BMW Suspension Parts

Improve your BMW's driving experience by addressing the wear and tear caused by years on the road. The suspension takes a beating from pot holes, speed bumps, and road hazards, leading to a weakened and sloppy feel. Enhance safety and ride comfort by replacing worn components, such as the control arm.

• Improved driving experience and ride comfort
• Enhanced safety through the replacement of worn suspension components
• Non-serviceable ball joints and other components addressed for prolonged lifespan
• Control arm replacement for a better feel and handling
• Recommended replacement in pairs for optimal performance
• Suitable for both front and rear suspension upgrades
• Referred to as a wishbone by BMW
• Performance upgrade for non-M3 models, recommended to replace in pairs due to heavy-duty nature

Enhance your driving experience with our premium suspension upgrade for your BMW. Over time, the road can take a toll on your suspension, leading to a sloppy and weak feel while driving. Our solution? Replace the control arm – a critical component that, after years of service, may wear out. Boost safety and ride comfort with this easy upgrade.

• Improved driving experience
• Enhanced safety
• Better ride comfort
• Extended service life of replacement parts

If you're considering replacing any part of your front or rear suspension, opt for doing it in pairs (both left and right sides). This ensures optimal performance and longevity of the replacement parts. In the BMW world, it's often referred to as a wishbone.

For non-M3 models, this isn't just a replacement – it's a performance upgrade. These heavy-duty components are recommended to be replaced in pairs to maximize their efficiency and provide a seamless driving experience.

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

• 100% machined and anodized, 6061-T6 lightweight aluminum arms
• High-strength, 3-piece, rod end (with carbon fiber reinforced, PTFE race) offers longer life for street compared to standard rod ends
• SEALS-IT Rod end seals keep dirt, water, and other contaminants out
• Rod ends feature grease fittings, to allow for rod end serviceability.
• Lighter than stock!  (Stock is 875g, RE arms are 640g)
• Extremely easy installation and adjustment (your alignment shop will LOVE you!)

Updated design!  Now shipping!

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

100% machined and anodized, 6061-T6 lightweight aluminum arms (and collars).

Stainless hardware and spacers are perfect for the tough Northeast climate!

New!  Easy adjustment with 22mm open ended wrench and 5mm allen key!  It only requires 15 ft. lbs. on the clamp to secure the clamp!

New!  Included lock-out kit, replaces factory eccentric hardware.

Updated 3-piece rod ends features 4130 chromoly steel bodies, heat-treated, alloy steel races, and Teflon liners

Extremely easy installation and adjustment (your alignment shop will LOVE you!)