BMW Suspension Parts for BMW 3 Series E92 (2007-2013)

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

Our E90 E92 E93 fixed camber plates are designed from the knowledge we gained from our highly successful racing campaigns with the E46 in the Speed World Challenge series. Our camber plates are offset for the best camber and caster combination for racing purposes when using the stock-diameter sized springs. Camber increases to -2.5° depending on your individual suspension setup, while only increasing ride height by 6mm. The rate of camber change is virtually unaffected throughout the range of suspension travel, reducing the need for other geometry correction. Fixed mount camber plates are legal in many racing and autocross classes - these are the perfect camber solution when adjustable plates are not allowed in your class.

These are very simple to install, requiring only pressing out locator dowels and studs in your factory strut mounts. See below for detailed instructions.

A BMWs sub-frame is the heart of the suspension - as the subframe twists and shifts under load all of the suspension mounting points also move. The rear suspension feels loose and lacks precision. As rubber or hydroelastic bushings wear the bushing deflection gets worse. If you have a highly tuned 335i/xi you're putting even more strain on weak bushings. The solution is a stiffer and more durable material. Even BMW has moved to solid mounts on the F10 M5 and F8X M3/M4. These fully solid E82/E90/E92 aluminum mounts have zero deflection - the subframe does not move at all. The rest of the suspension can work as designed and maintain the proper alignment and motion ratios. The driver will notice the difference as the car is more stable and the handling is more precise.

Although we designed these for use in our racecars, they can work on the street so long as the driver can tolerate some additional noise, vibration, and harshness. These mounts are CNC machined in the USA and made with high-grade aluminum. The set is for all four subframe mounts.

These solid rear sub frame mounts fit: 
2008-2012 E82 BMW 128i 135i 
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan 
2006-2011 E91 BMW 325i 328i - Wagon 
2007-2012 E92 BMW 328i 335i 335is - Coupe 
2007-2012 E93 BMW 328i 335i - Convertible 

M3 upper and lower control arms are a known upgrade for non-M E82 and E9X chassis. But our Monoball Thurst Arms are even more of an upgrade over the stock M3 arms. This package bundles the Turner Monoball upper thrust arms with the stock M3 lower control arms. If there's one big fail point in the E82/E9X front suspension it's the thrust arms. The front inner thrust arm bushing is filled with dampening fluid that leaks over time. Once it's gone the bushing has the strength of a rubber band. Even though we sell two types of upgraded rubber bushings there was still room for improvement. For someone looking for superior performance and longevity these sealed monoball bushings are the best out there. 

The advantage of a monoball bearing is that it will not deflect under load. All of the rubber bushings, including the M3, move in all sorts of directions and that changes your alignment, especially when used with big brake kits or when driven hard. And when worn out, performance suffers. Our monoball sits in a CNC machined aluminum housing which has zero deflection. The monoball allows complete freedom of movement but only at the desired angles. What you get is superior steering precision, better handling from more consistent alignment, and almost infinite bushing life. And thanks to the inner liner and sealed rubber boots there's none of the extra noise or reduced service life of fully solid race bushings.

The lower M3 control arm bushings use a similar sealed monoball bushing instead of rubber. This package gives you monoball precision and performance with OE-quality components.

This item fits the following BMWs: 
2008-2012 E82 BMW 128i 135i 1M Coupe 
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan 
2006-2012 E91 BMW 328i - Wagon 
2007-2013 E92 BMW 328i 335i 335is M3 - Coupe 
2007-2013 E93 BMW 328i 335i M3 - Convertible 
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is 

Rubber mounts in any position of a vehicle are usually designed with comfort and longevity in mind leaving performance as a sacrifice. This kind of sacrifice here at Turner just won't do, so we did what we do best and designed a solid monoball mount.

Our engineering team first wanted to tackle the issue with wear found on rubber mounts. Due to their combination of steel, rubber, and low mounting location, these mounts are a direct target for deterioration and failure. As they are positioned out in the open and exposed to the elements, bonded steel and rubber components inevitably hold moisture, separating as the steel bearing begins to rust. Our solution was to offer a rebuildable mount with a Teflon lined bearing for increased durability, combined with a blue anodized body and melonite coated bushing sleeves for corrosion resistance.

The performance side of these mounts is primarily found in the articulation allowed by the bearing. Rubber mounts do not allow for proper free damper movement, hindering shock performance. By eliminating the deflection found in factory rubber mounts and allowing full shock articulation, this solid monoball design eliminates slop and maximizes shock efficiency and performance, allowing for more predictable handling on the street or the track - with almost zero added noise, vibration, and harshness.

Replaces OE part #: 33526768544

Key Benefits:

• Monoball rear lower shock mount eliminates unwanted deflection, maximizing shock efficiency and performance.
• Allows full shock body articulation for low friction movement and reduced side loading and improved shock wear.
• Designed to work with stock non-M taper seat stud style shocks (not M eyelet mount type).
• Maintains OE shock position

Design features:

• Rebuildable using off the shelf bearings - these are the last rear shock mounts you’ll need to buy
• Includes new hardware
• Made in USA

Housing:

• Billet CNC 6061-T6 aluminum housing, type II anodized for exceptional durability and corrosion resistance

Bearing:

• FK WSSX14T teflon lined spherical bearing
• 440C heat-treated stainless steel ball, 1 ⅜” ball dia.
• 17-4 PH heat-treated stainless steel race
• Self-lubricating PTFE liners are chemically bonded to the inner diameter of the race to offer a very high load-carrying capacity with greatly increased dynamic wear characteristics.
• Static Axial Load Rating: 10,800 lbs.
• Rod End Misalign Angle: 6 degrees

Bearing inserts:

• CNC machined 1144 steel, heat treated and melonite coated designed to maximize ball articulation while offering exceptional durability and corrosion resistance.

This item fits the following BMWs: 
2008-2013 E82 BMW 128i 135i 135is Coupe 
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan 
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon 
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe 
2007-2013 E93 BMW 328i 335i 335is - Convertible 

This kit is contains all new strut and shock mounts and hardware needed when installing a new shocks and struts or aftermarket suspension on your vehicle. 

Fits the following BMW's

E82/88 128i 135i

E90/92/93 325i 328i 330i 335i 335is 

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Front Control Arms
Front Control Arm Bushings
Front Sway Bar End Links & Bushings
Front Ball Joints
New Hardware

These M3 rear guide rod arms are an upgrade for the non-M cars. The stock non-M arms are made from sheetmetal spot welded together at the ends. The arm tends to flex and bend under even moderate cornering loads. Factor in gripper tires and more torque and this arm is inadequate for stability and consistent handling. The M3 arms are one piece of aluminum offering greater strength and with a sealed monoball inner bushing that allows the arm to rotate (instead of twisting).

This package includes:

• Left M3 Guide Rod - 33322283547
• Right M3 Guide Rod - 33322283548

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Rear Sway Bar End Links
Rear Trailing Arm Bushings
Rear Strut Mounts
New Hardware

Replacing your struts and shocks? Don't forget the bushings! The rubber mounts for the shocks will go bad over time, especially if you drive hard or the roads are particularly rough. The shock mounts locate the front struts and rear shocks to the car - providing a quiet and vibration-free buffer between the road and the cabin. Shock mounts and bushings can wear out just like any other rubber part on the car. This leads to more noise and harshness reaching the chassis and may complicate your new suspension install. When installing new shocks, that is the perfect time to also replace the mounts. There is no additional time to install them, no special tools required, and doesn't take any extra time! If you re-use the original mounts you have the risk of them failing before your next shock replacement, doubling your labor costs. 

This item fits the following BMWs: 
2006-2012 E9X BMW All xi models - 325xi 328xi 330xi 335xi