Flywheels

The factory BMW S55 dual-mass flywheel is engineered with comfort in mind, catering to the luxury-oriented expectations of the brand’s driving experience. Its design focuses on dampening drivetrain vibrations, smoothing out gear transitions, and minimizing harshness during operation. However, this refinement costs valuable performance. The dual-mass flywheel adds a substantial 26.5 lbs of rotational mass to the drivetrain, which significantly hinders throttle response and makes rev-matching feel sluggish and disconnected. Moreover, dual-mass flywheels are notorious for being a weak link in modified or high-performance builds and can prove costly to replace when they inevitably fail.

Our Single-Mass Lightweight Flywheel Conversion addresses all of these shortcomings with a purpose-built, lightweight, single-mass design that prioritizes performance. Weighing in at only 18.5 lbs., this design significantly reduces rotational mass, allowing your S55 to achieve its true motorsport potential!

Features & Benefits:

Precision machined from 4140 HT heat-treated chromoly steel for exceptional toughness, even wear properties, and increased durability.
Material quality promotes even wear across the entire friction surface, prolonging component lifespan.
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability.
Hardness improves component wear characteristics.
Black oxide coated for corrosion resistance on non-friction surfaces.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 certified to ensure safe operation under extreme operating conditions.
Specifically designed to work with S55 OE-architecture clutches.
Optimized step height maximizes clutch clamp load and offers a prolonged service life.
Performance:

10 lbs. lighter than the factory BMW flywheel!
OEM Dual-Mass: 26.5 lbs.
Turner Motorsport Single-Mass: 18.5 lbs.
Faster revs
Improved throttle response and acceleration
Allows for a more engaging driving experience and delivers a feeling of direct connection
Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

Engineered in-house, we designed this lightweight, single-mass flywheel to provide more than 10 pounds of weight savings over the factory flywheel. While some ultra-lightweight performance flywheels are manufactured from aluminum, our designers opted for a more driveable experience with steel. The mass provided by steel helps dampen vibrations and noise, delivering near-factory refinement with most of the benefits of a lightweight flywheel: quicker throttle response, improved durability (and longevity), and more effective transfer of power to the wheels.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

When it comes to selecting a clutch to pair with a lightweight flywheel, consider the driving you’ll be doing. As a single mass flywheel eliminates the dual-mass dampening of the factory flywheel, to retain the lowest noise, lowest harshness driving experience possible, select a clutch with a dampened disc such as the ACT Heavy Duty. For dedicated track cars, a solid clutch hub is appropriate.

Our recommendations:

Street: ACT Heavy Duty
Track: ACT Xtreme for high torque cars or OE 335is LuK (with 440lbs-ft or less)
Features:

Precision machined from 4140 HT heat treated chromoly steel for exceptional toughness, even wear properties, and durability.
Material quality promotes even wear across the entire friction surface
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability and elevated temperatures
Hardness improves wear characteristics
Black oxide coated for corrosion resistance on non-friction surfaces.
8620 steel pilot bearing pin, case hardened and Precision ground for maximum wear resistance.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 tested and certified to ensure safe operation under extreme operating conditions
SFI 1.1 specifies minimum material properties and requires a 3rd party lab certification test, spinning the flywheel to 1.5x redline for 1 hour to ensure the flywheel will not burst.
Specifically designed to work with N54 architecture clutches
Step height designed to optimize clamp load and maximize the usable range of clutch wear for a long service life
Performance:

Turner Flywheel 18.6 lbs
10 lbs lighter than the factory BMW flywheel (Stock Flywheel 28.9 lbs)
Faster revs
Improved throttle response
Improved acceleration
Sportier driving experience
Stock flywheel weight - 28.9lbs
Turner single mass flywheel weight = 18.55lbs

Single Mass Flywheel Conversion:

Audible chatter from the transmission after installation is considered normal. As with most single mass flywheels, there is less dampening in the flywheel to reduce "gear noise." This chatter noise may be more present when the transmission fluid temperatures are hotter and may be intensified by other modifications. Most gearboxes will experience some chatter noise at hotter temperatures. Please be advised that this noise will disappear once the clutch pedal is depressed. This symptom may be lessened by adjusting transmission fluid weight, turning off electrical/driveline consumers (A/C, High Beams, ETC.), and by raising the RPM slightly.

Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

This item fits the following BMWs with 8 bolt flywheel and build date up to 01/2009 or earlier:
2008-01/2009 E82 BMW 135i 135is 1M
2007-01/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-01/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-01/2009 E93 BMW 335i - Convertible
2008-01/2009 E60 BMW 535i 535xi 535i xDrive

Lightweight flywheels have proven themselves to be a worthwhile performance enhancement. But with the quicker throttle response and horsepower improvement comes one serious drawback: flywheel chatter. Without the dual-mass flywheel's rubber isolators, a lightweight aluminum flywheel has more rattle than stock. ECS has designed this flywheel using chrom-moly steel and it weighs almost ten pounds less than the stock DMF but not as extreme as full aluminum flywheels. The steel helps dampen vibration and noise so you get near-factory refinement and most of the benefits of a lightweight flywheel: quicker throttle response, better reliability, and more power to the wheels. Zero-balanced and SFI 1.1 certified (material and design has been independently burst tested to ensure quality and safety). This flywheel requires the E34 M5 sprung hub clutch kit. Choose below from the flywheel only or a complete kit.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

Stock flywheel weight - 25.0lbs
ECS flywheel weight = 16.55lbs

This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed) 

The factory dual-mass flywheel in your MINI N14 was built with comfort in mind—absorbing drivetrain vibrations and smoothing shifts—but at the cost of performance. Weighing in at a hefty 28.3 lbs., the OEM flywheel adds excessive rotational mass, dulling throttle response, slowing acceleration, and complicating precise rev-matching. Worse yet, it's known to be unreliable in modified or tuned setups and expensive to replace when it fails.

This single-mass design from ECS Tuning weighs just 18.8 lbs. It cuts nearly 10 lbs. of rotational weight to significantly enhance throttle response, acceleration, and overall driving feel. Built for durability and spirited driving, it's the ultimate upgrade for enthusiasts who want to make the most of every gear change.

Key Features:

Precision CNC-machined from 4140 HT Chromoly Steel: Ensures outstanding toughness, consistent wear, and long-term durability.

Heat Treated and Tempered: Achieves HRC 28-32 for improved strength, stress relief, and dimensional stability—even at elevated temperatures.

Black Oxide Coated: Resists corrosion for long-lasting protection and a professional finish.

Precision Balanced: Exceeds OEM standards (G16, 175 g-mm) to ensure smooth, safe operation at all RPMs.

SFI 1.1 Certified: Tested and approved for extreme use—track or street.

Direct Fit for OE N14 Clutch Kits: Maintains compatibility with factory-style components for hassle-free installation.

Performance Benefits:

Substantial Weight Reduction

​OEM Flywheel: 28.3 lbs.

ECS Lightweight Flywheel: 18.8 lbs.

Net Savings: Nearly 10 lbs.

Faster Revving and Sharper Throttle Response: Reducing rotational mass translates into a more dynamic and responsive driving experience.

Improved Clutch Engagement and Longevity: Optimized step height delivers better clamp load and extends service life.

Ideal for Modified MINIs: Built to handle increased power and spirited driving with confidence.

Replaces MINI OEM Part #: 21207575069

The factory dual-mass flywheel in W11-powered MINI Coopers was designed with comfort in mind—minimizing drivetrain vibration and delivering smoother shifts. However, this focus on refinement comes at a performance cost. The hefty 27 lbs. of rotational mass dulls throttle response, slows acceleration, and makes rev-matching more difficult. Dual-mass flywheels are also known to be less reliable in tuned or modified setups and can be expensive to replace when they fail.

ECS Tuning developed their Lightweight Single-Mass Flywheel to address these issues with a performance-focused alternative. Weighing in at just 17 lbs., this flywheel sheds nearly 10 lbs. of rotating mass compared to the OEM unit—transforming throttle response, acceleration, and clutch feel for a more engaging and dynamic driving experience.

Key Features:

Manufactured from 4140 Chromoly Steel
Heat-treated and tempered for exceptional strength, wear resistance, and thermal stability.
Optimized Hardness (HRC 28–32)
Ensures consistent performance and durability under extreme conditions.
Precision-Balanced to G16 Standard (175 g-mm)
Exceeds OEM balance requirements for smooth, high-RPM operation.
Black Oxide Finish
Provides effective corrosion resistance and a sleek appearance.
SFI 1.1 Certified
Validated for safe use in high-performance and racing environments.
Direct Fit
Engineered to work seamlessly with OE-style clutch kits designed for the W11 engine architecture.
Performance Benefits:

OEM Flywheel Weight: 27 lbs
ECS Lightweight Flywheel Weight: 17 lbs
This significant weight reduction results in:

Sharper throttle response
Faster engine revs and acceleration
Improved clutch engagement and feel
Increased performance potential for modified vehicles
OEM & Aftermarket Compatibility:

Replaces OE Flywheel #: 21207532057
Compatible Clutch Kits:
MINI OE: 21207551384
Spec: SB001, SB003
Clutch Masters: 03050HD00R
Recommended Hardware:

Flywheel Bolts: 11227560579 (Qty 8)
Pressure Plate Bolts: 21207520449 (Qty 6)