BMW Brakes & Brake Parts for BMW 3 Series E92 (2007-2013)

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Turner has developed a zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

When replacing your worn out brakes, the market is flooded with performance options. If your BMW doesn't see track time, it's not very practical. Performance pads and rotors tend to result in a lack of bite at low braking temperatures and cause excessive noise in daily driven vehicles that becomes irritating. BMW brakes from the factory are perfectly suited for trips around town, across the country, and even the occasional spirited driving session, delivering smooth, quiet, and long lasting performance. 

Included in this E9X BMW brake package are all of the OEM equivalent components needed to replace your Front brakes with comfort, reliability, and optimal lifespan in mind.

Brake components in this kit:

• Pagid Front Brake Pads
• Zimmerman Front Rotors
• New Front Wear Sensors
• Brand New Stainless Steel Set Screws
• Syl-Glide Silicone Brake Lubricant 

Fits the following BMWs:
2006-2013 E9X BMW M3
2011-2012 E82 BMW 1M

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner Stainless brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

When replacing your worn out brakes, the market is flooded with performance options. If your BMW doesn't see track time, it's not very practical. Performance pads and rotors tend to result in a lack of bite at low braking temperatures and cause excessive noise in daily driven vehicles that becomes irritating. BMW brakes from the factory are perfectly suited for trips around town, across the country, and even the occasional spirited driving session, delivering smooth, quiet, and long lasting performance. 

Included in this E9X BMW brake package are all of the OEM equivalent components needed to replace your Front and Rear brakes with comfort, reliability, and optimal lifespan in mind.

Brake components in this kit:

• Akebono Euro Front & Rear Brake Pads
• Zimmerman Front & Rear Rotors
• New Front & Rear Wear Sensors
• Brand New Stainless Steel Set Screws
• Syl-Glide Silicone Brake Lubricant 

Fits the following BMWs:
2006-09/2007 E9X BMW 325i 328i

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

These 2-piece floating rotors help dissipate heat better than a standard cast iron rotor and are also lighter for less unsprung weight. Managing heat in the brake system is vital to braking performance, especially on the track or when driven hard. It's why your brake rotors have internal vanes that vent heat as the rotor spins. These 2-piece ECS rotors feature an outer cast iron friction surface ring that is separate from the aluminum center hat. This allows better airflow through the vanes and for the friction ring can expand as it gets hot. The rotors are also cross-drilled for better ventilation and slotted to improve brake pad performance.

ECS 2-Piece Rotors feature:

• Aluminum hats for light weight
• Heat-treated cast iron friction rings
• 2-piece assembly improves brake cooling
• Anti-corrosion coating on non-friction surfaces and hard anodizing on rotor hat

These are the same size as the stock rotors so your stock caliper and mounting bracket will fit and there will be no clearance issues with your wheels or to other components. Stainless steel rotor retaining screws are included. You can use these with any brake pad.

Price is for the pair of brake rotors.

This item fits the following BMWs:
2008-2013 E82 E88 BMW 135i

Fits the following with M Performance Brakes:
2006-2011 E90 BMW 325i 328i 330i - Sedan
2007-2011 E91 BMW 325i 328i - Touring Wagon
2007-2013 E92 BMW 328i - Coupe
2007-2013 E93 BMW 328i - Convertible

These 2-piece floating rotors help dissipate heat better than a standard cast iron rotor and are also lighter for less unsprung weight. Managing heat in the brake system is vital to braking performance, especially on the track or when driven hard. It's why your brake rotors have internal vanes that vent heat as the rotor spins. These 2-piece ECS rotors feature an outer cast iron friction surface ring that is separate from the aluminum center hat. This allows better airflow through the vanes and for the friction ring can expand as it gets hot. The rotors are also cross-drilled for better ventilation and slotted to improve brake pad performance.

ECS 2-Piece Rotors feature:

• Aluminum hats for light weight
• Heat-treated cast iron friction rings
• 2-piece assembly improves brake cooling
• Anti-corrosion coating on non-friction surfaces and hard anodizing on rotor hat

These are the same size as the stock rotors so your stock caliper and mounting bracket will fit and there will be no clearance issues with your wheels or to other components. Stainless steel rotor retaining screws are included. You can use these with any brake pad.

Price is for the pair of brake rotors.

This item fits the following BMWs:
2011 E82 E88 BMW 1M Coupe
2008-2013 E90 E92 E93 BMW M3 Sedan, Coupe, Convertible

These 2-piece floating rotors help dissipate heat better than a standard cast iron rotor and are also lighter for less unsprung weight. Managing heat in the brake system is vital to braking performance, especially on the track or when driven hard. It's why your brake rotors have internal vanes that vent heat as the rotor spins. These 2-piece ECS rotors feature an outer cast iron friction surface ring that is separate from the aluminum center hat. This allows better airflow through the vanes and for the friction ring can expand as it gets hot. The rotors are also cross-drilled for better ventilation and slotted to improve brake pad performance.

ECS 2-Piece Rotors feature:

• Aluminum hats for light weight
• Heat-treated cast iron friction rings
• 2-piece assembly improves brake cooling
• Anti-corrosion coating on non-friction surfaces and hard anodizing on rotor hat

These are the same size as the stock rotors so your stock caliper and mounting bracket will fit and there will be no clearance issues with your wheels or to other components. Stainless steel rotor retaining screws are included. You can use these with any brake pad.

Price is for the pair of brake rotors.

This item fits the following BMWs:
2011 E82 E88 BMW 1M Coupe
2008-2013 E90 E92 E93 BMW M3 Sedan, Coupe, Convertible