Turner Motorsport for BMW 3 Series E92 (2007-2013)

Rubber engine and transmission mounts for a street car and solid aluminum for the track, right? Well, it's not that straightforward anymore.

Stock rubber fluid-filled mounts are designed to be soft and comfortable, limiting the NVH (noise, vibration, and harshness) felt by the driver. The drawback inherent with a conventional design is driveline deflection, making it more difficult to put the power to the wheels, as well as making a money-shift or miss-shift more likely as they age. Solid mounts are exactly the opposite of this - they permit tons of NVH while offering zero deflection, making these a must have for track-driven vehicles looking to capitalize on every ounce of performance available. Enthusiasts looking to find the best of both worlds often look to polyurethane engine mounts - and many are disappointed with other designs on the market. Seeking a mount that offers a positive connection yet doesn't deform, fail, or rattle the fillings out of their mouths is frequently a lost cause.

Until now. 

We engineered these mounts with these very concerns in mind. We know if a soft mount offers a sloppy connection it doesn't work on the track, and a solid mount isn't acceptable as a daily driver (for most!) and set out to engineer a mount that would meet the needs for both. At the core of our enclosed design is a partially-constrained, multi-piece polyurethane bushing with precisely-set preload. This architecture absorbs and disperses resonant engine frequencies as opposed to amplifying them (like some other designs do), which results in a positive-connection, enthusiast-feel mount with the vibration. Understanding that heat is a concern for the passenger side mount's close proximity to the exhaust, we utilize a PEEK thermal insulation plate to greatly reduce heat transfer to the polyurethane, making heat a non-issue for these mounts. 

We offer two durometers, with both densities offering similar "positive connection" feeling. 60A is slightly softer and offers more of a stock feel, while 80A delivers a little more engine "feel" while under acceleration. 

Product features and benefits:

• Crisper throttle response, positive shifter location, direct power transfer
• High quality polyurethane offered in both 60A & 80A durometers (rebuildable, too)
• Resistant to water, ozone, and chemicals, maintaining its resiliency and elasticity longer than conventional rubber.
• Precision machined billet 6061-T6 aluminum housing, black anodized for durability and corrosion resistance. Grade 10.9 stud - fear not, big turbo owners.
• Thermal isolation spacer on the hot side to resist heat transfer into the poly
• Engineered in-house and made in America

*Still require a solid mount? Turner Motorsport solid engine and transmission mounts for N52/N54/N55 coming early July 2017.

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335d 335i 335xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

These aluminum pedals were designed with one thing in mind -- performance. We wanted a pedal set that gave us the grip EXACTLY where we wanted it: MASSIVE GRIP on the brake and clutch pedals, and far less grip on the accelerator to allow the right foot to better slide/move during heal-toe braking. This set surpasses all others in this area, giving your BMW's foot operated controls a more tactile feel and response. The brake and clutch pedals feature pyramid shaped spikes, which actually BITE the soles of your shoes PERFECTLY, creating the ultimate (and unbeatable) friction surface.

These pedals are 100% MADE IN THE USA, and are CNC machined from aircraft quality aluminum billet to perfectly fit your BMW. There's no rubber to wear out, and no cosmetic finishes to chip or flake off. Stainless steel hardware is included, as well as a basic installation guide (professional installation always recommended). These pedals are for left-hand drive (LHD), manual transmission BMWs only (including SMG and DCT sequential manual gearboxes -- on these cars, you will only use one of the included clutch/brake sized pedals).

Now available in (optional) black anodized! The same shoe-gripping performance as our standard "naked" aluminum racing pedals, but with an added black anodized coating, for a stealth black finish. We always recommend the naked metal pedals for harsher/race type use, as all cosmetic finishes will eventually degrade over time. But for those looking for the black-out look, we can now accommodate! To add this option, simply choose your selection below.

Enhance the performance of your BMW E9X M3 with the BMW E9X M3 Turner Motorsport S65 Power Pulley Kit. This high-quality power pulley kit from Turner Motorsport is designed specifically for the S65 engine, providing increased power and torque for a more exhilarating driving experience. With easy installation and durable construction, this kit is a must-have upgrade for BMW enthusiasts.

• Increases power and torque for improved performance
• Designed specifically for the S65 engine in BMW E9X M3 models
• Easy installation with included instructions
• Durable construction ensures long-lasting reliability

BMW’s are known to have failure prone front thrust arm bushings.  The flexible rubber bushings, even those found in M performance models, allow significant movement of the front wheels to maximize daily driving comfort, but also allow considerable alignment change.  This results in a disconnected and numb road feel, standing between you and a confidence inspiring driving experience.  Eventually the fluid filled rubber bushings fatigue and crack due to continual deflection and ozone degradation, and eventually the damping fluid leaks out resulting in complete failure. 

For the enthusiast looking for superior performance and longevity with a crisp, confidence-inspiring driving experience, our sealed ball joint monoballs are the best solution available!  Our experience with spherical front control arm ball joints go back to those we designed and used in our IMSA E90 328i and E92 M3 racecars (GS class Champions in 2011).  We wanted to offer E31, E32, E34, E38, E39, E53, E60, E63, E64, and E83 owners similar levels of handling precision and control for the track and street. 

The bearing housing is precision CNC machined from 6061-T6 anodized aluminum and features a knurled OD to ensure a perfect press fit, and utilize a sealed OEM BMW ball joint for exceptional quality and durability, making them completely at home on both the street and track with no compromise.  We have done extensive street, autocross, and track testing to ensure the ball joint used in this bushing design excels in each setting.  The advantage of a sealed ball joint is that it eliminates all unwanted deflection while still allowing complete bind-free movement throughout suspension travel, resulting in exceptional control of wheel alignment.  What you get is superior steering precision, turn-in response, direct braking feedback, and better handling.

In short, if you're seeking the ultimate in precise, predictable handling and control, with crisp braking response and a long service life that’s equally at home on the street or track - look no further. We have you covered.

Watch to learn more about Turner Monoball Bushings

We offer these thrust arms with the monoball bushings pre-installed for your convenience. Since BMW recommends the control arms be replaced for every other bushing change, we prefer to sell these as a pre-assembled set. The bushings are also available pre - installed if you want to avoid having these pressed in.

*Installation instructions*

Features:

Bearing housing

• Precision CNC machined from 6061-T6 blue anodized aluminum
• Knurled OD to provide the perfect fit for the wide range of thrust arm bore diameters among brands.
• CNC machined 304ss ball joint sleeve inserts, providing a precision fit between the ball joint and the subframe. 

Bearing

• OEM BMW sealed and greased ball joint for exceptional durability and service life.

Performance

• Nearly instantaneous, crisp steering and braking response.
• Maintenance free, long lasting performance. 
• Improved road feel without undesirable NVH.

This item fits the following AWD BMWs:
2006-2011 E90 BMW 325i 328i 330i 335i - Sedan AWD
2006-2011 E91 BMW 328i - Wagon AWD
2007-2012 E92 BMW 328i 335i 335is - Coupe AWD
2013-2015 E84 BMW X1 xDrive28i X1 xDrive35i 
 

Set of 4 universal 2.5" inlet to 3.5" outlet exhaust tips.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

Swivel feature for perfect alignment of the exhaust tips in the rear bumper
2.5" Inner Diameter
3.5" Outer Diameter
Black Chrome
Double Wall Construction
Angle Cut Style
Includes Stainless Steel Clamp

The factory BMW S65 dual-mass flywheel is engineered with comfort in mind, catering to the luxury-oriented expectations of the brand’s driving experience. Its design focuses on dampening drivetrain vibrations, smoothing out gear transitions, and minimizing harshness during operation. However, this refinement costs valuable performance. The dual-mass flywheel adds a substantial 27 lbs of rotational mass to the drivetrain, which significantly hinders throttle response and makes rev-matching feel sluggish and disconnected. Moreover, dual-mass flywheels are notorious for being a weak link in modified or high-performance builds and can prove costly to replace when they inevitably fail.

Our Single-Mass Lightweight Flywheel Conversion addresses all of these shortcomings with a purpose-built, lightweight, single-mass design that prioritizes performance. Weighing in at only 19 lbs., this design significantly reduces rotational mass, allowing your S65 to achieve its true motorsport potential!

Features & Benefits:

Precision machined from 4140 HT heat-treated chromoly steel for exceptional toughness, even wear properties, and increased durability.
Material quality promotes even wear across the entire friction surface, prolonging component lifespan.
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability.
Hardness improves component wear characteristics.
Black oxide coated for corrosion resistance on non-friction surfaces.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
Specifically designed to work with S65 OE-architecture clutches.
Optimized step height maximizes clutch clamp load and offers a prolonged service life.
Performance:

8 lbs. lighter than the factory BMW flywheel!
OEM Dual-Mass: 27 lbs.
Turner Motorsport Single-Mass: 19 lbs.
Faster revs
Improved throttle response and acceleration
Allows for a more engaging driving experience and delivers a feeling of direct connection
Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

Full carbon fiber intake to increase flow, performance and aesthetics! Dual inlet design for maximized air flow while retaining the OEM+ fitment.

The most common N55 intake utilizes a short plastic tube and oversized cone filter; it is your job to have better taste than the common N55 owner. This carbon intake changes the whole image of the N55 engine while maintaining a flow of cool air and added induction noise. With a dual inlet design the engine bay retains its functionality while adding a second inlet to provide your engine with improved air flow and sound. To ensure the engine gets the coolest air possible the second inlet is located in the "sweet spot" on the cold side of the engine for the lowest intake air temps and most air flow possible. The cone filter features a bellmouth velocity stack filter that creates the satisfying flutter after letting of the throttle.

Our Turner Carbon Fiber Intakes start with a 3D scan of the factory intake and engine bay. Engineers use the 3D imaging of the chassis to design the intake in SolidWorks modeling software. Using a Flow Bench, the Intake is then airflow tested against the factory intake, to ensure optimal airflow improvement against stock. The final product is a beautiful and functional Carbon Fiber Intake, CAD designed for perfect integration with the OEM inlet ducting and stock mounting locations and proven to flow better than factory.

Key Benefits:

Increased flow over the factory intake
Carbon fiber airbox and intake tube with gloss clear coat for UV protection
CAD-Designed for perfect Integration
Custom high flow air filter specially designed to to pair with the carbon fiber airbox
Kit Contents:

Carbon Intake Tube
Full Carbon 2 Piece Airbox
Bellmouth Velocity Stack Cone Filter
Billet Turbo Inlet Adapter
Silicone Coupler
Hardware For Installation
Design:

- Carbon Fiber Intake Tube

Carbon inlet tube featuring a smoother interior without corrugations for a smooth flow path.
Integrated carbon flange allows secure mounting of the tube to the carbon air boxes.
Intake tube is manufactured using 2x2 twill weave carbon fiber for a great look in the engine bay.
Gloss finish clear coat for UV protection.
4-ply reinforced silicone coupler and 6061-T6 black anodized aluminum flange that utilizes the factory o-ring and retaining clip.
- Air Box

Carbon fiber airboxes are manufactured using 2X2 twill weave carbon fiber and protected with a gloss finish clear coat for UV resistance to match the intake tube.
Air box mounts in stock location with supplied hardware.
- Air Filter

Conical hi-flow reusable air filter; featuring 8 ply oiled cotton gauze construction to maximize filtration efficiency.
Bellmouth (velocity stack) filter flange inlet to reduce turbulence in order to maximize flow.
Product Development:

Turner N55 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.

Fitment:

E82 135i N55
E88 135i N55
E84 X1 35i
E90 335/xi N55
E92 335/xi N55
E93 335/xi N55

New to our line of exceptional performance upgrades for your BMW, the Turner Motorsport E9X M3 (S65) Valved Axle-back exhaust system is here to improve your driving experience with hearty exhaust notes and a noticeable bump in performance. With the muffler valves closed, this exhaust is quite unassuming. When you open up the valves, using the supplied valve controller, this exhaust transforms your car, giving your car a menacing growl!

Now, we get it, not everyone can, or wants to delete their factory cats. Whether it be emissions testing or a check engine light, the smell of unfiltered exhaust, the very aggressive sound, or warranty reasons. Whatever the reason, We've got you covered! This exhaust setup leaves all 4 factory cats in place, making it 100% emissions legal for everyone, even California!

This exhaust sports Mandrel bent dual 2.5” 304SS pipes with a brushed finish, with exhaust gases flowing through efficient piping to High flow, valved, stainless steel mufflers. Designed to mount with the factory exhaust hangers, this exhaust is a bolt-on replacement for the OE version. To help reduce the time you spend under the car installing the system, Accuseal slip-fit joints are included to make fitment as easy as possible. The Turner Motorsport full exhaust system includes a High flow, valved, stainless-steel muffler and is available as an Axle Back, Cat-back system, as well as a full Turbo back system.

Give your M3 the dual-purpose exhaust system that satisfies both your neighbors and your need for sound with the Turner Motorsport E9X M3 full exhaust system!

Kit Includes:

Turner Axle back Exhaust with X pipe
Turner Adapter pipes for Factory Mid Pipes
Turner Muffler Valve Controller Kit
Turner Engraved Exhaust Tips
Features:

Mandrel bent dual 2.5” 304SS pipe with brushed finish
Turner Engraved Brushed exhaust tips
High flow, valved, stainless steel mufflers
Accuseal slip fit joints for easy fitment
Utilizes factory exhaust hangers

Upgrade your engine build with Turner's WPC-treated Race Series Bearings, engineered for serious performance enthusiasts. Starting with ACL’s high-performance bearing shells, these Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Key Features:

Duraglide Tri-Metal Construction: ACL's Race Series bearings feature a high-strength overlay for enhanced performance. Optimized Oiling: Designed to promote better oil flow during high-RPM conditions. Precise Fitment: Manufactured with OEM-level precision using micron tolerance machining. WPC-Treated for Strength: Surface treatment adds strength and reduces friction for improved engine performance. No Flash Plating: Allows for better heat transfer and bearing retention. Thermal Discharge Process: Smoother, stronger components through WPC’s unique thermal discharge technology. Enhanced Heat and Friction Resistance: Built to combat the biggest enemies of high-performance engines. Don’t settle for standard bearings—choose Turner Motorsport WPC-treated Race Series Bearings for the ultimate engine performance upgrade. Perfect for your next engine rebuild or main bearing service!