BMW Engine Parts for BMW 3 Series E92 (2007-2013)

• All-in-one valve cover overhaul
• Preventative replacement saves time and trouble later on
• Includes new oil separator system
• Replace valve cover gaskets before a leak becomes worse
• Replace valve cover before it cracks

For the 2007 model year BMW switched to a plastic valve cover on the N51 and N52 engines. As we have seen over time the plastic can crack which leads to oil leaks, vacuum leaks, poor running, and other issues. Unfortunately, it's not just the gasket that needs periodic replacement but the entire valve cover itself. This kit includes a new valve cover, gaskets, eccentric shaft seal, and hardware. The valve cover also incorporates the oil separator which is not a replaceable item on its own. So a complete valve cover replacement will tackle multiple problem areas at once. The valve cover is the same for N51 SULEV and N52 engines.

Cracked Valve Cover. The plastic used for the N52 valve cover is thin and weak in certain spots. This makes it prone to hairline or larger cracks that will leak oil and cause vacuum leaks. You might also notice rough running, especially at idle. Often a technician will go looking for a failed ignition coil, spark plug, or failed vacuum hose on the engine. And without a fault code to assist in diagnosis this can often mean wasted time and money. A cracked valve cover is a new problem area that many techs don't think to check.

Oil Separator/Crankcase Vent. BMW integrated the oil separator system into the valve cover on these later engines. An internal manifold creates a cyclone effect and centrifugal force separates vapor from the liquid oil. The liquid oil is supposed to drain through the valve cover and back to the oil pan while the remaining vapor is burned up during combustion. It's a very efficient and environmentally-friendly design with very few moving parts. Unfortunately it's not perfect and eventually the internal passageways will become clogged. This problem is made worse in cars that have short drive cycles, sit for long periods of time, do not have frequent oil changes, do not see regular runs to redline, and cars in freezing climates. If the engine never reaches optimal operating temp the oil remains in liquid form or becomes sludge. This is bad news for the entire engine, leading to fouled spark plugs, rough running and misfires and even premature failure of catalytic converters and oxygen sensors. Since the oil separator system in the valve cover is not available on its own, and cleaning it is nearly impossible, the complete replacement of the valve cover is the only option. Other oil vent tubes and vacuum hoses are also recommended to get replaced at the same time.

Valve Cover Gaskets. As with any rubber part, failures occur when the rubber becomes dry and brittle. The pliable rubber no longer forms a seal between the cylinder head and valve cover where it will develop an oil leak. Valve cover gaskets that leak can allow oil to seep into the spark plug holes and contaminate ignition coil boots and plugs. That can lead to rough running and misfires. A new valve cover includes new gaskets.

Eccentric Shaft Seal. The seal for the eccentric shaft sensor is a known spot for oil leaks. When the seal to the valve cover fails oil can end up in the sensor itself and ruin the sensor (an unecessary $300 expense). Usually a new seal (o-ring) will stop the leaks but sometimes the valve cover is at fault too. A new eccentric shaft seal is included.

All new hardware is included to avoid re-using and over-tightening the original bolts (they have a very low torque rating).

Replacement requires accessing the rear of the engine with a lot of the upper plastic shrouding removed. The vent hose on the valve cover should be replaced as it is almost always broken anyway (#11157559528). The metal fuel line must also be removed and disconnected from the fuel injectors. Professional installation is encouraged if you have never done this kind of work before. Serious DIY types should have a Bentley Service Manual to use which greatly explains the process. You may also want to combine this work with the oil filter housing gasket replacement.

There is no maintenance or replacement interval for the N52 valve cover. However, we have seen cracks and other failures in the 50,000-90,000 mile range. Our best advice is to plan on a major top end overhaul around the 70-80,000 mile mark. There's no mechanical downside to replacing it as prevention and it will make the engine run better and last longer.

This item fits the following BMWs:
2008-2012 E82 BMW 128i
2007-2011 E90 BMW 328i 328xi 328i xDrive - Sedan
2007-2012 E91 BMW 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2008-2010 E60 BMW 528i 528xi 528i xDrive
2011 F10 BMW 528i
2007-2010 E83 BMW X3 3.0i X3 3.0si
2007-2008 E70 BMW X5 3.0si
2007-2008 E85 BMW Z4 3.0i Z4 3.0si
2009-2010 Z4 BMW Z4 sDrive30i

Enhance the electrical system of your BMW with the Genuine BMW E9X Rep. Wiring Harness, Strut S - 61129206018. This genuine BMW part ensures optimal performance and reliability, providing a seamless replacement for your vehicle's wiring harness.

• Genuine BMW part for guaranteed compatibility and reliability
• Designed to meet BMW's strict quality standards
• Ensures proper electrical connections and functionality
• Easy installation with precise fitment

BMW S65 BE Bearings Connecting Rod Bearing Upgrade Set is designed to address the known flaws in the factory BMW rod bearings, particularly for the S65B40 engine. Manufactured by Clevite to BE Bearing specifications, this set provides a crucial upgrade with its enhanced materials and design, ensuring improved performance and durability.

The original BMW bearings have minimal clearance, which leads to premature wear and potential engine failure. This upgrade replaces the tin-aluminum factory bearings with a superior silver-oxide-coated tri-metal "F" series design. The new bearings can handle 30% more load, offer better performance in low oil conditions, and are more forgiving of foreign particles in the oil. Designed specifically for BMW S65 engines, these bearings provide optimal performance for high-horsepower applications.

• Designed specifically for BMW S65B40 engines
• Silver-oxide coating withstands 30% more load capacity
• Improved performance under low-oil and boundary conditions
• Stronger backing material for enhanced durability
• Corrects factory BMW rod bearing clearance issue
• Ideal for high-horsepower applications and factory 10W60 weight oils
• Complete set for 8 cylinders, ready for installation

Fits the following BMWs:

• 2008-2013 E9X BMW M3 (S65)

Rubber engine and transmission mounts for a street car and solid aluminum for the track, right? Well, it's not that straightforward anymore.

Stock rubber fluid-filled mounts are designed to be soft and comfortable, limiting the NVH (noise, vibration, and harshness) felt by the driver. The drawback inherent with a conventional design is driveline deflection, making it more difficult to put the power to the wheels, as well as making a money-shift or miss-shift more likely as they age. Solid mounts are exactly the opposite of this - they permit tons of NVH while offering zero deflection, making these a must have for track-driven vehicles looking to capitalize on every ounce of performance available. Enthusiasts looking to find the best of both worlds often look to polyurethane engine mounts - and many are disappointed with other designs on the market. Seeking a mount that offers a positive connection yet doesn't deform, fail, or rattle the fillings out of their mouths is frequently a lost cause.

Until now. 

We engineered these mounts with these very concerns in mind. We know if a soft mount offers a sloppy connection it doesn't work on the track, and a solid mount isn't acceptable as a daily driver (for most!) and set out to engineer a mount that would meet the needs for both. At the core of our enclosed design is a partially-constrained, multi-piece polyurethane bushing with precisely-set preload. This architecture absorbs and disperses resonant engine frequencies as opposed to amplifying them (like some other designs do), which results in a positive-connection, enthusiast-feel mount with the vibration. Understanding that heat is a concern for the passenger side mount's close proximity to the exhaust, we utilize a PEEK thermal insulation plate to greatly reduce heat transfer to the polyurethane, making heat a non-issue for these mounts. 

We offer two durometers, with both densities offering similar "positive connection" feeling. 60A is slightly softer and offers more of a stock feel, while 80A delivers a little more engine "feel" while under acceleration. 

Product features and benefits:

• Crisper throttle response, positive shifter location, direct power transfer
• High quality polyurethane offered in both 60A & 80A durometers (rebuildable, too)
• Resistant to water, ozone, and chemicals, maintaining its resiliency and elasticity longer than conventional rubber.
• Precision machined billet 6061-T6 aluminum housing, black anodized for durability and corrosion resistance. Grade 10.9 stud - fear not, big turbo owners.
• Thermal isolation spacer on the hot side to resist heat transfer into the poly
• Engineered in-house and made in America

*Still require a solid mount? Turner Motorsport solid engine and transmission mounts for N52/N54/N55 coming early July 2017.

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335d 335i 335xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is