BMW Sway Bar Kits

These adjustable rear links are only required when using sway bar / swaybars with a suspension with a very low ride height, where it may be necessary to adjust the length of the end links for proper sway bar clearance from the drive axles or other suspension components. These suspensions are usually found only on race cars but this may also apply to street cars with sport springs/sport coil overs that are lowered a lot. On most street cars lowered 1.5" or less, the stock links will be fine.

These end links feature a Heim joint, which allows enough lateral movement when disconnected to adjust the length of the link without removing the entire link from the car. This is particularly helpful when eliminating or adjusting preload while tuning the suspension. Similar links without this joint, can't be adjusted without totally removing the link from the car.

Built-in grease fittings allow for occasional lube, and a packet of grease is included. These links are sold as a set, and include two end links and hardware for H&R and TMS sway bars (other brands may not need the hardware). 

At their shortest setting they are 2.875" hole to hole and on their longest setting they are 3.5" hole to hole.

*Note: these links will not work with factory or non-adjustable Eibach sway bars.

NOW LOCATED UNDER T#338370

Improve your BMW E46 M3's balance and performance with Turner Motorsport sway bars, meticulously designed to outperform stock anti-roll bars. These bars effectively reduce body roll, minimizing the understeering effects associated with staggered wheel setups. Featuring adjustability with a 3-position front and 2-position rear settings, these bars cater to both street and track handling needs. Sized at 30mm in the front and 25mm in the rear (+4mm and +3.5mm from stock, respectively), Turner bars are crafted from robust spring steel for superior strength and resilience. Shot peened, heat-treated, and precision forged, these bars promise exceptional durability.

Product Benefits:

• Reduces body roll for enhanced stability
• Minimizes understeering effects of staggered wheel setups
• Adjustable settings for optimized street and track handling
• Crafted from robust spring steel for superior strength
• Shot peened, heat-treated, and precision forged for durability

You get the best of both worlds with this pair of Turner Motorsport adjustable sway bar links. We searched far and wide to find the hidden gem of swaybar links. You get the same quiet operation and long life as the stock links plus the strength and adjustability of rod-end style sway bar links.

With the wide range of suspensions and sway bars available today adjustable sway bar links can help you with many problems. Along with the ability to remove preload you can change the length to maximize sway bar geometry. Example: if the sway bar hoop comes too close to the steering rack, oil cooler, or under tray in its suspension travel you can adjust it by simply lengthening or shorting the adjustment rod. In some cases you may need a longer or shorter adjustment rod to achieve optimal geometry. We also offer these same links in other custom lengths (click here) that may not be specific to BMW chassis.

Features:

• Adjustable to neutralize preload on sway bar (balanced handling)
• The ability to set sway bar geometry and clearance
• Low friction ball joints
• High articulation
• Direct replacement for OEM sway bar links
• Watertight boot seal
• Ball joint is made by a world leader in ball joint technology, THK. THK's OEM Customers: BMW, Porsche, Ford, GM, Nissan, Honda, and Toyota

Turner Swaybar Link Specs:
TSU9912AF1: 220.00mm - 235.00mm / 8.66" - 9.25"
TSU4612AF3: 250.00mm - 265.00mm / 9.84" - 10.43"
TSU5012AF8: 280.00mm - 295.00mm / 11.02" - 11.61"
TSU9912A95: 290.00mm - 305.00mm / 11.42" - 12.00"

These adjustable sway bar end links can be used on a variety of BMWs. Please select your car below. Please note these end links do not fit non-M E36, except 325i/is produced before 6/1992.

Sway bar end links connect the swaybar to the rest of the suspension, preventing body roll and keeping everything in line in tight turns. This exposes these links to a high amount of stress and pressure, often leading to split bushings and sloppy body control and knocking noises. 

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Genuine BMW Rear Swing Support -
This item fits the following BMW Chassis:
F01,F02,F06,F10,F12,F13

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to address this common issue with Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. These end links feature a bolt-through bushing design, which is compatible with most adjustable aftermarket sway bars. Mounting hardware is included for easy installation.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits most aftermarket sway bars with bolt-through attachment Laser-etched markings for quick and easy adjustments