BMW Drivetrain Parts for BMW E46 M3 S54 (1999-2005)

Sometimes choosing the correct shift kit proves difficult when you dual-purpose your favorite vehicle, we understand this well. The early days for any race enthusiast usually begins with a car that is needed to daily drive and setup to get out on the track. What becomes difficult is properly modifying that car to feel comfortable in both situations which is why we took this view on our new short shift line. This upgraded lever is a quick swap option to replace the standard shift lever that come with our kits so you can keep your hands closer to the wheel while shifting at high speeds. Designed from anodized aluminum this lever looks great in any interior for the daily driver who simply prefers the taller lever look and feel.

NOTE THAT THESE ARE DESIGNED TO WORK WITH TURNER MOTORSPORT SHORT SHIFTERS ONLY - We wanted to give you the option to buy one separately, in case you changed your mind after buying our short shifter.

Features:

Compatible with stock shift boot fits nicely into the machined groove at the bottom of the lever to maintain a clean look in the interior.
Machined from 6061-T6 aluminum and type II anodized for exceptional durability and corrosion resistance.
Available in either black or clear anodize to match your vehicle’s interior.
Rally shift knob is machined from black delrin.
Unlike aluminum, delrin will not hold heat so on those hot days you won’t have to worry about burning your hand on a knob that’s been baking in the sun.
Shift knob is threaded onto the end of the shift lever utilizing a standard ⅜-16 thread to allow for easy removal and attachment of your favorite beer tap or other accessory.
“Quick Change” height adjustable upper shift lever design allows for quick swapping between optional “OE” style and “Rally Style” upper shift levers.
22mm adjustment range to fine tune shifter throw and feel.

Adapt an N54 or N55 GS6-53BZ transmission to your M5x/S5x engine to unlock superior torque capacity and optimized gear ratios.

Engineered for the BMW enthusiast who demands more strength and better gear ratios, the Turner Motorsport Transmission Swap Flywheel Kit provides a direct solution for mating a modern N54 or N55 6-speed gearbox to your M20, M5X, or S5X engine. This kit bridges the gap between generations, allowing you to run a high-capacity GS6-53BZ transmission without the typical fabrication nightmares.

The technical core of this kit is our dual-geometry flywheel. By utilizing this specialized design, you can retain your engine-side stock starter while using the factory clutch and throw-out bearing from your donor transmission. This ensures a precise fit and a firm, factory-like shifting feel that can handle significantly more power than older 5-speed setups. To guarantee a fitment, we’ve included a precision drill guide for bellhousing alignment and a universal pilot bearing pin to simplify the installation process.

Features and benefits:

Compatible with the starter from your original motor.
Uses factory clutch and throwout bearing from the donor transmission (GS6-53BZ).
Comes with necessary tools and a provided drill guide to adapt the top transmission mounting holes.
Kit contents:

Swap Flywheel
Pilot bearing input adapter for late N54 and N55 GS6
Drill guide, bit, and hardware.
Flywheel bolts
Optional pilot bearing
Optional clutch
Swap notes:

Fits M20/M50/M52/S50/S52/S54 engines
Needs a custom driveshaft and rear transmission mount. (We used https://www.hdtautoparts.com/driveshafts)
For E46 only: Rear transmission mount can be used from E46 330 6 Speed. Part numbers (22316760531 & 22316760532)
Installation and Support:

Click HERE for installation instructions:

Single piece 6061 construction, optimized cooling, provisions for temp sensor and external cooler!

Built to last, made from a single piece of 6061 billet aluminum with a rugged and good-looking hard-coat anodizing our diff cover can handle anything you throw at it. Not only is it an absolute masterpiece to look at but this billet diff cover checks all the boxes for features needed. Reinforced mounting ears for strength and stability, never again will you break an ear off your diff cover like the factory units are known to do. Each ear is unified with the one-piece billet cover and features added material for the highest durability possible. This diff cover is cool, literally, the entire construction was designed with optimized cooling in mind. Internal fins are strategically placed serving as effective heat sinks for optimal heat dissipation. This ensures stable temperatures, promoting longevity for both the fluid and your differential. Additionally, the internal design ensures continuous oiling and lubrication of the ring gear, maintaining its stability and preventing fatigue by controlling heat more effectively. An internal baffle at the cover's corner helps maintain proper pressure and prevents cavitation.

All of the OEM features were retained along with the upgrades. The mounting surface was designed to be compatible with both the OEM gasket or RTV of your choosing, some people don't trust the gaskets and we get it. Factory bushing geometry allows you to use any E46 diff busing including rubber, poly, and even solid mounts. The drain and fill plugs on the diff cover are upgraded to -6AN using the provided high-pressure fittings with replaceable o-rings. The drain and fill plugs can now also be used for expanding to an external oil cooler allowing you to further expand the fluid capacity for optimized cooling and service intervals. To keep an eye on things from the driver seat is 1/8 NPT provision for temp sensors, this product from Turner has you covered at every turn.

Why the upgrade?

Upgrading to our Billet Differential cover gives you the strength you need to push your car to its limits. In addition to its enhanced strength, this differential cover includes numerous other upgrades and conveniences. These include increased capacity, improved cooling and lubrication for the ring gear, upgraded fill and drain plugs, and the option to expand an external oil cooler for extreme motorsport usage. Designed to complement both upgraded daily drivers and extensively modified track cars, all while looking good in the process.

Key Benefits:

Reinforced mounting ears for strength and stability - never again will you break an ear off during an aggressive drive or track event
Increased capacity
Sight glass for checking fluid level without removing fill/drain plug
External fins on the casing for maximum cooling and consistent fluid temps
Internal cooling fins for even more temperature control
Optimized internal design to keep fluid consistently on the ring gear
Integrated breather to prevent cavitation by venting the appropriate amount of pressure being built up in the diff housing
-6AN ports to incorporate the use of a differential cooler - this increases capacity and lowers temps allowing for extended fluid change intervals
1/8 NPT fitting for the use of a temp sensor to monitor fluid temperature
Design:

Fits large case 210/215mm differentials
Single piece 6061 Billet aluminum construction
T6 Black hard coat anodizing for superior corrosion resistance and aesthetics
Compatible with most differential coolers(-6AN) and temp sensors(1/8 NPT)
Designed to accommodate oversized rear sway bars
Retains OEM mounting features including the use of the OEM gasket
Factory geometry bushing size for use with OEM and aftermarket poly bushings
Easy access to sensors and drain/fill plug
Retains OEM speed sensor and wire mount location
Product development:

Our Reinforced Billet Diff Cover was designed, engineered, tested, and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

Elevate your BMW's shifting dynamics with this all-inclusive upgrade kit meticulously designed to counteract the wear and tear commonly found in stock rubber bushings and plastic inserts. Over time, these parts tend to degrade, resulting in a diminished shifter feel that compromises the driving experience.

This comprehensive upgrade package comprises top-tier components, notably the ECS Tuning Teflon Oval Shifter Bushings, Turner Motorsport Poly Shifter Arm Bushing, and Turner Motorsport DSSR. Collaboratively, these components target and eliminate the undesirable play and imprecision in the shifter mechanism, ensuring a more responsive, precise, and enjoyable shifting experience.

Key Benefits:

• Comprehensive kit replacing worn-out stock rubber bushings and plastic inserts.
• Enhances shifter precision and tactile feedback for a more engaging driving experience.
• Eliminates slop and play in the shifter mechanism, ensuring crisper, more precise shifts.
• Includes all necessary components and hardware for a complete and thorough shifter overhaul.

Used when retrofitting an OEM or aftermarket CSL intake on a vehicle with SMG transmission.

Its no secret the CSL intake plenum is the pivotal upgrade for your S54. If you are fortunate enough to have an SMG equipped vehicle you are going to need a bracket to relocate the expansion tank. Our Turner motorsport bracket fits perfectly with the engine bay to facilitate the installation of your genuine or Turner branded CSL intake plenum.

Design:

Direct fit, perfect OEM replacement
304SS sheet metal design, engineered to be simpler and cheaper than its formed OE counterpart
Reverse engineered with FARO laser scanning and Solidworks CAD technology

ECS Tuning's Polyurethane Transmission Mounts are designed to address the vital role of transmission mounts in your vehicle's suspension. The factory mounts are notorious for failures that can result in over-revving, mis-shifts, and in extreme cases, potential chassis damage. Our polyurethane mounts provide a robust solution, engineered for both street and track applications, guaranteeing enhanced performance while eliminating concerns about torn mounts.

Polyurethane stands out with its exceptional toughness, durability, and impressive wear resistance compared to rubber. It also exhibits resistance to water, oil, and grease while retaining its original shape even when subjected to significant compression. By reducing deflection, polyurethane facilitates effective power transfer. While there may be a slight increase in NVH (Noise, Vibration, Harshness), the benefits far outweigh this minor compromise in ride comfort. With a polyurethane durometer of 70A, our street mounts are versatile, offering both daily driving comfort and track durability. For more track-oriented enthusiasts, we provide stiffer mounts with an 80A durometer rating.

For a hassle-free installation, we supply a comprehensive DIY guide. ECS Tuning ensures that you are fully supported from start to finish.

This braided stainless steel line replaces the stock hydraulic hose connecting your clutch slave cylinder to the clutch master cylinder. There are several deficiences with rubber, especially as it ages - when new the rubber expands and swells under pressure and the pedal can feel spongy. As rubber ages and is exposed to extreme temperatures the rubber can harden and even shrink (common on brake hoses), which results in a stiff pedal. Rubber clutch lines do not stand up to the stresses of hard use. ECS Exact-Fit stainless reinforced clutch lines provide more confident and dependable shifting by maintaining consistent line pressure, long lasting corrosion resistance, and increased protection from failure. These lines are reinforced with braided stainless steel mesh, affording superior expansion resistance. This resistance to expansion creates a firmer pedal, and a more direct clutch pedal feel. The signature red polymer coating provides additional protection from the elements and abrasion.

This particular stainless steel clutch line fits the following BMWs:
1999-2005 E46 3 Series (all) including 323i, 323Ci, 325i, 325xi, 325Ci, 328i, 328Ci, 330i, 330xi, 330Ci
2001-2006 E46 M3 (manual transmission only, no SMG)
2004-2009 X3 SAV including X3 2.5, X3 3.0

Upgrade the shifting precision and feel of your BMW with Turner Motorsport Powerflex Shifter Carrier Street Bushings - Oval. Made of 90A urethane, these bushings replace the stock rubber ones to prevent sloppy shifting. The stiff urethane reduces play without adding vibration. Easy to install when the carrier is out of the car, these bushings ensure improved performance. Here are the key benefits:

• Enhances shifting precision and feel
• Prevents sloppy shifting caused by failed rubber bushings
• Made of 90A urethane for durability and stiffness
• Easy installation when carrier is removed

The ECS Tuning Center Support Bearing Brace is engineered to improve drivetrain performance and longevity. The factory center support bearing features internal an internal rubber bushing to reduce NVH (noise, vibration, and harshness) transmission to the cabin. Unfortunately, this material choice falls short when it comes to performance applications. Under extreme load conditions, this bushing is prone to flexing, resulting in driveshaft misalignment. To address the shortcomings of the factory rubber center support carrier design, ECS engineers developed a set of precision-fit, split polyurethane bushings that secure tightly around the existing driveshaft bearing. Constructed from 30A durometer polyurethane, this material eliminates bushing deflection while maintaining minimal noise, vibration, and harshness (NVH). By eliminating deflection, this innovative solution not only improves durability but also ensures a significantly longer service life than the OEM center support bearing—making it an excellent upgrade for aging BMW chassis.

The polyurethane bushings are surrounded by a robust 6061-T6 billet aluminum bracket designed with strength and reliability in-mind. This bracket features a split design for hassle-free installation, eliminating the need to remove the driveshaft assembly entirely. To install the ECS Center Support Carrier, simply cut around your existing bearing, remove the factory brace, and clamp on your new bushings and bracket. This user-friendly approach saves time and simplifies maintenance or upgrades. Two stainless steel socket head screws are used to fasten the two-piece bracket, offering corrosion resistance and secure clamping under high torque and stress. This combination of materials and design ensures dependable performance and long-lasting durability, even in demanding applications.

Features & Benefits:

Performance-Designed Bushing Upgrade: 30A durometer polyurethane is used to eliminate bushing deflection while maintaining a smooth, quiet ride. Improved Longevity: Polyurethane construction offers a longer lifespan than factory rubber, ideal for enthusiasts looking to eliminate future CSB-related problems. Billet Aluminum Bracket: The upgraded bushings are encased in a 6061-T6 billet aluminum bracket for enhanced durability and improved performance. Easy Installation: Both the bushings and the bracket feature a two-piece split design, allowing for seamless installation without driveshaft removal. Reduce Deflection, Increase Rigidity: Designed with performance in mind, this upgrade eliminates excessive driveshaft movement for improved alignment and efficiency. Kit Includes:

ECS Driveshaft Center Support Bushings ECS Driveshaft Center Support Carrier (2) Stainless Steel Hex Head Screws (2) Flange Nuts (26117574872) Medium Strength Threadlocker (0.5ml) Installation Instructions:

ECS has provided a detailed, start-to-finish installation guide to aid in the process of installing your new Driveshaft Center Support Carrier.

Stock mounts are made from soft rubber and are sometimes filled with fluid to give a car the most comfortable ride possible. The soft rubber and fluid helps to reduce the total amount of vibration, noise, and harshness (NVH) that is transferred into the cabin. The problem with this is driveline slop. The stock mounts allow a lot of excess movement and increases the amount of time it takes to transfer power to the wheels.

In order to address this issue, performance mounts can be substituted to reduce the amount of slop and transfer power to the wheel quicker. Two options for this are polyurethane mounts and solid mounts.

Solid mounts are great for an immediate transfer of power but allow for a ton of noise and vibration to be felt and heard in the cabin of the vehicle. This is great for the track where there aren't any issues with excess harshness, but as a daily driver, this can become an annoying pain in the neck.

The best middle ground is Polyurethane. Polyurethane is much stiffer than rubber and gives you the much stiffer feel you may be looking for. This allows for the increase in responsiveness, but isn't so extreme that it transfers all of the sound and vibrations into the cabin. This makes it much more comfortable for daily use while still reinforcing your driveline.

Features:

• Aluminum and Polyurethane Construction
• 80A Durometer Rating
• New Hardware

Revitalize your driving experience with ECS Tuning's In-House Engineered Performance Polyurethane Differential Bushings. Say goodbye to soft factory rubber bushings and their deflection. These innovative bushings provide a substantial improvement in the connection between your right foot, the chassis, and the wheels. The outcome is a crisper power transfer from the differential to the wheels, resulting in enhanced throttle control for various driving activities. Notably, these polyurethane bushings achieve these benefits without the harshness or vibration often linked to delrin or solid differential mounts.

Manufactured using a robust 88A durometer polyurethane and a black anodized 6061-T6 aluminum sleeve, these bushings offer superior resistance to chemicals, ozone degradation, road salt, and general wear and tear. This translates to an extended service life.

Some modifications to your vehicle may not produce power to create gains in the overall performance of your driving. When you add a "Po' Boy" clutch stop to your BMW the performance gain is directly felt in the driving experience.

The ECS clutch stop allows the driver to fine tune the position of the clutch pedal to closely match the engagement point for precise, quicker shifting. The adjustment range found in this product can be set to the stock engagement point or can be adjusted to follow the wear of the clutch.  Meaning your new experience will never change all the way to the end of the clutch life and can be reset to enjoy the next clutch.

Note: This modification might require some slight modification to the clutch switch mounting bracket, which can be bent slightly by hand.

Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.

By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components. 

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Enhance your driving experience with ECS Tuning's Performance Polyurethane Differential Bushings. These meticulously engineered bushings offer a direct connection between your right foot, the engine, and the chassis, making them an essential upgrade.

• Say goodbye to the softness of factory rubber differential bushings that absorb vibrations and reduce performance.
• ECS Tuning's polyurethane bushings eliminate the deflection found in factory rubber bushings, resulting in improved power transfer from the differential to the wheels.
• Experience enhanced throttle control, whether you're navigating a challenging canyon road, drag racing, or simply commuting.

Unlike delrin or solid differential mounts, these bushings deliver improved performance without introducing harshness or excessive vibration.

Crafted from durable 88A durometer polyurethane and enhanced with a black anodized 6061-T6 aluminum sleeve.

Resistant to chemicals, ozone degradation, road salt, and general wear and tear, ensuring a longer service life.