylinders 4-6 for BMW E46 E39 X3 X5 Z3 Z4. Bosch # 15 109.

This item fits the following BMWs:
1999-3/2003 E46 BMW 323i 323ci 325xi 328i 328ci 330i 330ci 330xi
2001-3/2003 E46 BMW 325i 325ci only for cars with M54 engine
1999-2003 E39 BMW 528i 525i 530i
2004-2006 E83 BMW X3 2.5 - Bank 1 Only
2004-2006 E83 BMW X3 3.0i - Bank 1 - Automatic Transmission Only
2000-2006 E53 BMW X5 3.0i
1999-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
2003-2006 E85 BMW Z4 2.5i Z4 3.0i
Show More Show Less

Bosch - Corporate Logo
T#:583735
Part#: 12317501690
In Stock
$ 415.99 USD
Free Shipping
$ 415.99 USD
Free Shipping

If your car has died on the side of the road from a dead battery and you notice flickering or low powered headlights, it's likely your alternator failing. To be sure you are getting a high-quality part with a long life-span, choose this OEM Bosch Alternator. This is a brand new OEM replacement for BMW part # 12317501690.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Show More Show Less
Rein - Corporate Logo
T#:361056
Part#: 11142249533
In Stock at Vendor
$ 22.99 USD
Free Shipping on orders $49 and up
Rein Rear Crankshaft Seal for many BMW models is an OE-equivalent replacement for the rear main oil seal. When the seal fails, oil drips onto the driveway and can reach the clutch surface. Replacing it during a clutch job is the practical time to do it, since the transmission is already out.
Show More Show Less

Mishimoto - Corporate Logo
T#:372557
Part#: MMOCCCF
In Stock
$ 162.99 USD
Free Shipping
$ 162.99 USD
Free Shipping
Universal kit with a catch can and rubber hose; for retrofitting on a variety of vehicles. Carbon fiber catch can prevents a harmful buildup of oil inside of the turbocharger, intake manifold, intercooler and piping. Separates oil particles from PCV/CCV air Defends intercooler, intake system, and essential components from oil blow-by Made from lightweight carbon fiber Compact design makes for easy engine bay placement Checking fluid levels made easy with built in sight tube Comes complete with mounting bracket, hose, all necessary clamps, fittings, and mounting hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

Bosch - Corporate Logo
T#:2675
Part#: 11781406622
Ships in 3 Business Days
$ 208.90

This product was last offered at the strikethrough price on
05-19-2026

$ 157.99 USD
Free Shipping
$ 157.99 USD
Free Shipping
This oxygen sensor fits the following BMWs:
2001-2006 E46 3 Series M3 M3 Convertible
2001-2002 Z3 M Z3 M Roadster Z3 M Coupe with S54 engine
2006-2008 E85 E86 Z4 M Z4 M Roadster Z4 M Coupe
Show More Show Less

Rein - Corporate Logo
T#:591711
Part#: 11511436590
In Stock
$ 50.99

This product was last offered at the strikethrough price on
10-22-2026

$ 46.99 USD
Free Shipping on orders $49 and up
$ 46.99 USD
Free Shipping on orders $49 and up
A common failing piece due to the plastic design.
Burger Motorsports - Corporate Logo
T#:583132
Part#: BMSBSPGT14MM
Ships in 7 Business Days
$ 35.00 USD
Free Shipping on orders $49 and up

BMS Billet Spark Plug Gapper Tool - 14mm is an essential tool for achieving accurate and consistent spark plug gapping, ideal for automotive enthusiasts and professional mechanics alike. This precision tool helps maintain optimal plug performance by providing reliable, consistent gaps. Available in both 14mm and 12mm plug thread sizes, this tool is proudly made in the USA to deliver durability and precision.

  • Precisely gaps spark plugs for enhanced engine performance and efficiency
  • Speeds up the gapping process while ensuring accuracy and uniformity
  • Available in two sizes (14mm and 12mm) for a wider range of compatibility
  • Optional specialty feeler gauge included with 4 blades in thicknesses of .018, .020, .022, and .024
  • Made in the USA for premium quality and durability
Show More Show Less
Rein - Corporate Logo
T#:4471
Part#: 11361705532
Ships on Dec 1, 2026
$ 61.99

This product was last offered at the strikethrough price on
06-04-2026

$ 53.99 USD
Free Shipping on orders $49 and up
$ 53.99 USD
Free Shipping on orders $49 and up
This oil pipe hose runs from the VAN0S adjusting unit to the oil filter housing. At some point the rubber line shrinks or cracks and oil can weep out of the swedge fittings. The fittings at the banjo bolts can also leak so replacing the seals for each banjo fitting is strongly recommended.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

This item fits the following BMWs:
1996-1999 E36 BMW 323is 323ic 328i 328is 328ic M3 3.2
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1997-2003 E39 BMW 525i 528i 530i
2004-2005 E60 BMW 525i 530i
2004-2006 E83 BMW X3 2.5i X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i
Show More Show Less


Bosch Flow Matched EV14 Injectors - US CAR Connector (EV6) - 950cc - ...
NOT A DIRECT REPLACEMENT FOR FACTORY INJECTORS - For use with aftermarket port injectio...
Bosch - Corporate Logo
T#:47679242
Part#: 501-0082
In Stock
$ 572.99 USD
Free Shipping on orders $49 and up
$ 572.99 USD
Free Shipping on orders $49 and up
The Black Market Parts Genuine Bosch Motorsports EV14 fuel injectors featuring USCAR (EV6) connector matched and packaged in a pack of 6 units. Direct plug-in for Motiv Reflex, AIC, and Nexsys Motorsports
Show More Show Less
Bosch - Corporate Logo
T#:16242205
Part#: FGR7DQE0-6
Ships in 1 Business Day
$ 55.99 USD
Free Shipping on orders $49 and up