Select Vehicle
BMW
Mini
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
Turner Motorsport Lightweight N54 Flywheel & Upgraded Clutch Kit
Unlock the full potential of your N54-powered BMW with our performance-driven clutch and flywheel kit. Designed to enhance daily drivability while delivering increased power handling and improved throttle response, this kit is the ultimate upgrade for enthusiasts seeking more from their vehicle.
Why Choose This Kit?
This setup features the Turner Lightweight N54 Flywheel, precision-engineered for quicker acceleration, faster rev-matching, and a more responsive driving experience. Paired with an upgraded OE clutch from the high-performance 335is and F10 550i(V8 Bi-Turbo), this combo is capable of handling over 500 ft-lbs of torque while maintaining smooth, factory-like engagement and durability.
The factory dual-mass flywheel may prioritize smoothness and efficiency, but it comes at the cost of responsiveness and is prone to failure in high-performance applications. The Turner Lightweight Flywheel solves these issues with a single-mass design that strikes the perfect balance between comfort, performance, and reliability making it ideal for both daily driving and spirited track use.
Kit Contents:
Turner Lightweight N54 Single-Mass Flywheel (18.6 lbs, 10 lbs lighter than stock)
Upgraded OE Clutch – Supports 500 ft-lbs+
OE Clutch Fork - P# 21517564027
OE Throwout Bearing
Clutch Alignment Tool - P# 056212LA01A
Brass Clutch Fork Pivot Pin - P# 21511223328
OE Flywheel Bolts - P# 11227520706
OE Pressure Plate Screws - P# 21207548052
Pivot Pin Retaining Spring - P# 21517570284
Transmission Mating Dowels - P# 11117524470
Flywheel Features:
Precision-machined 4140 HT heat-treated chromoly steel for durability
Black oxide coating to resist corrosion
8620 steel pilot bearing pin for maximum wear resistance
Precision balanced to exceed OEM standards
Optimized step height for longer clutch life and consistent performance
Clutch:
Upgrade for 135i/335i/535i models from the 335is! Featuring a heavy-duty clutch with more holding power and a stock-like pedal feel. Excellent solution for If your clutch is slipping, or the engagement isn't what it used to be, it's time for a replacement. Slipping clutches won't allow your BMW to accelerate properly and can pose problems under a load such as going up large inclines. Also, a worn clutch can cause less precise and engaging shifts. By replacing your clutch you will restore performance and driving pleasure.
This clutch is an excellent upgrade for non 335is/550i/650i models. It features a more heavy-duty clutch disc and more holding power with stock-like pedal effort.
Transform your driving experience with this Turner Motorsport clutch and flywheel kit - engineered for power, performance, and everyday reliability.
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
Turner Motorsport Lightweight N55 Flywheel & Upgraded Clutch Kit
Unlock the full potential of your N55-powered BMW with our performance-driven clutch and flywheel kit. Designed to enhance daily drivability while delivering increased power handling and improved throttle response, this kit is the ultimate upgrade for enthusiasts seeking more from their vehicle.
Why Choose This Kit?
This setup features the Turner Lightweight N55 Flywheel, precision-engineered for quicker acceleration, faster rev-matching, and a more responsive driving experience. Paired with an upgraded OE clutch from the high-performance 335is and F10 550i(V8 Bi-Turbo), this combo is capable of handling over 500 ft-lbs of torque while maintaining smooth, factory-like engagement and durability.
The factory dual-mass flywheel may prioritize smoothness and efficiency, but it comes at the cost of responsiveness and is prone to failure in high-performance applications. The Turner Lightweight Flywheel solves these issues with a single-mass design that strikes the perfect balance between comfort, performance, and reliability making it ideal for both daily driving and spirited track use.
Kit Contents:
Turner Lightweight N55 Single-Mass Flywheel (18.6 lbs, 10 lbs lighter than stock)
Upgraded OE Clutch – Supports 500 ft-lbs+
OE Clutch Fork - P# 21517564027
OE Throwout Bearing
Brass Clutch Fork Pivot Pin - P# 21511223328
OE Flywheel Bolts - P# 11227520706
OE Pressure Plate Screws - P# 21207548052
Pivot Pin Retaining Spring - P# 21517570284
Transmission Mating Dowels - P# 11117524470
Flywheel Features:
Precision-machined 4140 HT heat-treated chromoly steel for durability
Black oxide coating to resist corrosion
Precision balanced to exceed OEM standards
Optimized step height for longer clutch life and consistent performance
Clutch:
Upgrade for 135i/335i/535i models from the 335is! Featuring a heavy-duty clutch with more holding power and a stock-like pedal feel. Excellent solution for If your clutch is slipping, or the engagement isn't what it used to be, it's time for a replacement. Slipping clutches won't allow your BMW to accelerate properly and can pose problems under a load such as going up large inclines. Also, a worn clutch can cause less precise and engaging shifts. By replacing your clutch you will restore performance and driving pleasure.
This clutch is an excellent upgrade for non 335is/550i/650i models. It features a more heavy-duty clutch disc and more holding power with stock-like pedal effort.
Transform your driving experience with this Turner Motorsport clutch and flywheel kit - engineered for power, performance, and everyday reliability.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
This is the stock twin mass flywheel for the N55 engine used in the E82 135i, E9X 335, F3x 335/435, and F10 535i. It's manufactured by OEM supplier LuK. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.
The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.
DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.
A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.
This item fits the following BMWs with the single turbo N55 engine and manual transmission:
2011-2012 E82 BMW 135i
2011 E90 BMW 335i 335xi 335i xDrive - Sedan
2011-2013 E92 BMW 335i 335xi 335i xDrive - Coupe
2011-2013 E93 BMW 335i - Convertible
2012-2015 F30 BMW 335i 335iX - Sedan
2014-2016 F34 BMW 335iX - Gran Turismo
2014-2016 F32 BMW 435i 435iX - Coupe
2014-2016 F33 BMW 435i 435iX - Convertible
2014-2016 F36 BMW 435i 435iX - Gran Coupe
2011+ F10 BMW 535i 535i xDrive
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
This is the stock OE BMW twin mass flywheel for the N54 engine in later E82 135i, E9X 335i, E60 535i, and Z4 35i (cars with 6-bolt mounting hub). Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.
The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.
DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.
A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.
This item fits the following BMWs:
1/2009-2010 E82 BMW 135i
1/2009-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
1/2009-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
1/2009-2010 E93 BMW 335i - Convertible
1/2009-2010 E60 BMW 535i 535xi 535i xDrive
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
This is the stock twin mass flywheel for the E92/E93 335is N54. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.
The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.
DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.
A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.
New flywheel mounting bolts must be ordered separately.
This item fits the following BMWs:
1/2009-2013 E92 BMW 335is - Coupe, DCT transmission
1/2009-2013 E93 BMW 335is - Convertible, DCT transmission