BMW Engine Parts for BMW 3 Series E92 (2007-2013)

The N54/N55 are the powerhouses of BMW, one of the most common tuning platforms, and a fan favorite for spirited driving. Being an N54/N55 owner you know that oil temps can get out of hand leaving you with an anxious feeling and the needle a little too close to the red on your gauge cluster. What if you could get the oil flowing faster, maintain lower temperatures, and still have proper engine warm-up?

Upgrade your N54/N55 engine with our Billet oil cooler housing, replacing the underperforming factory-cast aluminum unit. Engineered for enhanced performance and a blended aesthetic, our Turner oil cooler housing features an OEM+ black anodized finish and our own engineered lower-temperature thermostat. Unlike makeshift solutions like thermostat bypass kits, our housing integrates an OE thermostat, ensuring a gradual yet expedited engine warm-up process, similar to factory settings but faster.

Out goes the factory 110-degree Celsius (230F) thermostat, replaced by our 70-degree Celsius (158F) counterpart. This new thermostat triggers oil flow a significant 72 degrees Fahrenheit earlier than the factory version. This early flow translates into prolonged lower oil temperatures for both the oil cooler and engine, maintaining a happier, healthier engine with consistently lower operating temperatures.

For N54 owners seeking to use the full potential of their tuned or modified engines, our upgraded housing and thermostat are must-have additions, especially for those who frequent the track or enjoy spirited drives on winding roads. Even if you're not pushing your motor to its limits, this upgrade significantly enhances reliability. With rising oil temperatures, the risk of oil breakdown rises, resulting in compromised lubrication, more engine deposits, and increased wear over time. Our solution addresses these concerns, protecting your engine's longevity and performance, regardless of your driving style.

For vehicles equipped with the factory oil cooler, our housing offers a multitude of advantages and is a direct replacement for the OEM unit. If your vehicle lacks a factory oil cooler, this presents an ideal chance to upgrade your setup with our housing, enabling the addition of a factory cooler for enhanced performance and increased reliability. Our primary objective is to maintain optimal oil temperatures, ensuring proper lubrication for the engine's internal components, in turn prolonging their lifespan.

Features:

Thermostat - 40 degrees Celsius/ 72 degrees Fahrenheit lower than the factory unit Billet aluminum to replace the raw cast aluminum factory housing Optional cooler capability for cars without an OEM oil cooler Utilizes the lower temp thermostat to circulate oil sooner rather than an always open solution which inhibits warm-up Combine with OEM oil cooler to add cooling capacity to your FBO N54/N55 or replace the stock housing for a cooling upgrade using your existing cooler Replaceable thermostat and gaskets for easy maintenance Quick easy installation Kit Contents:

N54/N55 Billet Thermostat Housing Billet thermostat cover Low-temp thermostat Thermostat spring Housing and thermostat cover gaskets 2 Oil cooler line O-rings (17222245358) Product Development:

Our upgraded oil cooler housing was designed, engineered, tested, and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

Upgrade your engine build with Turner's WPC-treated Race Series Bearings, engineered for serious performance enthusiasts. Starting with ACL’s high-performance bearing shells, these Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Key Features:

Duraglide Tri-Metal Construction: ACL's Race Series bearings feature a high-strength overlay for enhanced performance. Optimized Oiling: Designed to promote better oil flow during high-RPM conditions. Precise Fitment: Manufactured with OEM-level precision using micron tolerance machining. WPC-Treated for Strength: Surface treatment adds strength and reduces friction for improved engine performance. No Flash Plating: Allows for better heat transfer and bearing retention. Thermal Discharge Process: Smoother, stronger components through WPC’s unique thermal discharge technology. Enhanced Heat and Friction Resistance: Built to combat the biggest enemies of high-performance engines. Don’t settle for standard bearings—choose Turner Motorsport WPC-treated Race Series Bearings for the ultimate engine performance upgrade. Perfect for your next engine rebuild or main bearing service!

Upgrade your BMW E90, E92, or E93 M3 with the Fuel Tank Breather Valve, strategically located near the fuel tank to allow pressure to escape. This essential component enhances your vehicle's performance and ensures optimal fuel system functionality.

• Compatible with BMW E90, E92, E93 M3 models
• Located near the fuel tank for efficient pressure release
• Enhances overall fuel system performance

Ensure your BMW M3 operates at its best by replacing the Fuel Tank Breather Valve, a critical component designed for optimal pressure management.

Ensure the correct voltage is being sent to/from the alternator, keep you electrical system safe from excessive voltage peaks that could cause damage to sensitive electronics and blow out fuses. Bosch's high quality unit will give you peace of mind knowing the electrical system will be safe and the voltage will remain steady. OEM replacement for BMW part # 12317561939

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This is an OEM INA Upper Idler Pulley, also known as the roller pulley or deflection pulley. The idler pulleys are known to be the primary sources for 'belt squealing'. The pulley is also encased in rubber which will crack over time. If left without service the rubber could fail completely, chucking the belt and leaving you stranded. Replacement is a very simple procedure and can be done anytime the fan is off the engine (belt replacement, water pump service, alternator replacement, etc).

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-2010 E82 BMW 135i
2011 E82 BMW 1M Coupe
2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
2007-2010 E93 BMW 335i 335is - Convertible
2004-2010 E60 BMW 535i 535xi 535i xDrive

This is an OEM INA Idler Pulley, also known as the roller pulley or deflection pulley. The idler pulleys are known to be the primary sources for 'belt squealing'. The pulley is also encased in rubber which will crack over time. If left without service the rubber could fail completely, chucking the belt and leaving you stranded. Replacement is a very simple procedure and can be done anytime the fan is off the engine (belt replacement, water pump service, alternator replacement, etc).

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-2010 E82 BMW 135i
2011 E82 BMW 1M Coupe
2006-2010 E90 BMW335i 335xi 335i xDrive - Sedan
2007-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
2007-2010 E93 BMW 335i 335is - Convertible
2004-2010 E60 BMW 535i 535xi 535i xDrive

This is an OEM INA Idler Pulley, also known as the roller pulley or deflection pulley. The idler pulley is known to be the primary sources for 'belt squealing'. The pulley is also encased in rubber which will crack over time. If left without service the rubber could fail completely, chucking the belt and leaving you stranded. Replacement is a very simple procedure and can be done anytime the fan is off the engine (belt replacement, water pump service, alternator replacement, etc).

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!