11428583895KT - Genuine BMW Oil Filter Housing Replacement Kit - BMW F22/23 F3X B58 3.0L
Genuine BMW Oil Filter Housing Replacement Kit - BMW F22/23 F3X B58 3.0L
BMW's B58 engine has been very successful and has proved to be a reliable powerplant that is highly capable of producing some crazy power figures. Unfortunately, in true BMW fashion, the B58 engine does have a few problems that can become serious issues if not addressed quickly.
One of these issues is the oil filter housing cracking and leaking engine oil and/or coolant. BMW chose to construct the oil filter housing out of plastic and the housing tends to split if the cap is tightened too tight or even just over time as the plastic becomes brittle from numerous heat cycles. Another common failure point is the multiple gaskets that seal the housing to the engine block and between the housing and the engine oil cooler. when these seals fail, you will notice coolant and/or oil loss, or even the mixing of engine oil with coolant. There is also the possibility of your oil filter collapsing inside of the filter housing and preventing proper oil filtration and flow, sometimes clogging the small oil channels in your filter housing as the oil filter begins to fall apart. Though this is more common with vehicles that see extended oil change intervals, such as 12K+ mile oil changes, we have seen some failures as soon as 5,000 miles after an oil change!
Whatever the cause may be, the solution is almost always the same, replacement of the whole oil filter housing. We have put together a kit including the basic components needed to replace your oil filter housing and get your BMW back on the road!
Included:
Genuine BMW Engine Oil Filter Housing - Includes a new cap, seals, and oil filter (oil cooler not included and must be reused or purchased new - see BMW # 11428583901)
Oil Cooler Mounting Hardware
Oil Drain Plug Gasket
Intake Manifold Gaskets
Throttle Body Gasket
Transmission Fill Plug (For Automatic models)
Genuine BMW Installation Hardware
Not included in this kit are the fluids that will need to be replaced or topped off after the installation of your new oil filter housing, including engine oil, G48 or HT-12 coolant (depending on what your BMW came with from the factory), and automatic transmission fluid for models with the ZF 8HP transmission.
BMW's B58 engine has been very successful and has proved to be a reliable powerplant that is highly capable of producing some crazy power figures. Unfortunately, in true BMW fashion, the B58 engine does have a few problems that can become serious issues if not addressed quickly.
One of these issues is the oil filter housing cracking and leaking engine oil and/or coolant. BMW chose to construct the oil filter housing out of plastic and the housing tends to split if the cap is tightened too tight or even just over time as the plastic becomes brittle from numerous heat cycles. Another common failure point is the multiple gaskets that seal the housing to the engine block and between the housing and the engine oil cooler. when these seals fail, you will notice coolant and/or oil loss, or even the mixing of engine oil with coolant. There is also the possibility of your oil filter collapsing inside of the filter housing and preventing proper oil filtration and flow, sometimes clogging the small oil channels in your filter housing as the oil filter begins to fall apart. Though this is more common with vehicles that see extended oil change intervals, such as 12K+ mile oil changes, we have seen some failures as soon as 5,000 miles after an oil change!
Whatever the cause may be, the solution is almost always the same, replacement of the whole oil filter housing. We have put together a kit including the basic components needed to replace your oil filter housing and get your BMW back on the road!
Included:
Genuine BMW Engine Oil Filter Housing - Includes a new cap, seals, and oil filter (oil cooler not included and must be reused or purchased new - see BMW # 11428583901)
Oil Cooler Mounting Hardware
Oil Drain Plug Gasket
Intake Manifold Gaskets
Throttle Body Gasket
Transmission Fill Plug (For Automatic models)
Genuine BMW Installation Hardware
Not included in this kit are the fluids that will need to be replaced or topped off after the installation of your new oil filter housing, including engine oil, G48 or HT-12 coolant (depending on what your BMW came with from the factory), and automatic transmission fluid for models with the ZF 8HP transmission. We recommend the following:
This Product Is Covered By Our Lifetime Replacement Program
Products protected by our Lifetime Replacement Program are covered for as long as you own the product, no need to worry about an expiration date. Purchase your products and enjoy some worry-free motoring, knowing we've got you covered.
If you have any questions, would like to learn more or are ready to place a replacement claim, click here!
Fits These Cars
MAKE
MODEL
SUBMODEL
ENGINE
Special Fitment Notes
BMW
F22
M240i
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F22
M240i xDrive
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F23
M240i
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F23
M240i xDrive
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F30
340i
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F30
340i xDrive
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F32
440i
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F32
440i xDrive
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F33
440i
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F33
440i xDrive
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F34
340i xDrive
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F36
440i
B58 3.0L
Use vehicle selector to confirm fitment
BMW
F36
440i xDrive
B58 3.0L
Use vehicle selector to confirm fitment
BMW
G01
X3 M40i
B58 3.0L
For earlier vehicles with the Gen1 B58 (B58A) - not compatible with the B58TU (B58D) engine
BMW
G02
X4 M40i
B58 3.0L
For earlier vehicles with the Gen1 B58 (B58A) - not compatible with the B58TU (B58D) engine
BMW
G11
740i
B58 3.0L
For earlier vehicles with the Gen1 B58 (B58A) - not compatible with the B58TU (B58D) engine
BMW
G11
740i xDrive
B58 3.0L
For earlier vehicles with the Gen1 B58 (B58A) - not compatible with the B58TU (B58D) engine
BMW
G30
540i
B58 3.0L
For earlier vehicles with the Gen1 B58 (B58A) - not compatible with the B58TU (B58D) engine
BMW
G30
540i xDrive
B58 3.0L
For earlier vehicles with the Gen1 B58 (B58A) - not compatible with the B58TU (B58D) engine
*The above product applications have been written by Turner Motorsport. All
warranties, product application, fitment, and performance are the responsibility of Turner Motorsport.
For additional information see the terms of use.