BMW Performance Clutch Kits & Parts

Give your factory clutch a heavier motorsport feel or make your extremely tough clutch more drivable! If you have an E36 there is absolutely no reason you don't have this clutch pedal! Your factory E36 clutch pedal is made of flimsy plastic with no adjustment at all, leaving you to the mercy of the clutch you have.

Our Turner Performance Adjustable Clutch Pedal is a rigid design that gives you the ability to fully adjust your clutch feel and performance. With both upper and lower adjustments this is the best pedal on the market to fine tune your clutch pedal just the way you like it. The upper eccentric provides an adjustable pedal ratio to fine tune clutch pedal effort(how heavy the pedal feels). The lower adjustment is to change the position of the clutch assist spring, this allows you to choose where the clutch assisting spring engages. Changing where the spring engages will move the area of tension on your clutch from lower, middle to higher for maximum adjustment.

Your race car no longer needs to have a clutch that makes the car undriveable on the street. Your track car can now be your daily driver or weekend cruiser.

Features:

Adjustable throw
Capable of quicker shifts
Three lower mounting points for the spring to adjust where the assistance engages
Eccentric mount for master cylinder to adjust leverage ratio and pedal feel(weight/force needed to engage the clutch)
Self lubricating bronze bushings
All necessary hardware required for installation
Pedal body and pedal are constructed from 6061-T6 aluminum and type II black anodized for a great finish
NOTE: This Clutch Pedal does not include the Compression spring and the original spring must be reused. If you'd like to purchase a new spring, please see:

35311162505 - Non-M E36 - T#64615
21522227764 - E36 M3 - T#21753

Engineered in-house, we designed this lightweight, single-mass flywheel to provide more than 10 pounds of weight savings over the factory flywheel. While some ultra-lightweight performance flywheels are manufactured from aluminum, our designers opted for a more driveable experience with steel. The mass provided by steel helps dampen vibrations and noise, delivering near-factory refinement with most of the benefits of a lightweight flywheel: quicker throttle response, improved durability (and longevity), and more effective transfer of power to the wheels.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

When it comes to selecting a clutch to pair with a lightweight flywheel, consider the driving you’ll be doing. As a single mass flywheel eliminates the dual-mass dampening of the factory flywheel, to retain the lowest noise, lowest harshness driving experience possible, select a clutch with a dampened disc such as the ACT Heavy Duty. For dedicated track cars, a solid clutch hub is appropriate.

Our recommendations:

Street: ACT Heavy Duty
Track: ACT Xtreme for high torque cars or OE 335is LuK (with 440lbs-ft or less)
Features:

Precision machined from 4140 HT heat treated chromoly steel for exceptional toughness, even wear properties, and durability.
Material quality promotes even wear across the entire friction surface
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability and elevated temperatures
Hardness improves wear characteristics
Black oxide coated for corrosion resistance on non-friction surfaces.
8620 steel pilot bearing pin, case hardened and Precision ground for maximum wear resistance.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 tested and certified to ensure safe operation under extreme operating conditions
SFI 1.1 specifies minimum material properties and requires a 3rd party lab certification test, spinning the flywheel to 1.5x redline for 1 hour to ensure the flywheel will not burst.
Specifically designed to work with N54 architecture clutches
Step height designed to optimize clamp load and maximize the usable range of clutch wear for a long service life
Performance:

Turner Flywheel 18.6 lbs
10 lbs lighter than the factory BMW flywheel (Stock Flywheel 28.9 lbs)
Faster revs
Improved throttle response
Improved acceleration
Sportier driving experience
Stock flywheel weight - 28.9lbs
Turner single mass flywheel weight = 18.55lbs

Single Mass Flywheel Conversion:

Audible chatter from the transmission after installation is considered normal. As with most single mass flywheels, there is less dampening in the flywheel to reduce "gear noise." This chatter noise may be more present when the transmission fluid temperatures are hotter and may be intensified by other modifications. Most gearboxes will experience some chatter noise at hotter temperatures. Please be advised that this noise will disappear once the clutch pedal is depressed. This symptom may be lessened by adjusting transmission fluid weight, turning off electrical/driveline consumers (A/C, High Beams, ETC.), and by raising the RPM slightly.

Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

This item fits the following BMWs with 8 bolt flywheel and build date up to 01/2009 or earlier:
2008-01/2009 E82 BMW 135i 135is 1M
2007-01/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-01/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-01/2009 E93 BMW 335i - Convertible
2008-01/2009 E60 BMW 535i 535xi 535i xDrive

Lightweight flywheel for quicker, effortless revs that improve throttle response and free up lost horsepower. Tested and approved by our engineering team at Turner Motorsport. Tested in early, late, ETA and IS model E30s for confirmed fitment.

Introducing our Turner Flywheel: an ingenious blend of lightweight design, rich features, and remarkable strength! Crafted from 4140 HT Steel, this flywheel is precision-machined from a solid piece, ensuring unmatched durability. By strategically trimming excess weight from its original design, we've achieved a significant reduction in weight, giving new life to your M20 engine. With upgraded efficiency, your M20 can now swiftly spin to high RPMs, unleashing the full power and prowess of this formidable engine. Our flywheel features a ring gear profile compatible with all starters, alongside a reference tab tailored for early cars equipped with bellhousing-mounted sensor crank position detection.

Do you have an early model transmission with the crank sensors on the bellhousing? Maybe you have a late 325is with the crank sensor on the front of the engine, or maybe you have a 1988 super ETA. No matter which E30 model you have, our flywheel is the perfect choice for you.

During the engineering process we encountered the full spectrum of M20 and flywheel combinations. Early cars with bellhousing crank sensors, late cars with front mounting crank sensors and even a super ETA. On this adventure we found both early and late single mass flywheels and even the dual mass that we thought for sure was just a myth. At first we were hesitant that we could make one flywheel to fit them all but with the persistence of our engineering team(fleet of E30 enthusiasts) we can proudly say our M20 flywheel does in fact fit all engine and transmission applications you can think of.

Features and benefits:

Fits early and late models with M20
Fits shallow and deep bellhousing transmissions
Ring gear suited for both starters (P# 12411726504 + 12411361874)
Heavier than other lightweight flywheels, lighter than OEM, its like the Goldie Locks of flywheels - its just right
Reference pin for bellhousing crank sensor
Strong Single-Piece 4140 HT Steel construction
Designed to be used with factory and OE clutches
Weight Comparisons:

​Factory single mass flywheel EARLY (11221705046) - 23.69 lbs.
Factory single mass flywheel LATE (11221706573) - 18.74 lbs.
Dual mass flywheel (21211225979) - 27.56 lbs.
Turner flywheel - 14 lbs.
What you need:

Short bellhousing transmissions (I/IS) - Throw-out bearing P# 21517521471
Tall bellhousing transmission (ETA) - Throw-out bearing P# 21511204525

Adapt an N54 or N55 GS6-53BZ transmission to your M5x/S5x engine to unlock superior torque capacity and optimized gear ratios.

Engineered for the BMW enthusiast who demands more strength and better gear ratios, the Turner Motorsport Transmission Swap Flywheel Kit provides a direct solution for mating a modern N54 or N55 6-speed gearbox to your M20, M5X, or S5X engine. This kit bridges the gap between generations, allowing you to run a high-capacity GS6-53BZ transmission without the typical fabrication nightmares.

The technical core of this kit is our dual-geometry flywheel. By utilizing this specialized design, you can retain your engine-side stock starter while using the factory clutch and throw-out bearing from your donor transmission. This ensures a precise fit and a firm, factory-like shifting feel that can handle significantly more power than older 5-speed setups. To guarantee a fitment, we’ve included a precision drill guide for bellhousing alignment and a universal pilot bearing pin to simplify the installation process.

Features and benefits:

Compatible with the starter from your original motor.
Uses factory clutch and throwout bearing from the donor transmission (GS6-53BZ).
Comes with necessary tools and a provided drill guide to adapt the top transmission mounting holes.
Kit contents:

Swap Flywheel
Pilot bearing input adapter for late N54 and N55 GS6
Drill guide, bit, and hardware.
Flywheel bolts
Optional pilot bearing
Optional clutch
Swap notes:

Fits M20/M50/M52/S50/S52/S54 engines
Needs a custom driveshaft and rear transmission mount. (We used https://www.hdtautoparts.com/driveshafts)
For E46 only: Rear transmission mount can be used from E46 330 6 Speed. Part numbers (22316760531 & 22316760532)
Installation and Support:

Click HERE for installation instructions: