Athena Cut Ring Head Gasket - 84.5mm - BMW M50 M52 (84mm Bore) ...

T#:26171655

Part#: ATH-HG-CR-M50-84

In Stock

$ 324.99 USD

Add to Wish List

Qty

$ 324.99 USD

Add to Wish List

Upgrade your BMW engine's performance with the Athena Cut Ring Head Gasket. This gasket replaces BMW part # 11121726619 and 11121726617 and is specifically designed for M50 & M52 iron block inline 6-cylinder engines found in E34/E36 chassis. Standard OEM & MLS gaskets can only handle a certain amount of cylinder pressure before they start to leak, making the Athena Cut Ring Head Gasket the recommended choice for applications making 16+ psi. A compression leak passing the head gasket can cause a range of issues, including engine overheating, loss of power, misfires, and in severe cases, catastrophic engine failure. Athena's gasket is crafted with premium quality reinforced M0115, an asbestos-free material that's original equipment approved and renowned for its superior quality. The AISI 304 stainless steel Cooper Rings bite into the aluminum head, providing maximum sealing capabilities around the cylinder bore and optimizing engine performance, even on engines with nitrous and/or turbo applications that exceed 2-bar boost. Before installation, it is crucial to have the mating surfaces of the cylinder head and block professionally cleaned and resurfaced to ensure they are completely flat. Please be aware that the gasket should have a size that is 0.5mm to 1mm larger than the piston. For example, if the piston measures 84mm, then the gasket should be the next size up, either 84.5mm or 85mm. Installation instructions: Make sure that the engine block and cylinder head surfaces are clean, flat, and free from any debris, oil, or coolant. Install the Cut Ring gasket on the engine block and ensure that it is properly aligned. Avoid twisting or bending the gasket during installation. Place the cylinder head on top of the gasket and install the head bolts or studs in their correct positions. Follow the manufacturer's recommended torque specifications and tighten the bolts or studs in the proper sequence to ensure even clamping force across the gasket. After the initial tightening, re-torque the head bolts or studs after the engine has been started and then allowed to cool to room temperature. This will ensure that the gasket is properly seated and compressed. It is recommended to not use any additional sealant on the MLS gasket, as it is already coated with a Viton rubber sealant. Using additional sealant can hinder the performance of the gasket.

Show More Show Less

BMW N54 ARP Head Stud Kit

T#:17538610

Part#: ARP-HSK-N54-14

In Stock

$ 599.99 USD

Add to Wish List

Qty

$ 599.99 USD

Add to Wish List

The VAC Motorsports ARP Head Stud Kit was put together by VAC and ARP’s finest engineers. This is a completely custom kit designed specifically for the almighty N54. *High Boost (25+ psi application) option features: (14) 11mm ARP Head Studs (14) ARP Washers for 11mm Studs (14) ARP Nuts for 11mm Studs Install Tips: MUST drill and tap the (4) 9mm holes in the engine block to make them 11mm holes. This way all the engine block holes are 11mm, and fit ALL (14) 11mm Studs. Torque Specs: All studs torque down through 3-equal steps to 95 ft lbs ***This is NOT the Chrysler and Volvo stud kits! VAC Motorsports and ARP engineers designed and assembled this kit with high grade material, specifically so standard street-use or high-boost N54 owners have a PROPER kit that does not fail over time, such as the retro-fit Chrysler and Volvo head stud kits. ARP is the world leader in fastener technology. Makers of the finest fasteners in the market, especially for BMW engines, ARP is the brand you can count on when you want the highest reliability possible. If you are looking for high performance from your BMW engine, then ARP Head Stud Kits are a must. All kits come complete with hardened parallel-ground washers and aerospace-quality nuts.

Show More Show Less

R56 Main Stud Kit

T#:30397432

Part#: R56MSK

Ships in 3 Business Days

$ 159.99 USD

Add to Wish List

Qty

$ 159.99 USD

Add to Wish List

ARP Performance Head Stud Kit - N54

T#:1061441

Part#: ARP-HSK-N54

Ships in 4 Business Days

$ 554.99 USD

Add to Wish List

Qty

$ 554.99 USD

Add to Wish List

Despite the fact that BMW engineers some of the worlds most revered engines, during number crunching something always has to be a compromise. One item that is always found to be a weak point- the OEM hardware. It is definitely sub-par for real performance use under high stress such as modded engines and track use. We use these fasteners on all of VAC's in-house head builds. Whenever the head is coming off, your switching to forced induction, or if you are simply prepping to drive your car hard; we highly recommend switching to far superior race-grade hardware. These Head Stud Kits greatly improve reliability; helping to eliminate movement of the of the cylinder head and intern, gasket failure caused by inferior OEM head-bolt stretch. This is the #1 cause of premature head gasket failure, especially on boosted or high output engines. Though more expensive than OEM, converting to one of VAC's head studs kits will not only give added strength and reliability when its needed most, but provides the most accurate torque readings because studs don’t “twist” into the block; all clamping forces are on one axis, and there is less force exerted on the normally stressed threads of the block. This increases block and hardware life and typically makes the head easier to properly install to the block, a blessing if your head may have to be removed more than once. Especially in the time crunch of racing, when engines are dissembled frequently, studs make removing and installing the cylinder head on to the block a much easier task. By allowing the studs to act as a guide on to the head, your head slides on and off and also ensures proper alignment of the head and gasket for the same reason. It is similar to converting your wheel-bolts to wheel-studs.

Show More Show Less

ARP Head Stud Kit - BMW N55/S55

T#:23416542

Part#: ARP-HSK-S56-CA

In Stock

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

BMW S58 3.0L ARP Head Stud Kit - CA625+

T#:22427036

Part#: ARP-HSK-S58-CA

Ships in 4 Business Days

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

BMW S58 3.0L ARP Head Stud Kit - CA625+ is the ultimate upgrade for the BMW S58 engine, specifically designed for high-performance models such as the F97 X3M, F98 X4M, G80 M3, G82 M4, G83 M4, and G87 M2. Manufactured by Turner Motorsport, this head stud kit ensures optimal engine reliability and performance.

Enhanced Strength: Featuring Custom Age 625+ material with a tensile strength of 260 ksi, this kit provides superior strength compared to factory bolts.
Prevents Head and Block Separation: Designed to handle increased boost levels and high-stress conditions, preventing potential head and block separation.
Precision Engineering: ARP’s advanced manufacturing process ensures that these head studs outperform standard factory bolts under extreme conditions.
Ideal for High-Performance Builds: Perfect for enthusiasts pushing the limits of their S58 engines, offering unparalleled durability and reliability.
Direct Fit: Specifically tailored for the turbocharged inline 6-cylinder BMW S58 engine, ensuring a seamless installation and optimal performance.

Show More Show Less

ARP Rod Bolt Set - M20 - 53mm

T#:1061435

Part#: ARP-RBS-M20

Ships on Aug 4, 2026

$ 314.99 USD

Add to Wish List

Qty

$ 314.99 USD

Add to Wish List

ARP, the world’s leader in fastener technology. There is no substitute for the best! Planning to boost your M20? Building a high HP stroker engine? This rod bolt kit is for you! This kit provides higher strength, more clamping power, and the option to re-use the hardware unlike your OEM bolts. We run these in many of our own builds as well and are 110% satisfied with the fit and finish of these ARP bolts. We offer a 53mm UHL version for those running OEM M20 rods or a 44mm UHL version for those who have upgraded to S50/S52 OEM rods.

Show More Show Less

MINI R55+ Sneed4Speed N Series Engine Cylinder Head Bolts Kit ...

T#:18965470

Part#: NSHBS

In Stock

$ 74.99 USD

Add to Wish List

Qty

$ 74.99 USD

Add to Wish List

MINI R55+ Sneed4Speed N Series Engine Cylinder Head Bolts Kit

Upgrade your MINI's engine with the MINI R55+ Sneed4Speed N Series Engine Cylinder Head Bolts Kit. Engineered for performance and durability, this kit includes high-quality cylinder head bolts designed specifically for N series engines. Ensure a secure and reliable seal for your cylinder head with this premium bolt kit from Sneed4Speed.