Genuine BMW BMW Drivetrain Parts for BMW 3 Series E92 (2007-2013)

This is the stock OE BMW twin mass flywheel for the N54 engine in later E82 135i, E9X 335i, E60 535i, and Z4 35i (cars with 6-bolt mounting hub). Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

This item fits the following BMWs:
1/2009-2010 E82 BMW 135i
1/2009-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
1/2009-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
1/2009-2010 E93 BMW 335i - Convertible
1/2009-2010 E60 BMW 535i 535xi 535i xDrive

This is a complete differential to change the gearing of a manual transmission E90/E92 325i, 328i, or 330i (not for xi models) to a 3.64 ratio final drive. The standard gearing on the manual transmission cars is 3.15 or 3.23, making this E90 diff significantly shorter. This diff is from a 330i automatic where the gear ratio has to be shorter to make up for the transmission gearing differences and extra weight. This will dramatically improve acceleration on any 325i, 328i or 330i INSTANTLY! If you are looking for better off-the-line or rolling acceleration, and are willing to sacrifice a little top-speed (some of us don't get up to 150mph), this is one of the best ways to achieve it with almost no downside. There are few things that can improve your 0-to-60 and 0-to-100 times as much as shorter gearing, and this differential is clearly a best "bang-for-buck" solution for dramatically better acceleration. Since this is an Original BMW part it carries the same BMW two year warranty as any other new part. So there's no need to take a chance on a used part from a private seller. (former BMW part number 33107519944)

Changing gear ratio changes the RPM range for any given speed. Use the chart below for examples of speed vs RPM changes for the 3.64 diff.
 

2006 330i, 6-speed manual, stock 3.15 gears, 255/35-18" rear tires

Gear RatioGearSpeedRPM

40 MPH in 4th

3.154th40 MPH2,100 RPM

3.644th40 MPH2,400 RPM

70 MPH Cruise

3.156th70 MPH2,500 RPM

3.646th70 MPH2,900 RPM

5th Gear Speed @ 6,000 RPM

3.155th142 MPH6,000 RPM

3.645th123 MPH6,000 RPM

Why 5th? Because 6th does not have the mechanical advantage to get past wind resistance at these speeds - it is more of a cruise/overdrive gear. Using 5th for comparison purposes is much more relevant than having to take into account wind direction, resistance, grade, elevation, tire sizing, etc. These numbers are for comparisons among gear ratios only, not to determine what your E90 will top out at.2006-2011 325i or 328i, 6-speed manual, stock 3.23 gears, 255/35-18" rear tires

(click to expand)

Gear RatioGearSpeedRPM

40 MPH in 4th

3.234th40 MPH2,150 RPM

3.644th40 MPH2,400 RPM

70 MPH Cruise

3.236th70 MPH2,600 RPM

3.646th70 MPH2,900 RPM

5th Gear Speed @ 6,000 RPM

3.235th138 MPH6,000 RPM

3.645th123 MPH6,000 RPM

Speed in 5th gear at 6,000 RPM is for theoretical and comparison purposes only. It doesn't mean that these speeds are actually reachable.

A $100 refundable core charge must be added at the time of order. This core charge can be refunded when you ship your original diff back to us.

This item fits the following BMWs with manual transmission only:
2006-2011 E90 BMW 325i 328i 330i - Sedan
2006-2012 E91 BMW 325i 328i - Wagon
2007-2013 E92 BMW 328i - Coupe
2007-2013 E93 BMW 328i - Convertible

BMW E60 E90 E92 Re Manufactured Front Differential from Turner Motorsport offers a reliable and cost-effective solution to restore your BMW's drivetrain performance. This high-quality, re-manufactured differential is engineered to meet or exceed OEM standards, ensuring smooth power delivery and optimal handling. Designed to replace a worn or damaged differential, this unit provides the dependability and durability you expect from Turner Motorsport's expertise in BMW components.

• Precision re-manufactured to meet OEM specifications
• Enhances power distribution and vehicle handling
• Cost-effective alternative to a new differential
• Designed for a smooth and quiet driving experience
• Backed by Turner Motorsport’s commitment to quality

Replace your worn front differential with the BMW E60 E90 E92 Re Manufactured Front Differential for a renewed driving experience and superior performance.