BMW Performance Clutch Kits & Parts

Give your factory clutch a heavier motorsport feel or make your extremely tough clutch more drivable! If you have an E36 there is absolutely no reason you don't have this clutch pedal! Your factory E36 clutch pedal is made of flimsy plastic with no adjustment at all, leaving you to the mercy of the clutch you have.

Our Turner Performance Adjustable Clutch Pedal is a rigid design that gives you the ability to fully adjust your clutch feel and performance. With both upper and lower adjustments this is the best pedal on the market to fine tune your clutch pedal just the way you like it. The upper eccentric provides an adjustable pedal ratio to fine tune clutch pedal effort(how heavy the pedal feels). The lower adjustment is to change the position of the clutch assist spring, this allows you to choose where the clutch assisting spring engages. Changing where the spring engages will move the area of tension on your clutch from lower, middle to higher for maximum adjustment.

Your race car no longer needs to have a clutch that makes the car undriveable on the street. Your track car can now be your daily driver or weekend cruiser.

Features:

Adjustable throw
Capable of quicker shifts
Three lower mounting points for the spring to adjust where the assistance engages
Eccentric mount for master cylinder to adjust leverage ratio and pedal feel(weight/force needed to engage the clutch)
Self lubricating bronze bushings
All necessary hardware required for installation
Pedal body and pedal are constructed from 6061-T6 aluminum and type II black anodized for a great finish
NOTE: This Clutch Pedal does not include the Compression spring and the original spring must be reused. If you'd like to purchase a new spring, please see:

35311162505 - Non-M E36 - T#64615
21522227764 - E36 M3 - T#21753

If you've ever bled the clutch hydraulic system on your BMW, you know how frustrating it can be. Designed with both DIY enthusiasts and professional technicians in mind, our clever tool simplifies one of the most notoriously annoying steps in clutch service.

Crafted from high-quality aluminum and finished in a durable black anodized coating, our clutch slave cylinder bleeder tool is built to last. Its function is simple: the adjustable piston rod applies controlled pressure directly to the clutch slave cylinder’s piston, compressing it and reducing its internal volume. By minimizing the amount of air trapped inside the cylinder, bleeding becomes faster, cleaner, and far more effective—no more endless pedal pumping or inconsistent clutch feel. The result is firm, consistent clutch pedal engagement and a smoother overall driving experience, all achieved with less time and effort underneath the car.

FEATURES & BENEFITS

Simplifies bleeding the BMW clutch hydraulic system by reducing trapped air in the slave cylinder Eliminates excessive pedal pumping and inconsistent clutch feel Helps achieve firm, consistent clutch pedal engagement Crafted from high-quality aluminum for strength and longevity Durable black anodized finish resists wear and corrosion Designed for both DIY enthusiasts and professional technicians PRODUCT DEVELOPMENT

Our Clutch Slave Cylinder Bleeder Tool was designed, engineered, tested, and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology, including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

Engineered in-house, we designed this lightweight, single-mass flywheel to provide more than 10 pounds of weight savings over the factory flywheel. While some ultra-lightweight performance flywheels are manufactured from aluminum, our designers opted for a more driveable experience with steel. The mass provided by steel helps dampen vibrations and noise, delivering near-factory refinement with most of the benefits of a lightweight flywheel: quicker throttle response, improved durability (and longevity), and more effective transfer of power to the wheels.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

When it comes to selecting a clutch to pair with a lightweight flywheel, consider the driving you’ll be doing. As a single mass flywheel eliminates the dual-mass dampening of the factory flywheel, to retain the lowest noise, lowest harshness driving experience possible, select a clutch with a dampened disc such as the ACT Heavy Duty. For dedicated track cars, a solid clutch hub is appropriate.

Our recommendations:

Street: ACT Heavy Duty
Track: ACT Xtreme for high torque cars or OE 335is LuK (with 440lbs-ft or less)
Features:

Precision machined from 4140 HT heat treated chromoly steel for exceptional toughness, even wear properties, and durability.
Material quality promotes even wear across the entire friction surface
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability and elevated temperatures
Hardness improves wear characteristics
Black oxide coated for corrosion resistance on non-friction surfaces.
8620 steel pilot bearing pin, case hardened and Precision ground for maximum wear resistance.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
SFI 1.1 tested and certified to ensure safe operation under extreme operating conditions
SFI 1.1 specifies minimum material properties and requires a 3rd party lab certification test, spinning the flywheel to 1.5x redline for 1 hour to ensure the flywheel will not burst.
Specifically designed to work with N54 architecture clutches
Step height designed to optimize clamp load and maximize the usable range of clutch wear for a long service life
Performance:

Turner Flywheel 18.6 lbs
10 lbs lighter than the factory BMW flywheel (Stock Flywheel 28.9 lbs)
Faster revs
Improved throttle response
Improved acceleration
Sportier driving experience
Stock flywheel weight - 28.9lbs
Turner single mass flywheel weight = 18.55lbs

Single Mass Flywheel Conversion:

Audible chatter from the transmission after installation is considered normal. As with most single mass flywheels, there is less dampening in the flywheel to reduce "gear noise." This chatter noise may be more present when the transmission fluid temperatures are hotter and may be intensified by other modifications. Most gearboxes will experience some chatter noise at hotter temperatures. Please be advised that this noise will disappear once the clutch pedal is depressed. This symptom may be lessened by adjusting transmission fluid weight, turning off electrical/driveline consumers (A/C, High Beams, ETC.), and by raising the RPM slightly.

Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

This item fits the following BMWs with 8 bolt flywheel and build date up to 01/2009 or earlier:
2008-01/2009 E82 BMW 135i 135is 1M
2007-01/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-01/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-01/2009 E93 BMW 335i - Convertible
2008-01/2009 E60 BMW 535i 535xi 535i xDrive

BMW E30 M20 Clutch And Flywheel Kit - I/IS from Turner Motorsport offers a premium upgrade for naturally aspirated M20 engines. This comprehensive kit includes a lightweight single-mass flywheel and a Sachs clutch kit, providing a significant performance boost and refreshing the driving experience of early and late-model E30s.

• Lightweight Single-Mass Flywheel: Enhances throttle response and frees up lost horsepower by reducing rotating mass. Provides a perfect balance between lightweight performance and durability.
• Sachs OE Replacement Clutch Kit: Includes clutch disc, pressure plate, throw-out bearing, and pilot bearing, designed for reliable performance and smooth operation.
• Improved Driving Experience: Refreshes the clutch pedal feel and driving dynamics of the M20 engine, ideal for both early and late model E30s.
• Quality and Fitment: Tested and approved by Turner Motorsport for optimal performance and confirmed fitment on various E30 models.
• Additional Components: Recommended transmission seals, fluid, and mounting hardware available separately for a complete service.

Lightweight single mass flywheel paired with the Sachs clutch kit, perfect for naturally aspirated M20's! Fits early and late model cars.

A perfect upgrade and refreshment for your M20! Free up lost horsepower with the lightened single mass flywheel and get back the life in your clutch pedal. This kit is put together with the idea of an OEM+ upgrade, perfect for people looking to refresh the driving experience of their M20 and get back the full potential of this tried and true motor.

This kit includes everything you need to do the clutch and flywheel service on your M20. While you're in there it is a good idea also to purchase the common transmission seals, fluid, and mounting hardware which are listed below.

Clutch Kit:

Sachs OE replacement clutch disc - 21211223097
Sachs pressure plate - 21211223026
Sachs 323 throw-out bearing (taller bell housing/ETA models) - 21511204525
Pilot bearing - 11211720310
Turner Single-Mass Flywheel:

Lightweight flywheel for quicker, effortless revs that improve throttle response and free up lost horsepower. Tested and approved by the engineering team at Turner Motorsport, tested in early, late, ETA and IS model E30s for confirmed fitment.
Fits shallow and deep bell housing transmissions
Ring gear suited for both starters (P# 12411726504 + 12411361874)
Heavier than other lightweight flywheels, and lighter than OEM, it's like the Goldie Locks of flywheels - it's just right
Reference pin for bell housing crank sensor
Strong Single-Piece 4140 HT Steel construction
Designed to be used with factory and OE clutches
Weight savings between 5-14lbs depending on your OE flywheel

Components strongly suggested while your transmission is out of the car.:

Transmission Seals Kit - T#29898446
Fluid - 75-90 or preferred fluid type (approximately 1.25 liters)
Transmission Mounting hardware - T#30197962

This Genuine BMW OE replacement clutch kit from BMW comes stock for the 335is, 550i, and 650i. A lot of our customers install this as an upgrade for the 135i 335i and 535i!

Includes:

• Clutch friction disc
• Throwout/release bearing
• Clutch fork lever
• Pressure plate
• Pressure plate bolts

 
Genuine BMW Clutch Kit for your 6 Speed Manual Transmission vehicle - 
This item fits the following BMW Chassis:
E92,E93,F10,F12,F13

If your clutch switch is bad, it will prevent the car from starting and seem similar to a bad starter, you will turn the key and nothing will happen. Replace yours to start your vehicle again.

Genuine BMW Module, Clutch Switch
This item fits the following BMW Chassis:
E39 M5,E46 M3,E85 Z4M,E39,E46,E85 Z4,E86 Z4
 

Replace your leaking or worn clutch master cylinder with this replacement master cylinder.

This item fits the following BMWs:
5/1997-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
5/1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Roadster