BMW Drivetrain Parts for BMW 3 Series E92 (2007-2013)

If there was a Top 5 list of things to do on the E46 M3, a shorter gears would be in the top two... The gearing used to be overlooked when planning modifications but the 3.91 and 4.10 gears are now one of our biggest selling upgrades for the E46 M3! With a rear end gear upgrade you get the effects of adding horsepower but without adding any more stress to the engine or drivetrain. The R&P acts as a torque multiplier, getting you into the power band sooner in each gear. It's one of the best areas to get return from your modification spending. The shorter (numerically higher) rear end gears will give you better acceleration in all gears at any speed with few downsides. Want to make your car faster off the line or out of corners? Or avoid a downshift to pass on the highway? This is what you need. This 4.10 is the latest version from BMW Motorsport - shot peened and hardend for increased strength. The R&P can be installed on its own but for cars that have more than 60,000 miles it would be a better idea to rebuild the whole diff. The factory viscous limited slip units have a typical lifespan of 50-70,000 miles. We offer diff rebuilding with 4.10 or other gear options and you get a fully-rebuilt and serviced limited slip unit at the same time. Click here for our diff rebuild options.

4.10 Gearing Example: 2004 M3, 6-speed manual, 275/35-19" rear tires

Gear RatioGearSpeedRPM

40 MPH in 4th
3.62 4th 40mph 2,250rpm
4.10 4th 40mph 2,550rpm

70 MPH Cruise
3.62 6th 70mph 2,650rpm
4.10 6th 70mph 3,000rpm

5th Gear Speed at Redline
3.62 5th 175mph 8,000rpm
4.10 5th 154mph 8,000rpm 

Why 5th? Because 6th does not have the mechanical advantage to get past wind resistance at these speeds - it is more of a cruise/overdrive gear. Using 5th for comparison purposes is much more relevant than having to take into account wind direction, resistance, grade, elevation, tire sizing, etc. These numbers are for comparisons among gear ratios only, not to determine what your M3 will top out at.

This item is the genuine BMW part and the ring & pinion set only. You will need to have this professionally installed into your existing differential. BMW does not supply differential rebuild parts (bearings, shims, plates, etc.) so only a qualified shop that is experienced in BMW diff rebuilding should perform this installation. We also offer built differentials and exchanges, click here.

This item fits the following BMWs:
2001-2006 E46 BMW M3
2004-2010 E60 BMW M5 (manual transmission only)

OEM part number 33108321899

Collapsing and worn engine mounts can mean big trouble for N52/N54/N55 cars. The stock mounts are filled with fluid that can leak or evaporate over time. That leaves the mount unstable and too flexible to properly support the engine. The side effects of a worn engine mount are: shaking and vibrating engine, driveline twist from engine torque that can break or snap bushings, and broken motor mount arms and bolts. This is a Genuine BMW replacement. When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335i 335xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

A sloppy shifter can make your driving experience miserable. Luckily these Genuine BMW shifter rebuild kits are available to restore the crisp feel of a brand new shifter. This kit includes all of the Genuine BMW components that normally wear down and cause issues such as the bushings, clips, and dowel pin.

See all of the included components below!

This is the stock twin mass flywheel for the N55 engine used in the E82 135i, E9X 335, F3x 335/435, and F10 535i. It's manufactured by OEM supplier LuK. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

This item fits the following BMWs with the single turbo N55 engine and manual transmission:
2011-2012 E82 BMW 135i
2011 E90 BMW 335i 335xi 335i xDrive - Sedan
2011-2013 E92 BMW 335i 335xi 335i xDrive - Coupe
2011-2013 E93 BMW 335i - Convertible
2012-2015 F30 BMW 335i 335iX - Sedan
2014-2016 F34 BMW 335iX - Gran Turismo
2014-2016 F32 BMW 435i 435iX - Coupe
2014-2016 F33 BMW 435i 435iX - Convertible
2014-2016 F36 BMW 435i 435iX - Gran Coupe
2011+ F10 BMW 535i 535i xDrive