BMW Intake Parts for BMW 3 Series E92 (2007-2013)

Replacement stock air filter element for the stock BMW air box of the 2006+ E90/E91/E92/E93 3 Series 325i, 330i, 328i & 328xi.

This air filter fits the following BMWs:
2006 E90 3 Series Sedan - 325i, 325xi, 330i & 330xi
2007+ E90 3 Series Sedan - 328i & 328xi
2007+ E92 3 Series Coupe - 328i & 328xi

Upgrade your BMW N52-powered vehicle with the high-performance E90 330i 3-stage intake manifold. Compared to other N52-powered models, the 330i boasts the highest horsepower due to its 3-stage manifold design. This manifold features two DISA valves that optimize air diversion to the cylinders, maximizing power extraction from the engine.

Key benefits of the 3-stage manifold include:

• Efficient air distribution to cylinders for enhanced power output.
• Improved fuel adjustments by the ECU for optimal performance.
• Bolts onto any N52 version and, with an ECU flash, can add up to 42hp.

The kit includes:

• 330i intake manifold
• Both DISA valves
• Gaskets

For additional power gains, consider purchasing the N52 Euro Air box (ES#2072577) alongside this manifold. Please note that an ECU reflash is necessary for proper functionality of the intake.

Enhance your N52 engine's performance and power output with this comprehensive E90 330i 3-stage intake manifold kit.

If you are looking to replace your stock chargepipe for better reliability and higher performance, the Burger Motorsports designed and Phoenix Racing built Performance Aluminum Chargepipe is an excellent choice! This aluminum chargepipe is significantly stronger than the stock plastic pipe and the powder coated aluminum looks great and will resist any corrosion. Plus, this chargepipe features a 3 inch design for optimal flow at all RPMs, prevent restriction that would normally be seen with the stock pipe. This is perfect for someone looking to upgrade a stock or tuned N54!

Specs and Features:

• Aluminum Construction
• Black Powder Coating
• 3" Diameter
• CNC Machined Throttle Body Flange
• Dual 1/8" NPT Bungs
• High Pressure T-Bolt Clamps
• All Required Installation Hardware

O-rings and retaining clip must be reused from the original pipe or purchased new for proper installation.

If you are looking to replace your stock chargepipe for better reliability and higher performance, the Burger Motorsports designed and Phoenix Racing built Performance Aluminum Chargepipe is an excellent choice! This aluminum chargepipe is significantly stronger than the stock plastic pipe and the powder coated aluminum looks great and will resist any corrosion. Plus, this chargepipe features a 3 inch design for optimal flow at all RPMs, prevent restriction that would normally be seen with the stock pipe.

In addition, this pipe also includes a Tial BOV flange for easy installation of a Tial BOV without any modifications needed to the chargepipe. This is perfect for someone looking to upgrade a tuned or heavily modified N54!

Specs and Features:

• Aluminum Construction
• Black Powder Coating
• 3" Diameter
• Tial BOV Flange
• CNC Machined Throttle Body Flange
• Dual 1/8" NPT Bungs
• High Pressure T-Bolt Clamps
• All Required Installation Hardware

O-rings and retaining clip must be reused from the original pipe or purchased new for proper installation.

Unleash the roar of your N52 engine with the Turner Motorsport E9x N52 Muffler & Resonator Delete Kit. Elevate your driving experience by transforming your exhaust with this cost-effective kit, providing performance gains, a captivating exhaust note, and stunning exhaust tips. Shedding the heavy factory muffler, Turner's T304 stainless steel 3.0" tubing replaces it, delivering a lighter, high-flow solution compatible with the OEM rear valance. Easy to install with hand tools, this muffler delete adds a powerful sound without significant drone, while shaving off about 20lbs from your vehicle. Upgrade your N52 without replacing the entire exhaust system!

Key Features:

• Turner designed Muffler & Resonator Delete for N52 engine
• T304 stainless steel construction with 1.25mm wall thickness
• CNC mandrel-bent 3.0" tubing for optimal exhaust gas routing
• Tig-welded exhaust hangers for direct fitment
• Hand-Tig welded joints for durability
• Stainless steel Accuseal exhaust clamps for a leak-proof seal
• Large radius bends ensure smooth transitions for optimal flow

Kit Includes:

• Y-pipe section
• Tailpipe section
• Dual 3.0" exhaust tips (Black Chrome finish)
• Stainless steel Accuseal exhaust clamps

See and hear the difference on the ECS YouTube page.

The factory plastic gears in BMW S65 throttle body actuators are notorious for premature wear due to mechanical stress, engine vibration, and heat cycling. Over time, this wear leads to excessive play, throttle response issues, and eventual failure. This can cause DME fault codes, limp mode, and DSC malfunctions. While replacing both throttle actuators is costly, even new OEM units will eventually suffer the same fate.

Thankfully, ECS has developed the ultimate solution for E9X M3 owners! These Upgraded Throttle Body Actuator Gears are constructed of Teflon-reinforced nylon, significantly reducing friction and gear tooth wear for long-term reliability. Each gear comes pre-installed on a 4140 steel shaft, strengthening the assembly and preventing further failure.

Servicing the internals of S65 throttle body actuators can be a challenging task due to their intricate design. To simplify the process, ECS has developed a complete plug-and-play replacement kit. This kit includes two brand-new OEM Continental/VDO throttle body actuator assemblies, rebuilt with upgraded ECS gears and shafts for simplified installation and long-term durability. Unlike rebuilt actuators, this solution minimizes the risk of internal electrical failures, providing superior protection against common failure modes.

Features & Benefits:

Upgraded Teflon-reinforced nylon gears – Superior to factory plastic-on-plastic gears, reducing wear and extending lifespan. 4140 steel shafts – Increases durability and simplifies installation. Pre-installed inside OEM Actuators – Decreases install complexity and reduces the risk of electrical failure in rebuild units. Prevents common actuator failures – Resolves worn gear issues that cause CELs, limp mode, and DSC/DME errors. Cost-effective alternative to full actuator replacement – Saves hundreds in parts and labor. Factory-like fitment – Engineered for precise compatibility and long-term reliability. Built to withstand heat and mechanical stress – Ensures consistent throttle performance and extended service life.

Airflow efficiency and maximizing the potential of the stock intake design were the keys to development for the Dinan S65 intake. Dinan improves on the factory air box system by using a larger K&N filter combined with a precision molded carbon fiber intake tube. The increased amount of air feeds the engine and elicits a slightly more audible and sporty tone over its stock counterpart. Dinan claims 8hp and 5ft-lb torque gain with this kit.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. This intake is worth 3 points toward your Dinan badge.

Fitment note: Convertible models require modification to a factory chassis brace. Detailed instructions are included.

*NOT CARB APPROVED 

This item fits the following BMWs:
2008-2013 E90 E92 E93 BMW M3 Sedan, Coupe, Convertible