Turner Motorsport for BMW 3 Series E46 (1999-2005)

These camber plates are perfect for the enthusiast owner who wants a high quality design with a motorsports background. Knowing a full race kit on the street is not often the best option, we took the best features from the Race Camber Plates and incorporated them into a fresh Street design -

• preserves the correct E46 M3 geometry
• separate sliding camber and caster adjustments
• maximum shock travel
• light weight
• durable materials
• large surface area
• ease of use

The Turner E46 M3 Street Camber Plates are the most advanced design on the market. These are designed specifically for the E46 M3 - no shortcuts or cookie-cutter components. We started with a fresh design to make these very user friendly and easy to install and set up. The E46 M3 front suspension has unique geometry and the strut is mounted at an angle that can put significant side loading on the strut shaft if it's not located properly. The location and angles for the main bearing were carefully engineered to allow the proper motion ratio and strut angles during adjustment. This greatly reduces bending forces on the strut itself which improves performance and longevity. By designing for one chassis we're able to focus on what works best in that application - proper fitment and operation without unnecessary adapters, easy-to-use camber and caster adjustments, and an intelligent modular design.

For street use we added a pliable urethane bushing to absorb vibration and a special base design that works with the factory radial bearing and spring perch. The radial bearing allows the spring to rotate instead of twisting and binding. By re-using the factory radial bearing we can keep the assembled stack height lower for maximized shock travel. It's also a commonly-available item that you can get from any BMW dealer at a low price. All of the things that make it work well in the factory application carry over to our design. You can use our camber plates with a stock sized spring, 60mm, or 2.5" springs. Use your stock spring perch/bearing with stock-sized springs. The 60mm and 2.5" upper spring perches are sold separately. The beauty of our design is that you can use the factory radial bearing with any of these springs.

Another important feature of the Turner Camber Plates is the size of the upper plate. Our plates have a very large surface area to better spread strut forces through the strut tower. A smaller upper plate, like those found on competitor's kits, will localize strut forces and contribute to strut tower deformation ('strut tower mushrooming'). This is a very important feature especially as these cars get older and spend more time on the track. Deformed strut towers are a serious performance and safety concern and our camber plates are properly designed to handle the loads. The factory strut reinforcement plates are not required with our camber plates (but you can use them if you want to).

Since this design is specific to the E46 M3, we can build it with the bare minimum of adapters and extra hardware. This not only cuts down on confusion but makes it easier to assemble and operate. We use the correct-sized bearing for the 16mm strut shaft; no sleeves or bearing adapters required. The original tapered lower mount support and a small stainless steel spacer from our kit are all that's required to install. We have used our camber plates with most of the major strut manufacturers on the market - stock Sachs/Boge, Bilstein, Koni, H&R, ST, and KW. Our camber plates work with any strut that is designed to accept the factory strut mount.

Click here for installation instructions.

This item fits the following BMWs:
2001-2006 E46 BMW M3

These aluminum pedals were designed with one thing in mind -- performance. We wanted a pedal set that gave us the grip EXACTLY where we wanted it: MASSIVE GRIP on the brake and clutch pedals, and far less grip on the accelerator to allow the right foot to better slide/move during heal-toe braking. This set surpasses all others in this area, giving your BMW's foot operated controls a more tactile feel and response. The brake and clutch pedals feature pyramid shaped spikes, which actually BITE the soles of your shoes PERFECTLY, creating the ultimate (and unbeatable) friction surface. 

These pedals are 100% MADE IN THE USA, and are CNC machined from aircraft quality aluminum billet to perfectly fit your BMW. There's no rubber to wear out, and no cosmetic finishes to chip or flake off. Stainless steel hardware is included, as well as a basic installation guide (professional installation always recommended). These pedals are for left-hand drive (LHD), manual transmission BMWs only (including SMG and DCT sequential manual gearboxes -- on these cars, you will only use one of the included clutch/brake sized pedals). Please note on E36 convertible models (1994-1999) the optional footrest requires modification. 
 

These aluminum racing pedals fit the following left-hand drive BMWs:
2014+ F22 BMW 228i M235i 
1984-1991 E30 3 Series - 318i, 318is, 325, 325e, 325es, 325i, 325is, 325ix ** with MANUAL transmission
1992-1998 E36 3 Series - 318i, 318is, 318ti, 325i, 325is, 328i, 328is, 323is ** with MANUAL transmission
1996-1999 E36 M3 including 3.2 liter M3 ** with MANUAL transmission
1999-2005 E46 3 Series - 323i, 323Ci, 328i, 328Ci, 325i, 325Ci, 325xi, 330i, 330Ci, 330xi ** with MANUAL trans
2001-2006 E46 M3 coupe & convertible (SMG uses only one brake/clutch pedal)
2008-2013 E82/E88 1 Series - 135i coupe & 135i convertible with MANUAL or DCT
2006-2011 E90/E92 3 Series - 325i, 325xi, 328i, 328xi, 330i, 330xi, 335i, 335xi ** with MANUAL transmission
2008-2013 E90/E92/E93 M3 including M3 sedan, M3 coupe & E93 M3 convertible (DCT uses only one brake/clutch pedal)
2012+ F30 BMW 320i 320i xDrive 328d 328d xDrive 328i 328i xDrive 335i 335i xDrive - Sedan
2013+ F31 BMW 328i xDrive 328d xDrive - Wagon
2014+ F34 BMW 328i xDrive GT, 335i xDrive GT - Gran Tourismo
2015+ F80 BMW M3 (DCT uses only one brake/clutch pedal)
2013+ F32 BMW 428i 428i xDrive 435i 435i xDrive - Coupe
2013+ F33 BMW 428i Convertible 428i xDrive Convertible 435i Convertible - Convertible
2014+ F36 BMW 428i Gran Coupe 428i xDrive Gran Coupe 435i Gran Coupe 435i xDrive Gran Coupe
2015+ F82 BMW M4 (DCT uses only one brake/clutch pedal)
1989-1995 E34 5 Series - 525i, 530i, 535i, 540i ** with MANUL transmission
1997-2003 E39 BMW 525i 528i 530i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5 (SMG uses only one brake/clutch pedal)
2011+ F10 BMW 528i 528i xDrive 535i 535i xDrive 535d 535d xDrive 550i 550i xDrive M5 (DCT uses only one brake/clutch pedal)
2004-2010 E63 BMW 645ci 650i M6 (SMG uses only one brake/clutch pedal)
2012+ F12 BMW 640i 650i 650i xDrive M6 (DCT uses only one brake/clutch pedal)
2013+ F06 BMW 640i Gran Coupe 650i Gran Coupe 650i xDrive Gran Coupe M6 Gran Coupe (DCT uses only one brake/clutch pedal)
1996-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

3.0" Inner Diameter
4.0" Outer Diameter
Black Chrome Finish
Double Wall Construction
Straight Cut Style
Includes Stainless Steel Clamp

Rear Axle Carrier Panel (RACP) failure is a well-documented issue that plagues all BMW E46 models. Due to thin sheet metal mounting, the forces applied during cornering, acceleration, and braking create stress fractures in the carrier panel, resulting in large cracks or breaks that risk the structural integrity of your chassis. To fix this issue, many enthusiasts opt to install weld-in reinforcement plates on the underside of the RACP. While this remedies the formation of additional stress cracks and adds rigidity to failure-prone areas, it does not prevent the entire carrier panel from flexing during high-performance driving.

Our all-new Rear Subframe Reinforcement Brace is engineered to add structure to the E46's rear chassis under high-stress conditions, eliminating the common weak points in the RACP while providing the confidence you need for performance driving. Don't let chassis flex limit your car’s potential—upgrade your E46 with the Turner Motorsport Rear Subframe Reinforcement Brace today!

How It Works:

During performance driving, the Rear Axle Carrier Panel (RACP) must react the forces of longitudinal and lateral accelerations. During forward acceleration, the differential transmits torque through the subframe to the RACP, forcing the rearmost subframe mounting points downward. This downward movement flexes the carrier panel, reducing its ability to handle torque efficiently. By linking the rearmost subframe mounting points to the rear shock towers, downward flex is restricted, resulting in improved torque transfer and stability. Alternatively, high-grip cornering generates lateral acceleration (side-to-side) forces across the RACP. Similar to how a rear strut brace functions, connecting the rear shock towers helps to counteract these forces. Adding the subframe to this connection further reduces lateral loads, eliminating side-to-side flex and enhancing overall stability.

Features & Design:

Four-Point Triangulated Structure: Links the rearmost subframe mounting locations to both rear strut towers for superior load distribution. Enhanced Stability: Reduces lateral and longitudinal RACP flex during acceleration, braking, and cornering. Improved Torque Transfer: Minimizes downward flex of the RACP, ensuring efficient power delivery for enhanced driveability. High-Performance Durability: Heavy-duty steel tube construction ensures lasting support during spirited driving, track use, and for vehicles with increased power output. Blue Powdercoat Finish: Offers fantastic corrosion resistance, protection from scuffs and scratches, and a stylish appearance that is sure to complement your performance-centric E46. Underside Reinforcement Compatibility: Designed to work seamlessly alongside our underside RACP reinforcement plates (TDR4675412, T#91). Kit Includes:

Rear Subframe Brace Sedan Subframe Brace Spacers Extended-Length Drill Bit (1/4", 12" Overall Length) High-Speed Drill Bit (12.5mm, 152mm Overall Length) Drill Bit Guide Extended Subframe Bolts Zinc-Plated Steel Hex Nut (2) Installation & Support:

Need installation tips? Our team has assembled a guided start-to-finish installation tutorial, including detailed instructions on drilling and cutting your trunk floor panel for perfect fitment. Click HERE for Installation Instructions

Unlock the full potential of your S54’s valvetrain with our High Performance Cam Followers/Rocker Arms, built for precision, durability, and reliability in high-revving performance engines.

Crafted from forged chromoly steel and finished with a diamond-like carbon coating, these cam followers are engineered to deliver exceptional strength, reduced friction, and outstanding wear resistance, ideal for demanding street or track use. Each unit is precision-ground for consistent clearances and smooth, stable valvetrain motion at all RPMs. Despite heavy-duty construction, our design retains the same weight as the factory rocker arm, preserving OE valvetrain geometry and balance while offering superior longevity and performance.

Rocker arms wear in conjunction with the camshafts, meaning the two must be replaced simultaneously. Aftermarket and performance camshaft options (Schrick, CAT-Cams, etc.) are typically ground from softer blanks and, as a result, cannot be used with factory rocker arms. We tested our performance cam followers with aftermarket camshafts to validate compatibility, ensuring smooth, reliable, and safe operation under demanding conditions.

Features:

Forged chromoly construction for maximum strength and durability Diamond-like carbon-coated surface reduces friction, extends service life, and permits compatibility with aftermarket and performance camshaft options Precision-ground tolerances ensure consistent and quiet operation OEM weight match maintains valvetrain balance and reliability Superior wear resistance for performance and endurance applications NOTE: Rocker arms are wear items and must be replaced alongside a new set of camshafts, regardless of profile or manufacturer. Installing a new set of rocker arms onto a used set of camshafts is NOT recommended.

Kit Contents:

One set of 12 DLC-Coated Rocker Arms (services intake OR exhaust camshaft) 24 Rocker Arms / 2 Sets of 12 Rocker Arms required to complete both intake and exhaust camshafts. Product Development: Our Turner Performance Rocker Arms are the result of advanced engineering, testing, and quality assurance by Turner’s Research & Development team. Every stage of development employs FARO laser scanning, SolidWorks 3D CAD modeling, and in-house rapid prototyping for precise fitment and design validation. Performance and durability are proven through Mustang AWD 500 SE dyno testing and Superflow SF-750 Flowbench analysis, ensuring each component meets Turner’s uncompromising standards for performance and quality.

Sometimes choosing the correct shift kit proves difficult when you dual-purpose your favorite vehicle, we understand this well. The early days for any race enthusiast usually begins with a car that is needed to daily drive and setup to get out on the track. What becomes difficult is properly modifying that car to feel comfortable in both situations which is why we took this view on our new short shift line. This upgraded lever is a quick swap option to replace the standard shift lever that come with our kits so you can keep your hands closer to the wheel while shifting at high speeds. Designed from anodized aluminum this lever looks great in any interior for the daily driver who simply prefers the taller lever look and feel.

NOTE THAT THESE ARE DESIGNED TO WORK WITH TURNER MOTORSPORT SHORT SHIFTERS ONLY - We wanted to give you the option to buy one separately, in case you changed your mind after buying our short shifter.

Features:

Compatible with stock shift boot fits nicely into the machined groove at the bottom of the lever to maintain a clean look in the interior.
Machined from 6061-T6 aluminum and type II anodized for exceptional durability and corrosion resistance.
Available in either black or clear anodize to match your vehicle’s interior.
Rally shift knob is machined from black delrin.
Unlike aluminum, delrin will not hold heat so on those hot days you won’t have to worry about burning your hand on a knob that’s been baking in the sun.
Shift knob is threaded onto the end of the shift lever utilizing a standard ⅜-16 thread to allow for easy removal and attachment of your favorite beer tap or other accessory.
“Quick Change” height adjustable upper shift lever design allows for quick swapping between optional “OE” style and “Rally Style” upper shift levers.
22mm adjustment range to fine tune shifter throw and feel.

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

These E46 fixed camber plates are designed from knowledge gained from our highly successful racing campaigns with the E46 in the Speed World Challenge series. These plates are offset for the best camber and caster combination for racing purposes when using the stock-diameter sized springs. Camber increases to between -2.5° to -3.0°, depending on each individual car. While ride height is increased by 1/4", the benefit of these plates far outweighs the minor ride height increase. The rate of camber change is virtually unaffected throughout the range of suspension travel, reducing the need for other geometry correction. Material has also been added to increase surface contact area therefore reducing the strut tower deformation and increasing the strength of the strut towers. Fixed mount camber plates are legal in many racing and autocross classes. These are the perfect camber solution when adjustable plates are not allowed in your class. These are a simple bolt on part for all E46 except the xi and M3 models.

Instructions for Turner E46 Front Fixed Camber Plates

This item fits the following BMWs:
1999-2005 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci

The E46 M3 CSL sparked a lot of interest among enthusiasts about the "high kick" look. But what about those who want the aggressive, high kick look without having to replace the entire trunk? We found ourselves scratching our heads, especially unsatisfied with the add-on CSL spoilers you can find on the market.

We took it upon ourselves to CAD design an aggressive, high kick spoiler that pays homage to the CSL trunk, while flowing perfectly with the simple, yet aggressive body lines of the E46 coupe. The carbon fiber is hand laid, with a beautiful gloss finish that will match well with any other carbon fiber accents on your E46 coupe. Our high kick rear spoiler will instantly give your vehicle a more aggressive look.

Turner has developed a new superior zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Ditch your failure-prone plastic end tanks and increase cooling capacity by 25%—all without modifying your core support or accompanying shrouds. This Performance Triple-Pass Radiator is the ULTIMATE cooling system upgrade for your S54-equipped BMW!

The E46 M3 is a masterclass in German engineering. Harboring six independent throttle bodies, infinitely variable dual-VANOS, and an 8,000 RPM redline, the S54 is practically a racing engine for the road. Unfortunately, the engine's motorsport pedigree didn't quite make it to the cooling system. The OEM radiator, while superior to its non-M counterpart, struggles to keep coolant temperature in check under sustained high-RPM conditions. Heat soak, elevated operating temperatures, and component fatigue are all too familiar to M3 owners who track their S54 regularly.

To solve this problem, we teamed up with CSF Race, a global leader in high-performance cooling solutions with over five decades of industry experience. Together, we developed the CSFxTurner Triple-Pass Radiator: a high-performance, no-compromise solution built to meet the cooling demands of track-day warriors.

Part Design:

CSF-Exclusive "B-Tube" Technology Unlike conventional "O-tube" designs, CSF’s patented B-tube structure increases wall strength while creating a more efficient flow path. This alone accounts for a 15% increase in cooling capacity over an OE "o-tube" radiator! Triple-Pass Core Design As the name suggests, this unique structure forces coolant through the core three times before exit, resulting in a substantial temperature delta across the radiator core. Two-Row Compact Structure This radiator was designed with precise fitment in mind. While total tube count and size are increased, the overall radiator dimensions stay the same as OE, ensuring a drop-in fit with zero modifications required. 25% Increase in Cooling Capacity All of the above design features translate to a massive 25% cooling increase over the stock radiator! Features & Performance Benefits:

Direct-fit upgrade—no modifications required! Accepts all OEM attachments via CNC-machined "Quick-Connect" hose ends and accessory mounting provisions TIG-welded aluminum construction provides increased durability An all-aluminum drain plug replaces the weak OE plastic unit, ensuring seamless functionality for the life of the radiator Increased cooling efficiency for high-performance and racing use Designed and tested by Turner Motorsport in collaboration with CSF Race

Flexible silicone smooths the intake tract while allowing for a range of performance intakes fitments. The ultimate in durability!

In most vehicle applications, the rubber intake elbow found in the intake system is not designed for performance or modification. They were designed to get the job done but when you add a performance filter, intake or tune, the stock elbow will start to show it weakness. The stock rubber elbows disrupt air flow as it passes over the accordion sections causing unwanted turbulence and negating the effects of intake modifications.

With high quality 4 ply construction, the Turner intake boot is strong but flexible, ensuring a secure fit on an OEM or aftermarket intake system. A smooth interior ensures unimpeded airflow, while a smooth, unassuming exterior adds to any engine bay.

Benefits:

Improved throttle response,
Increase induction sound
Increased power output - and power output, Best when paired with an ECS drop-in air filter.(ES4461001 or ES4460965)

A beautiful high kick carbon spoiler that pays homage to CSL design while flowing perfectly with E46 Sedan body lines!

Finally, sedan parts! The E46 chassis is amazing as a whole, with the abundance of sub-models made there are plenty of straight sixes to go around. Unfortunately for the sedan owners, there was never an E46 M3 made with four doors. This brings up a problem because the main focus of aftermarket parts were made for the M3 and the non-m coupe. Our engineers wanted to make sure the 4 door E46 owners were not forgotten.

Our Turner Motorsport's carbon high kick rear spoiler is a great way to add some aggressive style to the rear end of your E46 sedan. The fit and finish on this piece is truly beautiful, featuring hand laid gloss carbon fiber and a design that perfectly matches the body lines of the E46 sedan. This carbon trunk spoiler will give your E46 just the look you want.

Installation is very easy, with no drilling involved. Simply clean the surface area of the trunk, remove backing from the already attached high strength double sided tape, line it up and press firmly down. We recommend doing this in a warm environment as it will better adhere to the trunk.

Features & Specifications:

Designed and engineered in-house using state of the art 3D laser scanning and CAD technology for precision fitment.
Accentuates the OE body lines throughout the outer edge of the spoiler
Utilizes 3M double-sided tape for a strong bond to the body
Made from lightweight, 2x2 twill weave carbon fiber
Gloss clear coat for UV protection

Our unique and carefully designed front lip for the E46 M3 focuses on enhancing the car's aesthetics while preserving its natural beauty. This front lip is constructed of high-gloss, 3mm thick, 2x2 carbon fiber that adds a tasteful accent to the bumper while being strong and lightweight!

This aesthetic piece was crafted to stand out from other options available on the market by incorporating design elements that draw inspiration from the stock bumper but reimagines them in a way that sets it apart. Rather than overcomplicating the car's body styling, the goal was to seamlessly integrate the front lip with the existing design. This approach aims to enhance the car's body styling rather than overshadow it.

This versatile design is suited for both track use and everyday driving on the streets. Our E46 M3 front lip was designed to strike a balance between uniqueness and performance oriented aesthetics, while complementing the car's existing design. This is a clear cut choice front lip for someone looking to enhance the look of their M3.

Once you see your M3 with this front lip from, you will no longer think the front end is complete without it. Rounding out the near perfect car, this front lip completes the front end by filling out the open space underneath and sets the stage to enjoy the timeless body styling incorporating a curvature that compliments the front bumper.

Features & Benefits:

High-Gloss
Beautiful flowing carbon weave
Strong and lightweight
Updates the bumper with carbon appearance that enhances the existing body lines
Motorsport styling
Enhanced lowered appearance
Design:

CAD designed in-house for precision fitment
3mm 2x2 carbon fiber shell securely mounted at strong mounting points along the whole surface where the lip mates to the bumper
Front leading edge helps compliment and accentuate the forgotten body lines to add an aggressive yet subtle flare to the front end
Attaches to the front bumper with self tapping screws, plastic riv-nut and 6mm 3m adhesive tape to securely mount
Installation hardware included

Our experience with spherical front control arm ball joints go back to those we designed and used in our IMSA E90 328i and E92 M3 racecars (GS class Champions in 2011).  We wanted to offer e30, e36, and e46 owners similar levels of handling precision and control for the track and street, but weren’t satisfied with the other options out there.  Instead of a Delrin bushing or unsealed spherical bearing alone, we selected an oversized sealed greaseable spherical monoball to offer unparalleled durability and precision, but designed a Delrin adapter sleeve to help isolate the added noise, vibration, and harshness that a full solid monoball bearing will have. While race-ready, our hybrid Delrin/monoball control arm bearings are more at home on the street than other kits that are advertised as “race-only” bearings. We did extensive street, autocross, and track testing to ensure the spherical bearing used in this bushing design excelled in each setting.

The stock rubber bushings, even those found in the M3, allow significant fore/aft movement of the front wheels to help absorb road impacts, especially when being pushed hard.  This soft flexible design maximizes daily driving comfort, but also allows considerable alignment change.  This unwanted deflection stands between you and a crisp, confidence-inspiring driving experience.  The advantage of a monoball bearing is that it will not deflect under load, eliminating all unwanted deflection while still allowing complete freedom of movement in the desired angles. What you get is superior steering precision with better handling from more consistent alignment and direct braking feedback, with exceptional service life.  Thanks to the Delrin insert and double lip seals, there's none of the extra noise or reduced service life often found on other spherical bearings.

In short, if you're seeking front control arm bushings that offer precise, predictable handling, crisper braking feel, with a long service life free from noise - look no further. We have you covered.

Watch to learn more about Turner Monoball Bushings

Features:

Bearing housing

• Precision CNC machined from 6061-T6 blue anodized aluminum with a pre-installed grease fitting and grease distribution channels making this a serviceable design
• Knurled for smooth press fit in a wide variance in “lollipop” dimensions

Bearing

• A high quality greaseable double lip sealed bearing with Delrin® inserts. Delrin® was chosen for its durability under pressure, while still soft enough to create a perfect play-free fitment on the control arm.
• Replaceable for infinite service life - no need to replace the entire mount in the event a bearing happens to fail.

Includes new hardware. Grease before installation and with each oil service with high quality Moly grease for maximum service life. Need a grease fitting tool?

Installation is relatively easy - see our instructions here. 

This item fits the following BMWs: 
2001-2006 E46 BMW M3 

If allowed in the rules these solid aluminum transmission mounts offer many advantages over a urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. These are machined from solid aluminum and have zero deflection, engine torque will cause a rubber or urethane mount to flex or deflect allowing more torque to passed through the drive line (instead of being wasted winding up the mount). This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of transmission mounts you will ever need. We very strongly recommend using the solid transmission and engine mounts together as a complete kit, mixing a rubber mount with a metal mount will cause undue stress on the mounting points and will lead to a failure. We never advise using a solid mount unless a corresponding solid mount is also used.

These are a no-compromise design for all-out racing use, full solid aluminum mounts should not be used on street-driven cars since there is no material to absorb vibration making these quite harsh for regular street use (track cars don't care about noise).

Product features and benefits:

• Crisper throttle response, positive shifter location, direct power transfer
• Precision machined billet 6061-T6 aluminum housing
• Grade 10.9 stud - fear not, big turbo owners
• Engineered in-house and made in America

This item fits the following BMWs: 
1989-1995  E34 BMW  525i 530i 535i 540i M5 
1992-1998  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 
1997-2003  E39 BMW  525i 528i 530i 540i M5 
1999-2005  E46 BMW  323i 323ci 325i 325ci 328i 328ci 330i 330ci M3 
2008-2012  E82 BMW  128i 135i 1M Coupe 
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan 
2006-2012  E91 BMW  328i - Wagon 
2007-2013  E92 BMW  328i 335i 335is - Coupe 
2007-2013  E93 BMW  328i 335i - Convertible 
1997-2002  Z3 BMW  Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe ​