Select Vehicle
BMW
Mini
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
Engineered in-house, we designed this lightweight, single-mass flywheel to provide more than 10 pounds of weight savings over the factory flywheel. While some ultra-lightweight performance flywheels are manufactured from aluminum, our designers opted for a more driveable experience with steel. The mass provided by steel helps dampen vibrations and noise, delivering near-factory refinement with most of the benefits of a lightweight flywheel: quicker throttle response, improved durability (and longevity), and more effective transfer of power to the wheels.
Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.
When it comes to selecting a clutch to pair with a lightweight flywheel, consider the driving you’ll be doing. As a single mass flywheel eliminates the dual-mass dampening of the factory flywheel, to retain the lowest noise, lowest harshness driving experience possible, select a clutch with a dampened disc. For dedicated track cars, a solid clutch hub is appropriate.
*Click here for installation instructions
Our recommendations:
Features:
Performance:
Stock flywheel weight - 28.9lbs
Turner single mass flywheel weight = 18.55lbs
This item fits the following BMWs with 8 bolt flywheel and build date up to 01/2009 or earlier:
2008-01/2009 E82 BMW 135i 135is 1M
2007-01/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-01/2009 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
2007-01/2009 E93 BMW 335i 335is - Convertible
2008-01/2009 E60 BMW 535i 535xi 535i xDrive
If allowed in the rules these solid aluminum engine and transmission mounts offer many advantages over urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. These are machined from solid aluminum and have zero deflection, engine torque will cause a rubber or urethane mount to flex or deflect allowing more torque to passed through the drive line (instead of being wasted winding up the mount). When paired with our flex-free solid transmission mounts you'll get smoother, crisper shifts since the transmission is no longer dancing on the pliable mount. This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of motor and transmission mounts you will ever need. We very strongly recommend using the solid transmission and engine mounts together as a complete kit, mixing a rubber mount with a metal mount will cause undue stress on the mounting points and will lead to a failure. We never advise using a solid engine mount unless a corresponding solid transmission mount is also used.
These are a no-compromise design for all-out racing use, full solid aluminum mounts should not be used on street-driven cars since there is no material to absorb vibration making these quite harsh for regular street use (track cars don't care about noise).
Product features and benefits:
This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335i - Sedan
2007-2011 E91 BMW 325i 328i - Touring Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
A full overhaul of your shift setup. Short shift upgrade featuring an exclusive N54 DSSR, poly carrier bushing and associated components to transform your driving experience.
The double-adjustable short shifter kit features both shift lever height and throw adjustment to dial in the exact shifter feel you are looking for. Paired with the N54 DSSR this kit features upgraded replacements for your entire shift assembly with a whole new shift carrier, bushings, lever, and selector rod. Did we mention this will work with any factory-style press on shift knob?
If you're aiming to install a short throw shifter setup or completely rejuvenate your shifting assembly, this comprehensive kit is your perfect solution. It leaves no aspect untouched, upgrading all components simultaneously, eliminating the need for troubleshooting later to address any play in your shifter. We've all experienced the frustration of piecemealing upgrades, only to find ourselves cobbling together the rest of the kit in a longer, more tedious process. With this kit, you can get it right the first time and avoid any disappointment.
Performance advantages:
Adjustable between a conservative short throw to an ultra-short throw
Ultra crisp shifter feel - quicker, more precise shifts
More engaging driving experience
Design:
CNC machined chromoly steel shift lever assembly with 304ss shifter ball
Nylatron bushings
6061 Bearing cup assembly with type 2 anodizing for an amazing look and corrosion reistance
Shift level is compatible with OE BMW and aftermarket shift knobs
Reduced deflection from the rigid DSSR
Kit Contents:
Shifter arm assembly - 25117545110
Shifter arm bushings - 25117528407
Bearing pins - (25117529078 and 25117529079)
Turner poly rear shifter arm bushing - (25111222015 and 25111222652)
Shift lever assembly - 25117555911
Shifter lever cap assembly
Short shift lever adapter
E8x/E9x DSSR - 25117524722
Single piece 6061 construction, optimized cooling, provisions for temp sensor, and external cooler with removable air duct.
Built to last, made from a single piece of 6061 billet aluminum with a rugged and good-looking hard-coat anodizing the Turner diff cover can handle anything you throw at it. Not only is it an absolute masterpiece, but this billet diff cover checks all the boxes for features needed. Reinforced mounting ear for strength and stability. The mounting ear is unified with the one-piece billet cover and features added material for the highest durability possible. This diff cover is cool, literally, the entire construction was designed with optimized cooling in mind. External fins are strategically placed on the rear face, bottom, and between the mounting ears of the cover, serving as effective heat sinks for optimal heat dissipation. This ensures stable temperatures, promoting longevity for both the fluid and your differential. Additionally, the internal design ensures continuous oiling and lubrication of the ring gear, maintaining its stability and preventing fatigue by controlling heat more effectively. An internal baffle at the cover's corner helps maintain proper pressure and prevents cavitation.
All of the OEM features were retained along with the upgrades. The drain and fill plugs on the diff cover are upgraded to -6AN using the provided high-pressure fittings with replaceable o-rings. The drain and fill plugs can now be used for an external oil cooler allowing you to further expand the fluid capacity for optimized cooling and service intervals. To keep an eye on things from the driver seat is 1/8 NPT provision for temp sensors, this product from Turner has you covered at every turn.
Upgrading to our Turner Billet Differential cover gives you the strength you need to push your car to its limits without worrying about snapping a diff mount from clutch kicking or other shocks to the drivetrain. In addition to its enhanced strength, this differential cover includes numerous other upgrades and conveniences. These include improved cooling and lubrication for the ring gear, upgraded fill and drain plugs, and the option to expand an external oil cooler for extreme motorsport usage. Designed to complement both upgraded daily drivers and extensively modified track cars, it also offers a visually appealing design.
Key Benefits:
Reinforced mounting ear for strength and stability
16% Increased fluid capacity
External fins on the back side, bottom, and mounting ear on the casing for maximum cooling and consistent fluid temps
Removeable air duct to direct air across the cooling fins for even more temperature control
Optimized internal design to keep fluid consistently on the ring gear
Integrated breather to prevent cavitation by venting the appropriate amount of pressure being built up in the diff housing
-6AN ports to incorporate the use of a differential cooler - this increases capacity and lowers temps allowing for extended fluid change intervals
1/8 NPT fitting for the use of a temp sensor to monitor fluid temperature
Design:
Fits manual transmission Large Case 215mm differentials
Single piece 6061 Billet aluminum construction
T6 Black hard coat anodizing for superior corrosion resistance and aesthetics
Compatible with most differential coolers(-6AN) and temp sensors(1/8 NPT)
Designed to accommodate oversized rear sway bars
Retains OEM mounting features
Factory geometry bushing size for use with OEM and aftermarket poly bushings
Removeable air duct for easy access to sensors and drain/fill plug
Rubber engine and transmission mounts for a street car and solid aluminum for the track, right? Well, it's not that straightforward anymore.
Stock rubber fluid-filled mounts are designed to be soft and comfortable, limiting the NVH (noise, vibration, and harshness) felt by the driver. The drawback inherent with a conventional design is driveline deflection, making it more difficult to put the power to the wheels, as well as making a money-shift or miss-shift more likely as they age. Solid mounts are exactly the opposite of this - they permit tons of NVH while offering zero deflection, making these a must have for track-driven vehicles looking to capitalize on every ounce of performance available. Enthusiasts looking to find the best of both worlds often look to polyurethane engine mounts - and many are disappointed with other designs on the market. Seeking a mount that offers a positive connection yet doesn't deform, fail, or rattle the fillings out of their mouths is frequently a lost cause.
Until now.
We engineered these mounts with these very concerns in mind. We know if a soft mount offers a sloppy connection it doesn't work on the track, and a solid mount isn't acceptable as a daily driver (for most!) and set out to engineer a mount that would meet the needs for both. At the core of our enclosed design is a partially-constrained, multi-piece polyurethane bushing with precisely-set preload. This architecture absorbs and disperses resonant engine frequencies as opposed to amplifying them (like some other designs do), which results in a positive-connection, enthusiast-feel mount with the vibration. Understanding that heat is a concern for the passenger side mount's close proximity to the exhaust, we utilize a PEEK thermal insulation plate to greatly reduce heat transfer to the polyurethane, making heat a non-issue for these mounts.
We offer two durometers, with both densities offering similar "positive connection" feeling. 60A is slightly softer and offers more of a stock feel, while 80A delivers a little more engine "feel" while under acceleration.
Product features and benefits:
This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335d 335i 335xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
Single piece 6061 construction, optimized cooling, provisions for temp sensor, and external cooler with removable air duct.
Built to last, made from a single piece of 6061 billet aluminum with a rugged and good-looking hard-coat anodizing the Turner diff cover can handle anything you throw at it. Not only is it an absolute masterpiece, but this billet diff cover checks all the boxes for features needed. Reinforced mounting ear for strength and stability. The mounting ear is unified with the one-piece billet cover and features added material for the highest durability possible. This diff cover is cool, literally, the entire construction was designed with optimized cooling in mind. External fins are strategically placed on the rear face, bottom, and between the mounting ears of the cover, serving as effective heat sinks for optimal heat dissipation. This ensures stable temperatures, promoting longevity for both the fluid and your differential. Additionally, the internal design ensures continuous oiling and lubrication of the ring gear, maintaining its stability and preventing fatigue by controlling heat more effectively. An internal baffle at the cover's corner helps maintain proper pressure and prevents cavitation.
All of the OEM features were retained along with the upgrades. The drain and fill plugs on the diff cover are upgraded to -6AN using the provided high-pressure fittings with replaceable o-rings. The drain and fill plugs can now be used for an external oil cooler allowing you to further expand the fluid capacity for optimized cooling and service intervals. To keep an eye on things from the driver seat is 1/8 NPT provision for temp sensors, this product from Turner has you covered at every turn.
Upgrading to our Turner Billet Differential cover gives you the strength you need to push your car to its limits without worrying about snapping a diff mount from clutch kicking or other shocks to the drivetrain. In addition to its enhanced strength, this differential cover includes numerous other upgrades and conveniences. These include improved cooling and lubrication for the ring gear, upgraded fill and drain plugs, and the option to expand an external oil cooler for extreme motorsport usage. Designed to complement both upgraded daily drivers and extensively modified track cars, it also offers a visually appealing design.
Key Benefits:
Reinforced mounting ear for strength and stability
16% Increased fluid capacity
External fins on the back side, bottom, and mounting ear on the casing for maximum cooling and consistent fluid temps
Removeable air duct to direct air across the cooling fins for even more temperature control
Optimized internal design to keep fluid consistently on the ring gear
Integrated breather to prevent cavitation by venting the appropriate amount of pressure being built up in the diff housing
-6AN ports to incorporate the use of a differential cooler - this increases capacity and lowers temps allowing for extended fluid change intervals
1/8 NPT fitting for the use of a temp sensor to monitor fluid temperature
Design:
Fits manual transmission Large Case 215mm differentials
Single piece 6061 Billet aluminum construction
T6 Black hard coat anodizing for superior corrosion resistance and aesthetics
Compatible with most differential coolers(-6AN) and temp sensors(1/8 NPT)
Designed to accommodate oversized rear sway bars
Retains OEM mounting features
Factory geometry bushing size for use with OEM and aftermarket poly bushings
Removeable air duct for easy access to sensors and drain/fill plug
All sets of 12 now 10% off regular price!
Red Line 75W140 is a full synthetic high-performance gear oil that is an excellent substitute for expensive factory fluid and an upgrade over off-the-shelf economy fluid. Red Line thoroughly evaluates the manufacturer's recommendations and only makes a fluid recommendation if their own product meets or exceeds the original specification. In many cases the Red Line synthetic will outperform the factory supplied fluids. We've been using Red Line Oil in our BMWs since we opened in 1994 and it remains our best selling BMW differential fluid. 75/140 is a specialized weight used for BMW M3, M5, and M6 models with the M Variable limited slip diff (all M models since 2001). Red Line fluid is used in nearly all E46 M3, E92 M3, E60 M5 we service as well as the custom differentials that we sell. It's great for the street where the polyol-ester base has natural lubricity and friction modifiers lead to smoother and quieter operation with lower operating temps than the factory fluid. We also use it in the track cars we build and prep. It may also be used in other specialized situations where a regular 75/90 will be too thin at elevated temperatures and your diff builder has approved a heavier weight oil.
Recommended for API GL-5, GL-6, MT-1, MIL-L-2105E, and SAE J2360. An alternative to the very expensive factory BMW SAF-XJ+FM diff fluid (#83222282583).
The Dinan short shifter provides shorter shift throws with a crisper and more precise feel than a stock shifter. Instead of retrofitting a stock BMW lever, with all of its deficiencies, Dinan has engineered this billet aluminum shifting system. Special features engineered into this unit include a two piece fully isolated stick assembly, exclusive integrated and dampened pivot cup with self lubricating pivot ball, counter balanced to reduce effort and exclusive polymer "Iglide" T-500 lower pivot bushings that are impervious to contamination. Featuring an adjustable pivot, which allows this shifter to fit both standard and M Series applications. All of this combined with a simple straightforward installation provides a professional level shifter. Provides a 30% throw reduction in E82 128i/135i, E9X 325i/328i/330i/335i, and E60 530i/545i/550i.
For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty.
Restore your BMW's shifter to its former precision with Turner Motorsport's top-notch replacement kit. Over time, most BMW shifters lose their original feel due to inferior rubber bushings. These bushings introduce excessive movement in the shift lever, resulting in a shifter that lacks precision.
Introducing Turner Motorsport's solution - a direct-fit, high-strength Teflon bushing. Meticulously crafted from pure Teflon rod, free from any impurities or fillers, these bushings promise extended durability. By eliminating side-to-side play in the shifter rod, they notably enhance the performance of even the stock shifter.
Elevate your BMW's shifting experience with Turner Motorsport's precision-designed replacement kit.
Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.
By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components.
Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.
By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components.
Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
Stock rubber flex discs allow for a slight amount of give, especially under heavy acceleration and, depending on the amount of force applied, could potentially tear or split. This slight flex/give can prevent instantaneous transfer of force to the wheels, making accelerations unpredictable, or even lead to your vehicle being stuck on the side of the track. To combat this, IRP's Performance Flex Disc was developed. Made of CNC machined aluminum, this flex disc won't actually flex, and the polyurethane bushings will only provide a enough give to dampen some vibrations and prevent damaging the transmission. This is perfect for high torque applications such a drag cars and dedicated track cars that want immediate response and long term reliability.
96mm Diameter
Fits the following BMWs:
2008+ E82 BMW 128i
5/1986-1991 E30 BMW 325e 325es M3 - Manual Transmission
1987-1991 E30 BMW 325ix - Between Transmission & Transfer Case
1996-1998 E36 BMW 328i 328is 328ic - Manual Transmission only
1999-2005 E46 BMW 323i 323ci 325i 325ci - Automatic & SMG Transmissions only
1999-2005 E46 BMW 328i 328ci 330i 330ci - Manual, Auto, and SMG
2006+ E90 BMW 325i 328i 330i - Manual or Automatic Transmission
2006+ E91 BMW 328i - Manual or Automatic Transmission
2007+ E92 BMW 328i - Manual or Automatic Transmission
2007+ E93 BMW 328 - Manual or Automatic Transmission
1982-1983 E28 BMW 528e - Manual Transmission
5/1986-1988 E28 BMW 528e - Manual Transmission
1982-1988 E28 BMW 533i 535i 535is M5 - Manual Transmission
1991-1995 E34 BMW 525i - Automatic Transmission
1989-6/1992 E34 BMW 525i - Manual Transmission
1993-1995 E34 BMW 530i - Manual or Automatic Transmission
1989-1993 E34 BMW 535i - Manual Transmission
2001-2003 E39 BMW 525i - Automatic Transmission
1997-2003 E39 BMW 528i 530i - Manual or Automatic Transmission
1980-1989 E24 BMW 633csi 635csi M6 - Manual Transmission
2000-2006 E53 BMW X5 3.0i - for Rear Driveshaft
2000-2003 E53 BMW X5 4.4i X5 4.6is - for Rear Driveshaft
2007-2013 E70 BMW X5 3.0si X5 4.8i X5 xDrive30i X5 xDrive48i - for Rear Driveshaft
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i - Automatic Transmission
1997-2002 Z3 BMW Z3 2.8 Z3 3.0i - Manual or Automatic Transmission
2003-2008 Z4 BMW Z4 2.5i - Automatic or SMG Transmission
2003-2008 Z4 BMW Z4 3.0i Z4 3.0si
Collapsing and worn engine mounts can mean big trouble for N52/N54/N55 cars. The stock mounts are filled with fluid that can leak or evaporate over time. That leaves the mount unstable and too flexible to properly support the engine. The side effects of a worn engine mount are: shaking and vibrating engine, driveline twist from engine torque that can break or snap bushings, and broken motor mount arms and bolts. If you're tired of replacing engine mounts you'll be very pleased wtih these solid rubber versions.
Not only are these more reliable than stock fluid-filled mounts, they are slightly stiffer than new stock mounts thanks to a solid rubber construction (no voids in the rubber) but designed for street use so they remain quiet and comfortable. The solid rubber has less deflection than a stock mount, so no wasted engine and transmission motion. Less wasted motion gives you more torque to the wheels (it's not spent twisting the engine) and better shifts.
Sold as a set of matching engine and transmission mounts.
This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335i 335xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
If there was a Top 5 list of things to do on the E46 M3, a shorter gears would be in the top two... The gearing used to be overlooked when planning modifications but the 3.91 and 4.10 gears are now one of our biggest selling upgrades for the E46 M3! With a rear end gear upgrade you get the effects of adding horsepower but without adding any more stress to the engine or drivetrain. The R&P acts as a torque multiplier, getting you into the power band sooner in each gear. It's one of the best areas to get return from your modification spending. The shorter (numerically higher) rear end gears will give you better acceleration in all gears at any speed with few downsides. Want to make your car faster off the line or out of corners? Or avoid a downshift to pass on the highway? This is what you need. This 4.10 is the latest version from BMW Motorsport - shot peened and hardend for increased strength. The R&P can be installed on its own but for cars that have more than 60,000 miles it would be a better idea to rebuild the whole diff. The factory viscous limited slip units have a typical lifespan of 50-70,000 miles. We offer diff rebuilding with 4.10 or other gear options and you get a fully-rebuilt and serviced limited slip unit at the same time. Click here for our diff rebuild options.
4.10 Gearing Example: 2004 M3, 6-speed manual, 275/35-19" rear tires
Gear RatioGearSpeedRPM
40 MPH in 4th
3.62 4th 40mph 2,250rpm
4.10 4th 40mph 2,550rpm
70 MPH Cruise
3.62 6th 70mph 2,650rpm
4.10 6th 70mph 3,000rpm
5th Gear Speed at Redline
3.62 5th 175mph 8,000rpm
4.10 5th 154mph 8,000rpm
Why 5th? Because 6th does not have the mechanical advantage to get past wind resistance at these speeds - it is more of a cruise/overdrive gear. Using 5th for comparison purposes is much more relevant than having to take into account wind direction, resistance, grade, elevation, tire sizing, etc. These numbers are for comparisons among gear ratios only, not to determine what your M3 will top out at.
This item is the genuine BMW part and the ring & pinion set only. You will need to have this professionally installed into your existing differential. BMW does not supply differential rebuild parts (bearings, shims, plates, etc.) so only a qualified shop that is experienced in BMW diff rebuilding should perform this installation. We also offer built differentials and exchanges, click here.
This item fits the following BMWs:
2001-2006 E46 BMW M3
2004-2010 E60 BMW M5 (manual transmission only)
OEM part number 33108321899
Shifter slop is a common complaint among all BMW models. Some of that play comes from the bushings where the shifter carrier mounts to the transmission. The original rubber carrier bushings don't last very long and when they get too soft the shifter flops around. These Delrin bushings have almost no deflection and will last much longer than the factory rubber, giving you precise shifting for many years.
Note: this is only one part of the shift linkage and there may be other components that need replacing to improve shifting feel.
New carrier bushing pins are included.
A sloppy shifter is one of the common complaints of older BMWs. In addition to the shifter linkage the transmission mounts contribute to rough and clunky shifting. BMW transmission mounts are rubber and get softer over time. This allows the transmission to dance around which changes the geometry of the shift linkage and could make it harder to shift. These urethane transmission bushings are stiffer than the stock rubber mounts and won't let the transmission shift around as much. The round design also has more surface area than the stock mounts which helps spread the load. Because the urethane is stiffer, expect more vibration to make its way into the shift lever area. Engine motor mounts should also be considered as a cause for driveline vibration, transmission movement, and poor shifting. Consider replacing your motor mounts at the same time as your tranny mounts.
Price is for the pair of transmission mounts with hardware.
This item fits the following BMWs:
1989-1995 E34 BMW 525i 530i 535i 540i M5
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1997-2003 E39 BMW 525i 528i 530i 540i M5
1999-2005 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci M3
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
Gaining a prominent edge over the competition is now within reach, thanks to the MFactory Helical Limited Slip Differential offered by Turner Motorsport. This Helical LSD ensures a seamless and uniform distribution of power to your BMW's wheels, significantly enhancing traction whether you're on the street, strip, or track. It's an absolute necessity for BMW enthusiasts.
Curious about the LSD's role? Without it, your car essentially operates as a one-wheel-drive machine, delivering torque solely to the wheel with less grip. This is where the Helical LSD shines, as it allows both wheels to receive power by limiting the speed difference between them, in contrast to the open differentials found in most vehicles.
Break-In Procedure: For optimal performance, it's recommended to change the fluid after the first 3-400 miles of use.
Please note that any defects or warranty claims should be directed to Team MFactory.
Achieve increased throttle response and acceleration with the MFactory range of single-piece Lightweight Flywheels!
Diamond Cut to exacting tolerances from Forged Chromium-Molybdenum Steel
Perfect fitment & finish ensures hassle-free installation
Designed using leading-edge Solidworks 3D CAD & Cosmos FEA software
Advanced Geometry minimizes parasitic drivetrain losses. Race transmissions built with MFactory components transfer, on average, 1-2% more power to the ground over our competitors!
Precision Balanced to over 12000rpm
Ensures the utmost reliability from our Lightweight Flywheels, which are specifically designed to reduce weight and inertia for improved engine response and acceleration
Specifications
Made from imported Japanese SAE 4140 Steel
Forged, Double Tempered and Super Sub-Zero treated for unsurpassed toughness
Proprietary Nitride surface treatment for increased surface hardness
The ECS Tuning Center Support Bearing Brace is engineered to improve drivetrain performance and longevity. The factory center support bearing features internal an internal rubber bushing to reduce NVH (noise, vibration, and harshness) transmission to the cabin. Unfortunately, this material choice falls short when it comes to performance applications. Under extreme load conditions, this bushing is prone to flexing, resulting in driveshaft misalignment. To address the shortcomings of the factory rubber center support carrier design, ECS engineers developed a set of precision-fit, split polyurethane bushings that secure tightly around the existing driveshaft bearing. Constructed from 90A durometer polyurethane, this material eliminates bushing deflection while maintaining minimal noise, vibration, and harshness (NVH). By eliminating deflection, this innovative solution not only improves durability but also ensures a significantly longer service life than the OEM center support bearing—making it an excellent upgrade for aging BMW chassis.
The polyurethane bushings are surrounded by a robust 6061-T6 billet aluminum bracket designed with strength and reliability in-mind. This bracket features a split design for hassle-free installation, eliminating the need to remove the driveshaft assembly entirely. To install the ECS Center Support Carrier, simply cut around your existing bearing, remove the factory brace, and clamp on your new bushings and bracket. This user-friendly approach saves time and simplifies maintenance or upgrades. Two stainless steel socket head screws are used to fasten the two-piece bracket, offering corrosion resistance and secure clamping under high torque and stress. This combination of materials and design ensures dependable performance and long-lasting durability, even in demanding applications.
Features & Benefits:
Performance-Designed Bushing Upgrade: 90A durometer polyurethane is used to eliminate bushing deflection while maintaining a smooth, quiet ride. Improved Longevity: Polyurethane construction offers a longer lifespan than factory rubber, ideal for enthusiasts looking to eliminate future CSB-related problems. Billet Aluminum Bracket: The upgraded bushings are encased in a 6061-T6 billet aluminum bracket for enhanced durability and improved performance. Easy Installation: Both the bushings and the bracket feature a two-piece split design, allowing for seamless installation without driveshaft removal. Reduce Deflection, Increase Rigidity: Designed with performance in mind, this upgrade eliminates excessive driveshaft movement for improved alignment and efficiency. Kit Includes:
ECS Driveshaft Center Support Bushings ECS Driveshaft Center Support Carrier (2) Stainless Steel Hex Head Screws (2) Flange Nuts (26117574872) Medium Strength Threadlocker (0.5ml) Installation Instructions:
ECS has provided a detailed, start-to-finish installation guide to aid in the process of installing your new Driveshaft Center Support Carrier.
The stock center support bearing carrier is engineered to minimize noise, vibration, and harshness (NVH) in the cabin by loosely securing the center bearing with a soft rubber bushing. However, this design allows the driveshaft to move off-center during launches and shifts, reducing throttle response and causing drivetrain oscillations. Over time, the rubber bushing can sag or dry rot, leading to misalignment of the driveshaft.
Prevent or fix this common problem with JXB Performance's Driveshaft Center Support Bearing Upgrade! This upgrade features a simple yet highly effective 2-piece design that makes installation and bushing replacement effortless. The stock carrier is cut away, and the JXB bushings securely "clamp" the driveshaft bearing in place, ensuring constant driveshaft alignment.
The Street bushing option from JXB is the most popular choice, offering a significant improvement over the stock design while keeping NVH levels minimal.
Note: Some light NVH, such as a soft hum, may occur at certain speeds. However, with a modified exhaust or open windows, it’s unlikely to be noticeable.
Installation is straightforward and doesn’t require removing the driveshaft. The 2-piece design clamps directly onto the OEM bearing, though removing the old carrier will require a cutting tool.
Need replacement or additional bushings? See T#4799658 for replacement street bushings.