Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.

By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components. 

Engineered to perform, Powerflex performance polyurethane differential bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

BMW’s are known to have failure prone front thrust arm bushings.  The flexible rubber bushings, even those found in M performance models, allow significant movement of the front wheels to maximize daily driving comfort, but also allow considerable alignment change.  This results in a disconnected and numb road feel, standing between you and a confidence inspiring driving experience.  Eventually the fluid filled rubber bushings fatigue and crack due to continual deflection and ozone degradation, and eventually the damping fluid leaks out resulting in complete failure. 

For the enthusiast looking for superior performance and longevity with a crisp, confidence-inspiring driving experience, our sealed ball joint monoballs are the best solution available!  Our experience with spherical front control arm ball joints go back to those we designed and used in our IMSA E90 328i and E92 M3 racecars (GS class Champions in 2011).  We wanted to offer E31, E32, E34, E38, E39, E53, E60, E63, E64, and E83 owners similar levels of handling precision and control for the track and street. 

The bearing housing is precision CNC machined from 6061-T6 anodized aluminum and features a knurled OD to ensure a perfect press fit, and utilize a sealed OEM BMW ball joint for exceptional quality and durability, making them completely at home on both the street and track with no compromise.  We have done extensive street, autocross, and track testing to ensure the ball joint used in this bushing design excels in each setting.  The advantage of a sealed ball joint is that it eliminates all unwanted deflection while still allowing complete bind-free movement throughout suspension travel, resulting in exceptional control of wheel alignment.  What you get is superior steering precision, turn-in response, direct braking feedback, and better handling.

In short, if you're seeking the ultimate in precise, predictable handling and control, with crisp braking response and a long service life that’s equally at home on the street or track - look no further. We have you covered.

We offer these thrust arms with the monoball bushings pre-installed for your convenience. Since BMW recommends the control arms be replaced for every other bushing change, we prefer to sell these as a pre-assembled set. The bushings are also available separately if you wish to source your own control arms.

Features:

Bearing housing

• Precision CNC machined from 6061-T6 blue anodized aluminum
• Knurled OD to provide the perfect fit for the wide range of thrust arm bore diameters among brands.
• CNC machined 304ss ball joint sleeve inserts, providing a precision fit between the ball joint and the subframe. 

Bearing

• OEM BMW sealed and greased ball joint for exceptional durability and service life.

Performance

• Nearly instantaneous, crisp steering and braking response.
• Maintenance free, long lasting performance. 
• Improved road feel without undesirable NVH.

Sold as a pair for RWD models only.

Click here for installation instructions.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

Our E90 E92 E93 fixed camber plates are designed from the knowledge we gained from our highly successful racing campaigns with the E46 in the Speed World Challenge series. Our camber plates are offset for the best camber and caster combination for racing purposes when using the stock-diameter sized springs. Camber increases to -2.5° depending on your individual suspension setup, while only increasing ride height by 6mm. The rate of camber change is virtually unaffected throughout the range of suspension travel, reducing the need for other geometry correction. Fixed mount camber plates are legal in many racing and autocross classes - these are the perfect camber solution when adjustable plates are not allowed in your class.

These are very simple to install, requiring only pressing out locator dowels and studs in your factory strut mounts. See below for detailed instructions.

Control arms begin to wear over time, leading to sloppy control of your vehicle. Anything from knocking, steering vibration, or even loss of vehicle control could occur. An OEM replacement from�Lemf�rder is the perfect option to restore control and suspension quality.

OEM Lemf�rder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemf�rder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. �All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Our renowned TMS adjustable front sway bar / swaybar links for BMWs are now available in custom lengths, making them easy to order for any aftermarket or custom suspension setups. Simply measure for your ideal link length, and order the links with the best length range (below). Each sway bar link has a 10mm diameter mounting pin/stud, which is the typical factory/stock size for a universal fitment. These are sold by the pair, and each set includes two matching sway bar end links.

These end links offer the quiet operation and long life of "stock" BMW end links, but with the strength and adjustability of rod-end style sway bar links. These sway bar links can be used on a wide variety of BMWs and aftermarket BMW suspensions. When measuring, please consider that the length ranges of our Custom Adjustable end links are measured from the center to center on the end link mounting stud / pin, as shown in our diagram.

Note for E9X M3: the unique mounting on the M3 strut requires a set of our adapter seats (#TSU9912AF9). You can add them with your links from the menu below.
 

TMS Part#Center to Center (mm)Center to Center (inch)

TSU9912A35155.00mm - 170.00mm6.10" - 6.69"

TSU9912A40170.00mm - 185.00mm6.69" - 7.28"

TSU9912A45180.00mm - 195.00mm7.08" - 7.67"

TSU9912A50190.00mm - 205.00mm7.48" - 8.07"

TSU9912A55207.00mm - 222.00mm8.15" - 8.74"

TSU9912AF1220.00mm - 235.00mm8.66" - 9.25"

TSU9912A70240.00mm - 255.00mm9.45" - 10.04"

TSU4612AF3250.00mm - 265.00mm9.84" - 10.43"

TSU9912A80261.00mm - 276.00mm10.28" - 10.87"

TSU5012AF8280.00mm - 295.00mm11.02" - 11.61"

TSU9912A95290.00mm - 305.00mm11.42" - 12.00"

TSU9912110320.00mm - 335.00mm12.59" - 13.19"

TSU9912115330.00mm - 345.00mm12.99" - 13.58"

TSU9912130362.00mm - 377.00mm14.25" - 14.84"

TSU9912135370.00mm - 385.00mm14.57" - 15.16"

TSU9912140381.00mm - 396.00mm15.00" - 15.60"

TSU9912145389.00mm - 404.00mm15.31" - 15.91"

Please select your length below.