Find Parts That Fit Your Vehicle

Turbos

If more boost and reliability are your goals choose from one of our BMW turbo upgrades. Our turbo upgrades range from stock turbos rebuilt with stronger internals to all-new, ground-up turbo upgrades. BMW turbos such as the N54 are capable of really impressive power numbers on stock engine internals but the factory turbos lack the precise tolerances and reliability that an upgraded unit will deliver. In other words, the stock turbos can only do so much and if big power (>400whp) is your goal a turbo upgrade must be in your plans. Our partners are leading experts in turbo technology and upgrades. Each Stage has been professionally developed and tested. Additional upgrades and tuning may be, or is, required. Contact us for more details on tuning options.

Sub-Categories

Sort By:

N54 Turbocharger Installation Kit - Front And Rear
Packaged by Turner - Corporate Logo
T#:401684
Part#: 13712247398KT2
In Stock
Sale - Save 10% $295.14
$265.63
Free Shipping
Sale - Save 10% $295.14
$265.63
Free Shipping

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

  • 16 - ASA M7x39 studs
  • 16 - Flange nuts
  • All required gaskets and o-rings
  • Water pump install hardware
  • Replacement vacuum hose
  • T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

Show More Show Less
MAC Single Turbo Boost Solenoid - N54 N55
Burger Motorsports - Corporate Logo
T#:587715
Part#: MACSTS
In Stock
$54.99
Free Shipping on orders $49 and up
Use this plug and play low frequency MAC solenoid if retrofitting a single turbo kit to your N54 or N55. Includes plug and play harness connector for no splicing!
VRSF 1.75" OEM Location High Flow Silicone Inlet Kit - N54
VRSF - Corporate Logo
T#:585220
Part#: 10901050
In Stock
$229.99
Free Shipping on orders $49 and up
Improve your restrictive OEM intake with this 1.75" Relocated Silicone High Flow Inlet Kit. You will experience drastic increases in flow especially in mid to upper RPM ranges, as well as a more aggressive exhaust note. The VRSF OEM location inlet upgrade kit provides a more direct, high flowing intake path for your turbos. This kit includes everything you need to replace the OEM inlets, including relocation brackets, filters, hoses, and the steel wire reinforced silicon tubing.
Show More Show Less

Schwaben 11mm Brake Bleeder Wrench
Schwaben - Corporate Logo
T#:362403
Part#: 000550SCH01A
In Stock
Sale - Save 15% $25.95
$22.06
Free Shipping on orders $49 and up
Sale - Save 15% $25.95
$22.06
Free Shipping on orders $49 and up
Finally, a bleeder wrench with just the right angle to open the bleeder screw without having to spend all that time removing each wheel from your car.

Wagner Tuning Competition Intercooler Kit with Logo - F8X M3/M4
Wagner Tuning - Corporate Logo
T#:587595
Part#: 200001124.LOGO
In Stock
$1,990.00